Replacing 0xff.. with correct DMA_xBIT_MASK
Subsystems (16)
PATCH 1/1 Replacing 0xff.. with correct DMA_xBIT_MASK
From: Matthias Gehre
Included is a patch to replace all occurences of 0xff.. in calls to function pci_set_dma_mask() with the corresponding DMA_xBIT_MASK from linux/dma-mapping.h.
This patch was made against 2.6.15-rc4
Signed-off-by Matthias Gehre <[email protected]>
---
Task was found on janitor.kernelnewbies.org
Please CC answer to me.
Documentation/DMA-mapping.txt +2 -0
@@ -199,6 +199,8 @@ address during PCI bus mastering you mig "mydev: 24-bit DMA addressing not available.\n"); goto ignore_this_device; } +[Better use DMA_24BIT_MASK instead of 0x00ffffff. +See linux/include/dma-mapping.h for reference.] When pci_set_dma_mask() is successful, and returns zero, the PCI layer saves away this mask you have provided. The PCI layer will use this
drivers/block/umem.c +3 -2
@@ -50,6 +50,7 @@#include <linux/timer.h> #include <linux/pci.h> #include <linux/slab.h> +#include <linux/dma-mapping.h> #include <linux/fcntl.h> /* O_ACCMODE */ #include <linux/hdreg.h> /* HDIO_GETGEO */
@@ -892,8 +893,8 @@ static int __devinit mm_pci_probe(structprintk (KERN_INFO "Micro Memory(tm) controller #%d found at %02x:%02x (PCI Mem Module (Battery Backup))\n" , card->card_number, dev->bus->number, dev->devfn); -if (pci_set_dma_mask (dev,0xffffffffffffffffLL ) && - !pci_set_dma_mask (dev,0xffffffffLL )) { +if (pci_set_dma_mask (dev,DMA_64BIT_MASK ) && + !pci_set_dma_mask (dev,DMA_32BIT_MASK )) {printk (KERN_WARNING "MM%d: NO suitable DMA found\n" ,num_cards);return -ENOMEM ; }
drivers/net/forcedeth.c +2 -1
@@ -129,6 +129,7 @@#include <linux/random.h> #include <linux/init.h> #include <linux/if_vlan.h> +#include <linux/dma-mapping.h> #include <asm/irq.h> #include <asm/io.h>
@@ -2430,7 +2431,7 @@ static int __devinit nv_probe(struct pciif (id->driver_data &DEV_HAS_HIGH_DMA ) {/* packet format 3: supports 40-bit addressing */ np->desc_ver =DESC_VER_3 ; -if (pci_set_dma_mask (pci_dev,0x0000007fffffffffULL )) { +if (pci_set_dma_mask (pci_dev,DMA_39BIT_MASK )) {printk (KERN_INFO "forcedeth: 64-bit DMA failed, using 32-bit addressing for device %s.\n" ,pci_name (pci_dev)); }else {
drivers/net/ioc3-eth.c +3 -2
@@ -44,6 +44,7 @@#include <linux/ip.h> #include <linux/tcp.h> #include <linux/udp.h> +#include <linux/dma-mapping.h> #ifdef CONFIG_SERIAL_8250 #include <linux/serial_core.h>
@@ -1195,7 +1196,7 @@ static int ioc3_probe(struct pci_dev *pdint err, pci_using_dac;/* Configure DMA attributes. */ - err =pci_set_dma_mask (pdev,0xffffffffffffffffULL ); + err =pci_set_dma_mask (pdev,DMA_64BIT_MASK );if (!err) { pci_using_dac =1 ; err =pci_set_consistent_dma_mask (pdev,0xffffffffffffffffULL );
@@ -1205,7 +1206,7 @@ static int ioc3_probe(struct pci_dev *pd goto out; } }else { - err =pci_set_dma_mask (pdev,0xffffffffULL ); + err =pci_set_dma_mask (pdev,DMA_32BIT_MASK );if (err) {printk (KERN_ERR "%s: No usable DMA configuration, " "aborting.\n" ,pci_name (pdev));
drivers/net/ns83820.c +3 -3
@@ -1826,10 +1826,10 @@ static int __devinit ns83820_init_one(stint using_dac =0 ;/* See if we can set the dma mask early on; failure is fatal. */ -if (sizeof (dma_addr_t) ==8 && - !pci_set_dma_mask (pci_dev,0xffffffffffffffffULL )) { +if (sizeof (dma_addr_t) ==8 && + !pci_set_dma_mask (pci_dev,DMA_64BIT_MASK )) { using_dac =1 ; - }else if (!pci_set_dma_mask (pci_dev,0xffffffff )) { + }else if (!pci_set_dma_mask (pci_dev,DMA_32BIT_MASK )) { using_dac =0 ; }else {printk (KERN_WARNING "ns83820.c: pci_set_dma_mask failed!\n" );
drivers/net/wan/wanxl.c +2 -2
@@ -577,8 +577,8 @@ static int __devinit wanxl_pci_init_one(We set both dma_mask and consistent_dma_mask to 28 bits and pray pci_alloc_consistent() will use this info. It should work on most platforms */ -if (pci_set_consistent_dma_mask (pdev,0x0FFFFFFF ) || -pci_set_dma_mask (pdev,0x0FFFFFFF )) { +if (pci_set_consistent_dma_mask (pdev,DMA_28BIT_MASK ) || +pci_set_dma_mask (pdev,DMA_28BIT_MASK )) {printk (KERN_ERR "wanXL: No usable DMA configuration\n" );return -EIO ; }
drivers/net/wireless/prism54/islpci_hotplug.c +2 -1
@@ -22,6 +22,7 @@#include <linux/pci.h> #include <linux/delay.h> #include <linux/init.h> /* For __init, __exit */ +#include <linux/dma-mapping.h> #include "prismcompat.h" #include "islpci_dev.h"
@@ -124,7 +125,7 @@ prism54_probe(struct pci_dev *pdev, cons }/* enable PCI DMA */ -if (pci_set_dma_mask (pdev,0xffffffff )) { +if (pci_set_dma_mask (pdev,DMA_32BIT_MASK )) {printk (KERN_ERR "%s: 32-bit PCI DMA not supported" ,DRV_NAME ); goto do_pci_disable_device; }
drivers/scsi/a100u2w.c +2 -1
@@ -89,6 +89,7 @@#include <linux/string.h> #include <linux/ioport.h> #include <linux/slab.h> +#include <linux/dma-mapping.h> #include <asm/io.h> #include <asm/irq.h>
@@ -1052,7 +1053,7 @@ static int __devinit inia100_probe_one(sif (pci_enable_device (pdev)) goto out; -if (pci_set_dma_mask (pdev,0xffffffffULL )) { +if (pci_set_dma_mask (pdev,DMA_32BIT_MASK )) {printk (KERN_WARNING "Unable to set 32bit DMA " "on inia100 adapter, ignoring.\n" ); goto out_disable_device;
drivers/scsi/aacraid/linit.c +2 -1
@@ -49,6 +49,7 @@#include <linux/ioctl32.h> #include <linux/delay.h> #include <linux/smp_lock.h> +#include <linux/dma-mapping.h> #include <asm/semaphore.h> #include <scsi/scsi.h>
@@ -762,7 +763,7 @@ static int __devinit aac_probe_one(struc* to driver communication memory to be allocated below 2gig */ if (aac_drivers[index].quirks &AAC_QUIRK_31BIT ) -if (pci_set_dma_mask (pdev,0x7FFFFFFFULL ) || +if (pci_set_dma_mask (pdev,DMA_31BIT_MASK ) ||pci_set_consistent_dma_mask (pdev,0x7FFFFFFFULL )) goto out;
drivers/scsi/atp870u.c +2 -1
@@ -28,6 +28,7 @@#include <linux/spinlock.h> #include <linux/pci.h> #include <linux/blkdev.h> +#include <linux/dma-mapping.h> #include <asm/system.h> #include <asm/io.h>
@@ -2631,7 +2632,7 @@ static int atp870u_probe(struct pci_devif (pci_enable_device (pdev))return -EIO ; -if (!pci_set_dma_mask (pdev,0xFFFFFFFFUL )) { +if (!pci_set_dma_mask (pdev,DMA_32BIT_MASK )) {printk (KERN_INFO "atp870u: use 32bit DMA mask.\n" ); }else {printk (KERN_ERR "atp870u: DMA mask required but not available.\n" );
drivers/scsi/BusLogic.c +4 -3
@@ -41,6 +41,7 @@#include <linux/stat.h> #include <linux/pci.h> #include <linux/spinlock.h> +#include <linux/dma-mapping.h> #include <scsi/scsicam.h> #include <asm/dma.h>
@@ -676,7 +677,7 @@ static int __init BusLogic_InitializeMulif (pci_enable_device (PCI_Device))continue ; -if (pci_set_dma_mask (PCI_Device, (u64 )0xffffffff )) +if (pci_set_dma_mask (PCI_Device,DMA_32BIT_MASK ))continue ; Bus = PCI_Device->bus->number;
@@ -831,7 +832,7 @@ static int __init BusLogic_InitializeMulif (pci_enable_device (PCI_Device))continue ; -if (pci_set_dma_mask (PCI_Device, (u64 )0xffffffff )) +if (pci_set_dma_mask (PCI_Device,DMA_32BIT_MASK ))continue ; Bus = PCI_Device->bus->number;
@@ -885,7 +886,7 @@ static int __init BusLogic_InitializeFlaif (pci_enable_device (PCI_Device))continue ; -if (pci_set_dma_mask (PCI_Device, (u64 )0xffffffff )) +if (pci_set_dma_mask (PCI_Device,DMA_32BIT_MASK ))continue ; Bus = PCI_Device->bus->number;
drivers/scsi/dpt_i2o.c +3 -2
@@ -57,6 +57,7 @@ MODULE_DESCRIPTION("Adaptec I2O RAID Dri#include <linux/reboot.h> #include <linux/spinlock.h> #include <linux/smp_lock.h> +#include <linux/dma-mapping.h> #include <linux/timer.h> #include <linux/string.h>
@@ -884,8 +885,8 @@ static int adpt_install_hba(struct scsi_return -EINVAL ; }pci_set_master (pDev); -if (pci_set_dma_mask (pDev,0xffffffffffffffffULL ) && -pci_set_dma_mask (pDev,0xffffffffULL )) +if (pci_set_dma_mask (pDev,DMA_64BIT_MASK ) && +pci_set_dma_mask (pDev,DMA_32BIT_MASK ))return -EINVAL ; base_addr0_phys =pci_resource_start (pDev,0 );
drivers/scsi/eata.c +2 -1
@@ -490,6 +490,7 @@#include <linux/init.h> #include <linux/ctype.h> #include <linux/spinlock.h> +#include <linux/dma-mapping.h> #include <asm/byteorder.h> #include <asm/dma.h> #include <asm/io.h>
@@ -1426,7 +1427,7 @@ static int port_detect(unsigned long porif (ha->pdev) {pci_set_master (ha->pdev); -if (pci_set_dma_mask (ha->pdev,0xffffffff )) +if (pci_set_dma_mask (ha->pdev,DMA_32BIT_MASK ))printk ("%s: warning, pci_set_dma_mask failed.\n" , ha->board_name); }
drivers/scsi/gdth.c +4 -3
@@ -388,6 +388,7 @@#include <linux/proc_fs.h> #include <linux/time.h> #include <linux/timer.h> +#include <linux/dma-mapping.h> #ifdef GDTH_RTC #include <linux/mc146818rtc.h> #endif
@@ -4527,15 +4528,15 @@ static int __init gdth_detect(struct scsif (!(ha->cache_feat & ha->raw_feat & ha->screen_feat &GDT_64BIT )||/* 64-bit DMA only supported from FW >= x.43 */ (!ha->dma64_support)) { -if (pci_set_dma_mask (pcistr[ctr].pdev,0xffffffff )) { +if (pci_set_dma_mask (pcistr[ctr].pdev,DMA_32BIT_MASK )) {printk (KERN_WARNING "GDT-PCI %d: Unable to set 32-bit DMA\n" , hanum); err = TRUE; } }else { shp->max_cmd_len =16 ; -if (!pci_set_dma_mask (pcistr[ctr].pdev,0xffffffffffffffffULL )) { +if (!pci_set_dma_mask (pcistr[ctr].pdev,DMA_64BIT_MASK )) {printk ("GDT-PCI %d: 64-bit DMA enabled\n" , hanum); - }else if (pci_set_dma_mask (pcistr[ctr].pdev,0xffffffff )) { + }else if (pci_set_dma_mask (pcistr[ctr].pdev,DMA_32BIT_MASK )) {printk (KERN_WARNING "GDT-PCI %d: Unable to set 64/32-bit DMA\n" , hanum); err = TRUE; }
drivers/scsi/initio.c +2 -1
@@ -127,6 +127,7 @@#include <linux/sched.h> #include <linux/slab.h> #include <linux/jiffies.h> +#include <linux/dma-mapping.h> #include <asm/io.h> #include <scsi/scsi.h>
@@ -2780,7 +2781,7 @@ static int tul_NewReturnNumberOfAdaptersif (((dRegValue &0xFF00 ) >>8 ) ==0xFF ) dRegValue =0 ; wBIOS = (wBIOS <<8 ) + ((UWORD ) ((dRegValue &0xFF00 ) >>8 )); -if (pci_set_dma_mask (pDev,0xffffffff )) { +if (pci_set_dma_mask (pDev,DMA_32BIT_MASK )) {printk (KERN_WARNING "i91u: Could not set 32 bit DMA mask\n" );continue ;
drivers/scsi/ips.c +3 -2
@@ -179,6 +179,7 @@#include <linux/blkdev.h> #include <linux/types.h> +#include <linux/dma-mapping.h> #include <scsi/sg.h>
@@ -7279,10 +7280,10 @@ ips_init_phase1(struct pci_dev *pci_dev,* are guaranteed to be < 4G. */ if (IPS_ENABLE_DMA64 &&IPS_HAS_ENH_SGLIST (ha) && - !pci_set_dma_mask (ha->pcidev,0xffffffffffffffffULL )) { + !pci_set_dma_mask (ha->pcidev,DMA_64BIT_MASK )) { (ha)->flags |=IPS_HA_ENH_SG ; }else { -if (pci_set_dma_mask (ha->pcidev,0xffffffffULL ) !=0 ) { +if (pci_set_dma_mask (ha->pcidev,DMA_32BIT_MASK ) !=0 ) {printk (KERN_WARNING "Unable to set DMA Mask\n" );return ips_abort_init (ha, index); }
drivers/scsi/megaraid.c +4 -3
@@ -44,6 +44,7 @@#include <linux/interrupt.h> #include <linux/pci.h> #include <linux/init.h> +#include <linux/dma-mapping.h> #include <scsi/scsicam.h> #include "scsi.h"
@@ -2093,7 +2094,7 @@ make_local_pdev(adapter_t *adapter, strumemcpy (*pdev, adapter->dev,sizeof (struct pci_dev )); -if (pci_set_dma_mask (*pdev,0xffffffff ) !=0 ) { +if (pci_set_dma_mask (*pdev,DMA_32BIT_MASK ) !=0 ) {kfree (*pdev);return -1 ; }
@@ -4858,10 +4859,10 @@ megaraid_probe_one(struct pci_dev *pdev,/* Set the Mode of addressing to 64 bit if we can */ if ((adapter->flag &BOARD_64BIT ) && (sizeof (dma_addr_t) ==8 )) { -pci_set_dma_mask (pdev,0xffffffffffffffffULL ); +pci_set_dma_mask (pdev,DMA_64BIT_MASK ); adapter->has_64bit_addr =1 ; }else { -pci_set_dma_mask (pdev,0xffffffff ); +pci_set_dma_mask (pdev,DMA_32BIT_MASK ); adapter->has_64bit_addr =0 ; }
drivers/scsi/nsp32.c +2 -1
@@ -38,6 +38,7 @@#include <linux/pci.h> #include <linux/delay.h> #include <linux/ctype.h> +#include <linux/dma-mapping.h> #include <asm/dma.h> #include <asm/system.h>
@@ -2776,7 +2777,7 @@ static int nsp32_detect(struct scsi_host/* * setup DMA */ -if (pci_set_dma_mask (PCIDEV ,0xffffffffUL ) !=0 ) { +if (pci_set_dma_mask (PCIDEV ,DMA_32BIT_MASK ) !=0 ) {nsp32_msg (KERN_ERR ,"failed to set PCI DMA mask" ); goto scsi_unregister; }
drivers/scsi/qla1280.c +3 -2
@@ -348,6 +348,7 @@#include <linux/pci_ids.h> #include <linux/interrupt.h> #include <linux/init.h> +#include <linux/dma-mapping.h> #include <asm/io.h> #include <asm/irq.h>
@@ -4569,7 +4570,7 @@ qla1280_probe_one(struct pci_dev *pdev,#ifdef QLA_64BIT_PTR if (pci_set_dma_mask (ha->pdev, (dma_addr_t ) ~0ULL )) { -if (pci_set_dma_mask (ha->pdev,0xffffffff )) { +if (pci_set_dma_mask (ha->pdev,DMA_32BIT_MASK )) {printk (KERN_WARNING "scsi(%li): Unable to set a " "suitable DMA mask - aborting\n" , ha->host_no); error = -ENODEV ;
@@ -4579,7 +4580,7 @@ qla1280_probe_one(struct pci_dev *pdev,dprintk (2 ,"scsi(%li): 64 Bit PCI Addressing Enabled\n" , ha->host_no);#else -if (pci_set_dma_mask (ha->pdev,0xffffffff )) { +if (pci_set_dma_mask (ha->pdev,DMA_32BIT_MASK )) {printk (KERN_WARNING "scsi(%li): Unable to set a " "suitable DMA mask - aborting\n" , ha->host_no); error = -ENODEV ;
drivers/scsi/qlogicfc.c +3 -2
@@ -61,6 +61,7 @@#include <linux/unistd.h> #include <linux/spinlock.h> #include <linux/interrupt.h> +#include <linux/dma-mapping.h> #include <asm/io.h> #include <asm/irq.h> #include "scsi.h"
@@ -737,8 +738,8 @@ static int isp2x00_detect(struct scsi_hocontinue ;/* Try to configure DMA attributes. */ -if (pci_set_dma_mask (pdev,0xffffffffffffffffULL ) && -pci_set_dma_mask (pdev,0xffffffffULL )) +if (pci_set_dma_mask (pdev,DMA_64BIT_MASK ) && +pci_set_dma_mask (pdev,DMA_32BIT_MASK ))continue ; host =scsi_register (tmpt,sizeof (struct isp2x00_hostdata ));
include/linux/dma-mapping.h +2 -0
@@ -20,6 +20,8 @@ enum dma_data_direction {#define DMA_31BIT_MASK 0x000000007fffffffULL#define DMA_30BIT_MASK 0x000000003fffffffULL#define DMA_29BIT_MASK 0x000000001fffffffULL +#define DMA_28BIT_MASK 0x000000000fffffffULL +#define DMA_24BIT_MASK 0x0000000000ffffffULL#include <asm/dma-mapping.h>
sound/oss/esssolo1.c +1 -1
@@ -2346,7 +2346,7 @@ static int __devinit solo1_probe(struct/* Recording requires 24-bit DMA, so attempt to set dma mask * to 24 bits first, then 32 bits (playback only) if that fails. */ -if (pci_set_dma_mask (pcidev,0x00ffffff ) && +if (pci_set_dma_mask (pcidev,DMA_24BIT_MASK ) &&pci_set_dma_mask (pcidev,DMA_32BIT_MASK )) {printk (KERN_WARNING "solo1: architecture does not support 24bit or 32bit PCI busmaster DMA\n" );return -ENODEV ;
sound/oss/sonicvibes.c +2 -1
@@ -116,6 +116,7 @@#include <linux/spinlock.h> #include <linux/smp_lock.h> #include <linux/gameport.h> +#include <linux/dma-mapping.h> #include <asm/io.h> #include <asm/uaccess.h>
@@ -2551,7 +2552,7 @@ static int __devinit sv_probe(struct pcireturn -ENODEV ;if (pcidev->irq ==0 )return -ENODEV ; -if (pci_set_dma_mask (pcidev,0x00ffffff )) { +if (pci_set_dma_mask (pcidev,DMA_24BIT_MASK )) {printk (KERN_WARNING "sonicvibes: architecture does not support 24bit PCI busmaster DMA\n" );return -ENODEV ; }
sound/pci/ad1889.c +3 -2
@@ -38,6 +38,7 @@#include <linux/interrupt.h> #include <linux/compiler.h> #include <linux/delay.h> +#include <linux/dma-mapping.h> #include <sound/driver.h> #include <sound/core.h>
@@ -920,8 +921,8 @@ snd_ad1889_create(snd_card_t *card,return err;/* check PCI availability (32bit DMA) */ -if (pci_set_dma_mask (pci,0xffffffff ) <0 || -pci_set_consistent_dma_mask (pci,0xffffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_32BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_32BIT_MASK ) <0 ) { printk(KERN_ERR PFX "error setting 32-bit DMA mask.\n");pci_disable_device (pci);return -ENXIO ;
sound/pci/ali5451/ali5451.c +3 -2
@@ -33,6 +33,7 @@#include <linux/pci.h> #include <linux/slab.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/pcm.h> #include <sound/info.h>
@@ -2237,8 +2238,8 @@ static int __devinit snd_ali_create(snd_if ((err =pci_enable_device (pci)) <0 )return err;/* check, if we can restrict PCI DMA transfers to 31 bits */ -if (pci_set_dma_mask (pci,0x7fffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x7fffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_31BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_31BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 31bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/als4000.c +3 -2
@@ -65,6 +65,7 @@#include <linux/slab.h> #include <linux/gameport.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/pcm.h> #include <sound/rawmidi.h>
