Skip to contentSkip to conversation

In eth0 out eth1

LARTC Rudi Starcevic 1 participant 1 message Oct 24, 2005

lore
Share & tools
lore
#0 lore raw

Hello,

I have a routing configuration that I've been working on and seems to be working well for me.

I'd like to ask for some peer review.
If your interested and can take a moment to consider this
I could use some advice on if this correct. I'm still very much learning, sorry if this email is off topic or too long or anything.

I want to route a wireless network through my Linux box and out a Broadband gateway.

The wireless network is 192.168.3.0/24

The Linux machine has eth0 for the wireless network and eth1 for the Broadband gateway.

Here is a text diagram:
http://www.informationobject.com/iproute/c_schema.txt

Thus a PC can be added to the wireless work
and set it's default gateway to 192.168.3.10.

I have two scripts to configure the Linux machine to forward/route traffic from eth0 to eth1 and out the Broadband gateway.

One script for route config. and one script for firewall/iptables config. They are listed here and also at:
http://www.informationobject.com/iproute/a_route.txt
http://www.informationobject.com/iproute/b_firewall.txt

Would you say this is the correct way to go about doing this routing configuration?
Thank you.

echo "Route Setup"

echo "Flushing NICs"
ip addr flush eth0
ip addr flush eth1

ip link set eth0 down
ip link set eth1 down

ip link set eth0 up
ip link set eth1 up

echo "Routing Tables:"
cat /etc/iproute2/rt_tables
### example rt_tables ###
## reserved values
##

#255    local
#254    main
#253    default
#0      unspec
##
## local
##
##1     inr.ruhep
#200    wireless
#201    internet

### example end ###

echo "Setup NIC 0"
ip addr add 192.168.3.10/24 dev eth0 brd +

echo "Setup NIC 1"
ip addr add 192.168.1.1/24 dev eth1 brd +

echo "Setup Default Route [ internet table ]"
ip route add default via 192.168.1.254 proto static table internet

echo "Setup LAN Route [ wireless table ]"
ip route add 192.168.3/24 via 192.168.3.10 proto static table wireless

echo "Setup Internet ip rule"
ip rule add to 0/0 prio 17000 table internet

echo "Setup LAN ip rule"
ip rule add to 192.168.3/24 prio 16000 table wireless

echo "Flushing ip route cache"
ip route flush cache

echo "Firewall Setup"

################################################################################

# Enable forwarding
echo "Enable Kernel Forwarding"
echo 1 > /proc/sys/net/ipv4/ip_forward

################################################################################
echo -n "reset "

for chain in INPUT FORWARD OUTPUT ; do
iptables --policy $chain DROP
done

for table in filter nat mangle ; do
iptables --table $table --flush
iptables --table $table --delete-chain
done

modprobe ip_nat_ftp

################################################################################
echo -n "INPUT "

# accept everything from wireless
iptables -A INPUT -i eth0 -s 192.168.3.0/24 -j ACCEPT

iptables -A INPUT -i lo -j ACCEPT
iptables -A INPUT -i eth1 -s 192.168.1.0/24 -j ACCEPT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT

################################################################################
echo -n "FORWARD "
iptables -A FORWARD -i eth0 -j ACCEPT
iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT

################################################################################
echo -n "OUTPUT "

# allows unrestricted output from this machine
iptables -A OUTPUT -o lo -j ACCEPT
iptables -A OUTPUT -o eth0 -j ACCEPT
iptables -A OUTPUT -o eth1 -j ACCEPT

################################################################################
echo done.

Kind regards,
Rudi.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc