Help about tftp download
Hi everyone:
I am trying to download u-boot.bin to OMAP5912OSK through tftp. But when I type the commad in u-boot prompt, it shows following error messages:
OMAP5912 OSK # tftpboot 0x10000000 /tftpboot/u-boot.bin TFTP from server 192.168.4.1; our IP address is 192.168.4.190 Filename '/tftpboot/u-boot.bin'.
Load address: 0x10000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
.......
What's wrong with my setups?
Thank you and best regards!
Li Weichen
2005-11-1
Quoted 12 lines · In message <[email protected]> you wrote:
I am trying to download u-boot.bin to OMAP5912OSK through tftp. But when I type the commad in u-boot prompt, it shows following error messages:
OMAP5912 OSK # tftpboot
0x10000000/tftpboot/u-boot.bin TFTP from server 192.168.4.1; our IP address is 192.168.4.190 Filename '/tftpboot/u-boot.bin'.
Load address:0x10000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
.......
Quoted 1 line
What's wrong with my setups?
Given the little detail you provide: it's impossible to say. Maybe your hardware is broke, or the port of U-Boot to your board, or you use an illegal MAC address, or ...
Best regards,
Wolfgang Denk
Signature · 3 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "The whole world is about three drinks behind." - Humphrey Bogart
Hi Li,
The "T T T T T" messages indicate a timeout, which means the client thinks the packets are going out and not getting a reply. I've seen this many times and
it can mean many different things. I'm not all-knowing and all-seeing, but I can make some suggestions. First, make sure that you have a file called "tftp" in /etc/xinetd.d/ (assuming you use xinetd rather than inetd). The file should look something like this:
service tftp
{
disable = no
socket_type = dgram
protocol = udp
wait = yes
user = root
server = /usr/sbin/in.tftpd
}
# server_args = /tftpboot
Second, make sure you have /usr/sbin/in.tftpd and if not, get it.
Third, make sure there aren't any duplicate devices in your network that may be holding the same address your tftp client is trying to use.
Fourth, check your client's u-boot environment variables to make sure the settings
are right for client and server ip addresses.
If none of this works, use /usr/sbin/tcpdump -i eth0 (whatever your ethX is) on your host to see if the tftp packets are making it to the host at all.
Hope this helps.
Regards,
Bob Peterson
Quoted 19 lines · Li Weichen
Hi everyone:
I am trying to download u-boot.bin to OMAP5912OSK through tftp. But when I type the commad in u-boot prompt, it shows following error messages:
OMAP5912 OSK # tftpboot
0x10000000/tftpboot/u-boot.bin TFTP from server 192.168.4.1; our IP address is 192.168.4.190 Filename '/tftpboot/u-boot.bin'.
Load address:0x10000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
.......What's wrong with my setups?
Thank you and best regards!
Li Weichen
2005-11-1
Quoted 26 lines
Quoted 14 lines · Li Weichen
Hi everyone:
I am trying to download u-boot.bin to OMAP5912OSK through tftp. But when I
type the commad in u-boot prompt, it shows following error messages:OMAP5912 OSK # tftpboot
0x10000000/tftpboot/u-boot.bin TFTP from server 192.168.4.1; our IP address is 192.168.4.190 Filename '/tftpboot/u-boot.bin'.
Load address:0x10000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
.......Quoted 6 lines
What's wrong with my setups?
Thank you and best regards!
Li Weichen
2005-11-1Bob Peterson wrote:
Hi Li,
Quoted 6 lines
The "T T T T T" messages indicate a timeout, which means the client thinks the packets are going out and not getting a reply. I've seen this many times and
it can mean many different things. I'm not all-knowing and all-seeing, but I
can make some suggestions. First, make sure that you have a file called
[snipped good advice]
Quoted 5 lines
Hope this helps.
Regards,
Bob Peterson
Another suggestion: from a (linux) box command line, tftp to your server and verify that it works. Your message is indicating that your server is 192.168.4.1 and the file you are trying to get is /tftpboot/u-boot.bin so do the following (I'm typing this from memory, so it may not be quite right)...
$ tftp 192.168.4.1 tftp> get /tftpboot/u-boot.bin
Getting TFTP to work (i.e. properly configured) usually solves the problem in my experience.
gvb
Hi Bob,
Thanks for your kind reply. I have tried your instructions. My system is Debian-amd64 sarge 3.1, so my configurations is more or less a little different from that in Redhat. My tftpd is configured in /etc/inetd.conf. There is a line is this file looks like
tftp dgram udp wait root /usr/sbin/tcpd /usr/sbin/in.tftpd /tftpboot
There are only my host and target board in my local net.