@@ -665,8 +666,8 @@ static int __devinit snd_card_als4000_prreturn err; }/* check, if we can restrict PCI DMA transfers to 24 bits */ -if (pci_set_dma_mask (pci,0x00ffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x00ffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_24BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_24BITMASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 24bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/azt3328.c +3 -2
@@ -104,6 +104,7 @@#include <linux/slab.h> #include <linux/gameport.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/control.h> #include <sound/pcm.h>
@@ -1672,8 +1673,8 @@ snd_azf3328_create(snd_card_t * card, chip->irq =-1 ;/* check if we can restrict PCI DMA transfers to 24 bits */ -if (pci_set_dma_mask (pci,0x00ffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x00ffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_24BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_24BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 24bit PCI busmaster DMA\n" ); err = -ENXIO ; goto out_err;
sound/pci/emu10k1/emu10k1x.c +3 -2
@@ -35,6 +35,7 @@#include <linux/pci.h> #include <linux/slab.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/initval.h> #include <sound/pcm.h>
@@ -911,8 +912,8 @@ static int __devinit snd_emu10k1x_createif ((err =pci_enable_device (pci)) <0 )return err; -if (pci_set_dma_mask (pci,0x0fffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x0fffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_28BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_28BIT_MASK ) <0 ) {snd_printk (KERN_ERR "error to set 28bit mask DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/es1938.c +3 -2
@@ -55,6 +55,7 @@#include <linux/gameport.h> #include <linux/moduleparam.h> #include <linux/delay.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/control.h> #include <sound/pcm.h>
@@ -1499,8 +1500,8 @@ static int __devinit snd_es1938_create(sif ((err =pci_enable_device (pci)) <0 )return err;/* check, if we can restrict PCI DMA transfers to 24 bits */ -if (pci_set_dma_mask (pci,0x00ffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x00ffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_24BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_24BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 24bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/es1968.c +3 -2
@@ -103,6 +103,7 @@#include <linux/slab.h> #include <linux/gameport.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/pcm.h> #include <sound/mpu401.h>
@@ -2560,8 +2561,8 @@ static int __devinit snd_es1968_create(sif ((err =pci_enable_device (pci)) <0 )return err;/* check, if we can restrict PCI DMA transfers to 28 bits */ -if (pci_set_dma_mask (pci,0x0fffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x0fffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_28BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_28BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 28bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/ice1712/ice1712.c +3 -2
@@ -55,6 +55,7 @@#include <linux/pci.h> #include <linux/slab.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/cs8427.h> #include <sound/info.h>
