Skip to contentSkip to conversation

Compact Flash - simulating a card

DISCUSSION Justin Patrin 2 participants 4 messages Nov 23, 2004 – Nov 24, 2004

lore
Share & tools
lore
#0 lore raw

I am not currently subscribed to this list as I figure I'll be shunted to another anyway. Please CC me on replies to this thread. If I should be asking "someone else" whether it be another list or group, let me know.

I currently have a Sharp Zaurus with OpenZaurus on it. I'm trying to connect a device to the CF slot. Would is be possible to fake the CF "startup"? I.e. connect a dumb device (which does not understand the CF spec itself) but have the kernel able to pass certain requests on to it? I have tried connecting the device and it sees it (as I've hooked up the detection pins) but something times out. Sorry, I don't have the exact message at the moment.

Signature · 1 line
Justin Patrin
#1 lore raw

This is actually not really of topic, so so much for getting shunted.

Anyway:
If you edit the modules part (manuals enough on the internet, watch your kernel version, because modules changed a bit between 2.4 and 2.6 kernels), you can force the identifier of your card to be matched with a CF device. Take the best matching device.
If you don't have any match at all, you have a problem, i.e. it will not work.

I don't know the Zaurus (except from a nice picture), so I don't know what kind of port is used for the CF card (IDE? PCMCIA? other?). If it is an IDE port, it should work at once. It does not need any other information.

For the rest it sounds to me like you are doing a hardware hack.

Regards,

Norbert

Quoted 12 lines · Justin Patrin

I am not currently subscribed to this list as I figure I'll be shunted to another anyway. Please CC me on replies to this thread. If I should be asking "someone else" whether it be another list or group, let me know.

I currently have a Sharp Zaurus with OpenZaurus on it. I'm trying to connect a device to the CF slot. Would is be possible to fake the CF "startup"? I.e. connect a dumb device (which does not understand the CF spec itself) but have the kernel able to pass certain requests on to it? I have tried connecting the device and it sees it (as I've hooked up the detection pins) but something times out. Sorry, I don't have the exact message at the moment.

#2 lore raw
Quoted 9 lines · Norbert van Nobelen

This is actually not really of topic, so so much for getting shunted.

Anyway:
If you edit the modules part (manuals enough on the internet, watch your kernel version, because modules changed a bit between 2.4 and 2.6 kernels), you can force the identifier of your card to be matched with a CF device. Take the best matching device.
If you don't have any match at all, you have a problem, i.e. it will not work.

Well, it should be a storage device...

Quoted 3 lines

I don't know the Zaurus (except from a nice picture), so I don't know what kind of port is used for the CF card (IDE? PCMCIA? other?). If it is an IDE port, it should work at once. It does not need any other information.

It's got a normal CF slot with (I think) a PCMCIA bridge. You can plug in CF memory crad and microdrives as well as CF Wifi cards.

Basically I would want to connect the CF card as an IDE device (I have no idea how to expose one device as another, although I think the current CF storage device driver does this).

Quoted 2 lines

For the rest it sounds to me like you are doing a hardware hack.

So you think that I could force the kernel to assume that a device is present? Meaning that there's no hardware-level stuff that has to happen?

Of course the hard part is *where* I would edit the kernel for this...probably in the PCMCIA stuff. I know that that's where the timout message I was seeing was coming from.

Quoted 22 lines

Regards,

Norbert

Quoted 12 lines · Justin Patrin

I am not currently subscribed to this list as I figure I'll be shunted to another anyway. Please CC me on replies to this thread. If I should be asking "someone else" whether it be another list or group, let me know.

I currently have a Sharp Zaurus with OpenZaurus on it. I'm trying to connect a device to the CF slot. Would is be possible to fake the CF "startup"? I.e. connect a dumb device (which does not understand the CF spec itself) but have the kernel able to pass certain requests on to it? I have tried connecting the device and it sees it (as I've hooked up the detection pins) but something times out. Sorry, I don't have the exact message at the moment.

Signature · 1 line
Justin Patrin
#3 lore raw
Quoted 15 lines · Justin Patrin

On Wed, 24 Nov 2004 06:42:14 +0100, Norbert van Nobelen

Quoted 9 lines · <[email protected]> wrote:

This is actually not really of topic, so so much for getting shunted.

Anyway:
If you edit the modules part (manuals enough on the internet, watch your kernel version, because modules changed a bit between 2.4 and 2.6 kernels), you can force the identifier of your card to be matched with a CF device. Take the best matching device.
If you don't have any match at all, you have a problem, i.e. it will not work.

Well, it should be a storage device...

Quoted 7 lines
Quoted 4 lines

I don't know the Zaurus (except from a nice picture), so I don't know what kind of port is used for the CF card (IDE? PCMCIA? other?). If it is an IDE port, it should work at once. It does not need any other information.

It's got a normal CF slot with (I think) a PCMCIA bridge. You can plug in CF memory crad and microdrives as well as CF Wifi cards.

Look in the logs for pcmcia messages, and the Zaurus manual for info over the slot. It will help you a bit further. I would assume pcmcia too given the information.

Quoted 4 lines

Basically I would want to connect the CF card as an IDE device (I have no idea how to expose one device as another, although I think the current CF storage device driver does this).

Just insert it in the slot? If that does not work. In the cs-ide module can be a mistake in some 2.4 versions of the kernel: there is a dash somewhere in the nameing which should be an underscore.

Quoted 6 lines
Quoted 2 lines

For the rest it sounds to me like you are doing a hardware hack.

So you think that I could force the kernel to assume that a device is present? Meaning that there's no hardware-level stuff that has to happen?

You could do that, inserting the card and just getting it to work is probably easier. I have no clue yet of what the kernel will do when you convince it that the card is there, and it will try to address it.
What you could do is create a dummy device based on the ide device in which you print debug information. Maybe a skeleton of such a dummy device is around somewhere (google?).

Quoted 22 lines

Of course the hard part is *where* I would edit the kernel for this...probably in the PCMCIA stuff. I know that that's where the timout message I was seeing was coming from.

Quoted 17 lines

Regards,

Norbert

Quoted 12 lines · Justin Patrin

I am not currently subscribed to this list as I figure I'll be shunted to another anyway. Please CC me on replies to this thread. If I should be asking "someone else" whether it be another list or group, let me know.

I currently have a Sharp Zaurus with OpenZaurus on it. I'm trying to connect a device to the CF slot. Would is be possible to fake the CF "startup"? I.e. connect a dumb device (which does not understand the CF spec itself) but have the kernel able to pass certain requests on to it? I have tried connecting the device and it sees it (as I've hooked up the detection pins) but something times out. Sorry, I don't have the exact message at the moment.