After I typed #tcpdump -i eth1, the messages are following,
# tcpdump -i eth1 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 96 bytes 18:11:30.010752 arp who-has omap1.Nankai.edu.cn tell 192.168.4.190 18:11:30.012669 arp reply omap1.Nankai.edu.cn is-at 00:e0:4c:df:3d:48 18:11:30.011040 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.tftp: 39 RRQ "/tftpboot/u-boot.bin" octet timeout 5 18:11:30.012061 IP 192.168.0.11.33311 > 192.168.4.190.2805: UDP, length: 12 18:11:30.012359 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:30.012382 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:30.635567 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:30.635607 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:31.260528 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:31.260567 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:31.885490 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:31.885529 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:32.510452 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:32.510492 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:33.135414 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:33.135454 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:33.226036 IP 192.168.0.11.33304 > 192.168.4.190.2248: UDP, length: 12 18:11:33.760376 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:33.760416 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:34.385347 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:34.385388 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:35.010310 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:35.010349 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:35.010732 arp who-has 192.168.4.190 tell omap1.Nankai.edu.cn 18:11:35.010891 IP 192.168.0.11.33311 > 192.168.4.190.2805: UDP, length: 12 18:11:35.011042 arp reply 192.168.4.190 is-at 00:0e:99:02:0a:21 18:11:35.011254 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:35.011268 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:35.635276 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:35.635314 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:36.260237 IP 192.168.4.190.2805 > omap1.Nankai.edu.cn.33311: UDP, length: 4 18:11:36.260275 IP omap1.Nankai.edu.cn > 192.168.4.190: icmp 40: omap1.Nankai.edu.cn udp port 33311 unreachable 18:11:38.152001 arp who-has omap1.Nankai.edu.cn tell 192.168.4.190
............
omap1.Nankai.edu.cn is my hostname, 192.168.0.11 is the IP of eth0 witch is connected to external LAN. If the message above shows that my client setup is correct? I am wondering about why the UDP packets were sent to 192.168.0.11 rather than 192.168.4.1? Is it the problem?
Quoted 9 lines
Another suggestion: from a (linux) box command line, tftp to your server and verify that it works. Your message is indicating that your server is 192.168.4.1 and the file you are trying to get is /tftpboot/u-boot.bin so do the following (I'm typing this from memory, so it may not be quite right)...
$ tftp 192.168.4.1 tftp> get /tftpboot/u-boot.bin
Sorry but after I typed tftp 192.168.4.1, it came up with message looks like get uImage froam tftp server automatically.
Quoted 5 lines
Getting TFTP to work (i.e. properly configured) usually solves the problem in my experience.
gvb
I think the network is fine, because if I wanted to get a file that not exist in /tftpboot, if shows that file not found. And there are only the host and target board in the local net.
If I tried tcpdump I found the target board had got the correct IP.
Quoted 10 lines
-----Original Message-----
From: wd at denx.de [mailto:wd at denx.de]
Sent: Tuesday, November 01, 2005 9:12 PM
To: Li Weichen
Cc: u-boot-users at lists.sourceforge.net
Subject: Re: [U-Boot-Users] Help about tftp downloadQuoted 2 lines · In message <[email protected]> you wrote:
I am trying to download u-boot.bin to OMAP5912OSK through tftp. But
when
Quoted 25 lines
I
Quoted 11 lines
type the commad in u-boot prompt, it shows following error messages:
OMAP5912 OSK # tftpboot
0x10000000/tftpboot/u-boot.bin TFTP from server 192.168.4.1; our IP address is 192.168.4.190 Filename '/tftpboot/u-boot.bin'.
Load address:0x10000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
.......What's wrong with my setups?
Given the little detail you provide: it's impossible to say. Maybe your hardware is broke, or the port of U-Boot to your board, or you use an illegal MAC address, or ...
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"The whole world is about three drinks behind." - Humphrey Bogart
Quoted 6 lines · Li Weichen
Quoted 6 lines
Another suggestion: from a (linux) box command line, tftp to your server and verify that it works. Your message is indicating that your server is 192.168.4.1 and the file you are trying to get is /tftpboot/u-boot.bin so do the following (I'm typing this from memory, so it may not be quite right)...
Quoted 10 lines
Quoted 2 lines
$ tftp 192.168.4.1 tftp> get /tftpboot/u-boot.binSorry but after I typed tftp 192.168.4.1, it came up with message looks like get uImage froam tftp server automatically.
Quoted 4 lines
Getting TFTP to work (i.e. properly configured) usually solves the problem in my experience.
gvb
Hi Li,
You result description ment nothing to me. Please cut & paste real messages. Are you typing "tftp 192.168.4.1" from your _host_ (linux server) command line?
