kernel 2.6.15-rc5-latest doesn't work anymore on mpc8540ads
Hello,
I am just about to update my kernel from 2.6.13-rc7 which is working fine to linus' 2.6.15-rc5-latest git on my mpc8540ads flavored board. However, the kernel hangs pretty early after
openpic: exit
any ideas or a hint what's wrong there... before I start to debug deeper into the code?
Thanks,
Clemens
-----8<-----
U-Boot 1.1.3 (Jun 23 2005 - 10:40:01)
CPU: 8540, Version: 2.0, (0x80300020)
Core: E500, Version: 2.0, (0x80200020)
Clocks Configuration:
CPU: 825 MHz, CCB: 330 MHz,
DDR: 165 MHz, LBC: 82 MHzL1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: MicroSys PM854
PCI1: 32 bit, 66 MHz (compiled)
I2C: ready DRAM: Initializing DDR: 256 MB FLASH: 32 MB L2: 256 kB enabled In: serial Out: serial Err: serial Net: ENET0: PHY is Marvell 88E1111S (1410cc2) ENET1: PHY is Marvell 88E1111S (1410cc2) ENET2: PHY is LXT971 (1378e2) ENET0, ENET1, ENET2 Hit any key to stop autoboot: 0 ## Booting image at fe300000 ... Image Name: Linux-2.6.15-rc5-g7116317d Created: 2005-12-16 15:30:40 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1394968 Bytes = 1.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OKmpc8540ads_init(): exit
id mach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:setio
MMU:exitsetup_arch: entersetup_arch: bootmemmpc8540ads_setup_arch()
arch: exit
openpic: enter
openpic: timer
openpic: external
openpic: spurious
openpic: exit
-----8<----
Signature · 11 lines
Clemens Koller _______________________________ R&D Imaging Devices Anagramm GmbH Rupert-Mayer-Str. 45/1 81379 Muenchen Germany http://www.anagramm.de Phone: +49-89-741518-50 Fax: +49-89-741518-19
Hello!
Here is a little update:
Quoted 5 lines
I am just about to update my kernel from 2.6.13-rc7 which is working fine to linus' 2.6.15-rc5-latest git on my mpc8540ads flavored board. However, the kernel hangs pretty early after
openpic: exit
openpic_init() is called by mpc85xx_ads_init_IRQ in ppc/platforms/85xx
ppc_md.init_IRQ=mpc85xx_ads_init_IRQ in ppc/platforms/85xx
ppc_md.init_IRQ() is called from powerpc/kernel/irq.c
init_IRQ() is called from init/main.c:start_kernel()
and that seems to work fine. So, it crashes silently somewhere after that point. I try to build 2.6.15-rc6-latest with kgbd support, not knowing if it's supposed to work on this platform.
Are there some open issues from the ppc->powerpc migration?
Thanks,
Signature · 11 lines
Clemens Koller _______________________________ R&D Imaging Devices Anagramm GmbH Rupert-Mayer-Str. 45/1 81379 Muenchen Germany http://www.anagramm.de Phone: +49-89-741518-50 Fax: +49-89-741518-19
Quoted 14 lines · Clemens Koller
Hello!
Here is a little update:
Quoted 5 lines
I am just about to update my kernel from 2.6.13-rc7 which is working fine to linus' 2.6.15-rc5-latest git on my mpc8540ads flavored board. However, the kernel hangs pretty early after
openpic: exit
openpic_init()is called bympc85xx_ads_init_IRQin ppc/platforms/85xxppc_md.init_IRQ=mpc85xx_ads_init_IRQ in ppc/platforms/85xx
Quoted 7 lines
ppc_md.init_IRQ()is called frompowerpc/kernel/irq.c
init_IRQ()is called from init/main.c:start_kernel()and that seems to work fine. So, it crashes silently somewhere after that point. I try to build 2.6.15-rc6-latest with kgbd support, not knowing if it's supposed to work on this platform.
It was a guess :)
Quoted 1 line
Are there some open issues from the
ppc->powerpcmigration?
possible, can you use git bisect to find what commit may have caused the issue?
- kumar
Hi,
Has the knowledge about this issue advanced?
What I have noticed so far is that the same happens in 2.6.14, therefore the problem rose in the transition from 2.6.13.
Would this be related to the IRQ stuff initialization? Any guess?
Quoted 35 lines · Kumar Gala
Quoted 13 lines · Clemens Koller
Hello!
Here is a little update:
Quoted 5 lines
I am just about to update my kernel from 2.6.13-rc7 which is working fine to linus' 2.6.15-rc5-latest git on my mpc8540ads flavored board. However, the kernel hangs pretty early after
openpic: exit
openpic_init()is called bympc85xx_ads_init_IRQin ppc/platforms/85xxppc_md.init_IRQ=mpc85xx_ads_init_IRQ in ppc/platforms/85xx
Quoted 7 lines
ppc_md.init_IRQ()is called frompowerpc/kernel/irq.c
init_IRQ()is called from init/main.c:start_kernel()and that seems to work fine. So, it crashes silently somewhere after that point. I try to build 2.6.15-rc6-latest with kgbd support, not knowing if it's supposed to work on this platform.
It was a guess :)
Quoted 1 line
Are there some open issues from the
ppc->powerpcmigration?possible, can you use git bisect to find what commit may have caused the issue?
- kumar
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Signature · 1 line
Carlos Mitidieri
Hi,
The kernel actually hangs when schedule() is called in rest_init() in main.c Would someone risk a guess ?
(keeping the walk...) Thanks,
Quoted 24 lines · Clemens Koller
Hello!
Here is a little update:
Quoted 5 lines
I am just about to update my kernel from 2.6.13-rc7 which is working fine to linus' 2.6.15-rc5-latest git on my mpc8540ads flavored board. However, the kernel hangs pretty early after
openpic: exit
openpic_init()is called bympc85xx_ads_init_IRQin ppc/platforms/85xxppc_md.init_IRQ=mpc85xx_ads_init_IRQ in ppc/platforms/85xx
ppc_md.init_IRQ()is called frompowerpc/kernel/irq.c
init_IRQ()is called from init/main.c:start_kernel()and that seems to work fine. So, it crashes silently somewhere after that point. I try to build 2.6.15-rc6-latest with kgbd support, not knowing if it's supposed to work on this platform.
Are there some open issues from the
ppc->powerpcmigration?Thanks,
Signature · 2 lines
Best regards, Carlos Mitidieri