OK, I ran a real instance on my home box (Debian 3.1 x86) vanbaren at dellserver:~$ uname -a
Linux dellserver.lan 2.4.27-050821 #17 SMP Sun Aug 21 22:46:01 EDT 2005 i686 GNU/Linux
vanbaren at dellserver:~$ dpkg-query -l "*tftp*" Desired=Unknown/Install/Remove/Purge/Hold
| Status=Not/Installed/Config-files/Unpacked/Failed-config/Half-installed |/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err:
uppercase=bad)
||/ Name Version Description
+++-==============-==============-============================================
ii tftp 0.17-13 Trivial file transfer protocol client ii tftpd 0.17-13 Trivial file transfer protocol server
vanbaren at dellserver:~$ ls /tftpboot/hello_world hello_world
vanbaren at dellserver:~$ tftp localhost
tftp> get hello_world
Received 101214 bytes in 0.1 seconds
tftp> get /tftpboot/hello_world
Received 101214 bytes in 0.0 seconds
tftp> quit
vanbaren at dellserver:~$ grep tftp /etc/inetd.conf
tftp dgram udp wait nobody /usr/sbin/tcpd/usr/sbin/in.tftpd /tftpboot
I was a little surprised that the tftp "get" worked with the /tftpboot full path. On a different box that I used (RH), it is configured as "-s /tftpboot" for the option (rather than "/tftpboot") so tftpd treats paths as relative to /tftpboot and thus the get "/tftpboot/foo" won't work because there is no /tftpboot/tftpboot/foo on the server. This should not be your problem since your configuration matches mine.
HTH,
gvb
I have found the reason. My host PC has 2 ethernet cards, and the tftp server is installed on the eth0 which ip is 192.168.0.11.
Thank you for your reply!
Quoted 8 lines
-----Original Message-----
From: u-boot-users-admin at lists.sourceforge.net [mailto:u-boot-users-admin at lists.sourceforge.net] On Behalf Of Jerry Van Baren
Sent: Wednesday, November 02, 2005 8:59 PM
To: u-boot-users at lists.sourceforge.net
Subject: Re: [U-Boot-Users] Help about tftp download
Quoted 11 lines
Quoted 10 lines · Li Weichen
Quoted 8 lines
Another suggestion: from a (linux) box command line, tftp to your server and verify that it works. Your message is indicating that your server is 192.168.4.1 and the file you are trying to get is /tftpboot/u-boot.bin so do the following (I'm typing this from memory, so it may not be quite right)...
$ tftp 192.168.4.1 tftp> get /tftpboot/u-boot.binSorry but after I typed tftp 192.168.4.1, it came up with message looks
like
Quoted 52 lines
Quoted 6 lines
get uImage froam tftp server automatically.
Quoted 4 lines
Getting TFTP to work (i.e. properly configured) usually solves the problem in my experience.
gvb
Hi Li,
You result description ment nothing to me. Please cut & paste real messages. Are you typing "tftp 192.168.4.1" from your _host_ (linux server) command line?
OK, I ran a real instance on my home box (Debian 3.1 x86) vanbaren at dellserver:~$ uname -a
Linux dellserver.lan 2.4.27-050821 #17 SMP Sun Aug 21 22:46:01 EDT 2005 i686 GNU/Linuxvanbaren at dellserver:~$ dpkg-query -l "*tftp*" Desired=Unknown/Install/Remove/Purge/Hold
| Status=Not/Installed/Config-files/Unpacked/Failed-config/Half-installed |/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err:
uppercase=bad)
||/ Name Version Description
+++-==============-==============-========================================
====ii tftp 0.17-13 Trivial file transfer protocol client ii tftpd 0.17-13 Trivial file transfer protocol servervanbaren at dellserver:~$ ls /tftpboot/hello_world
hello_worldvanbaren at dellserver:~$ tftp localhost
tftp> gethello_world
Received 101214 bytes in 0.1 seconds
tftp> get /tftpboot/hello_world
Received 101214 bytes in 0.0 seconds
tftp> quitvanbaren at dellserver:~$ grep tftp
/etc/inetd.conf
tftp dgram udp wait nobody/usr/sbin/tcpd/usr/sbin/in.tftpd/tftpbootI was a little surprised that the tftp "get" worked with the /tftpboot full path. On a different box that I used (RH), it is configured as "-s /tftpboot" for the option (rather than "/tftpboot") so tftpd treats paths as relative to /tftpboot and thus the get "/tftpboot/foo" won't work because there is no /tftpboot/tftpboot/foo on the server. This should not be your problem since your configuration matches mine.
Quoted 7 lines
HTH,
gvb-------------------------------------------------------
SF.Net email is sponsored by:
Tame your development challenges with Apache's Geronimo App Server.
Download
Quoted 6 lines
it for free - -and be entered to win a 42" plasma tv or your very own Sony(tm)PSP. Click here to play: http://sourceforge.net/geronimo.php
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users