@@ -2522,8 +2523,8 @@ static int __devinit snd_ice1712_create(if ((err =pci_enable_device (pci)) <0 )return err;/* check, if we can restrict PCI DMA transfers to 28 bits */ -if (pci_set_dma_mask (pci,0x0fffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x0fffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_28BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_28BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 28bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/maestro3.c +3 -2
@@ -40,6 +40,7 @@#include <linux/slab.h> #include <linux/vmalloc.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/info.h> #include <sound/control.h>
@@ -2651,8 +2652,8 @@ snd_m3_create(snd_card_t *card, struct preturn -EIO ;/* check, if we can restrict PCI DMA transfers to 28 bits */ -if (pci_set_dma_mask (pci,0x0fffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x0fffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_28BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_28BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 28bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/mixart/mixart.c +2 -1
@@ -26,6 +26,7 @@#include <linux/interrupt.h> #include <linux/pci.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/initval.h> #include <sound/info.h>
@@ -1283,7 +1284,7 @@ static int __devinit snd_mixart_probe(stpci_set_master (pci);/* check if we can restrict PCI DMA transfers to 32 bits */ -if (pci_set_dma_mask (pci,0xffffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_32BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 32bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/sonicvibes.c +3 -2
@@ -30,6 +30,7 @@#include <linux/slab.h> #include <linux/gameport.h> #include <linux/moduleparam.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/pcm.h>
@@ -1237,8 +1238,8 @@ static int __devinit snd_sonicvibes_creaif ((err =pci_enable_device (pci)) <0 )return err;/* check, if we can restrict PCI DMA transfers to 24 bits */ -if (pci_set_dma_mask (pci,0x00ffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x00ffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_24BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_24BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 24bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
sound/pci/trident/trident_main.c +5 -4
@@ -35,6 +35,7 @@#include <linux/slab.h> #include <linux/vmalloc.h> #include <linux/gameport.h> +#include <linux/dma-mapping.h> #include <sound/core.h> #include <sound/info.h>
@@ -3539,8 +3540,8 @@ int __devinit snd_trident_create(snd_carif ((err =pci_enable_device (pci)) <0 )return err;/* check, if we can restrict PCI DMA transfers to 30 bits */ -if (pci_set_dma_mask (pci,0x3fffffff ) <0 || -pci_set_consistent_dma_mask (pci,0x3fffffff ) <0 ) { +if (pci_set_dma_mask (pci,DMA_30BIT_MASK ) <0 || +pci_set_consistent_dma_mask (pci,DMA_30BIT_MASK ) <0 ) {snd_printk (KERN_ERR "architecture does not support 30bit PCI busmaster DMA\n" );pci_disable_device (pci);return -ENXIO ;
@@ -3949,8 +3950,8 @@ static int snd_trident_resume(snd_card_ttrident_t *trident = card->pm_private_data;pci_enable_device (trident->pci); -if (pci_set_dma_mask (trident->pci,0x3fffffff ) <0 || -pci_set_consistent_dma_mask (trident->pci,0x3fffffff ) <0 ) +if (pci_set_dma_mask (trident->pci,DMA_30BIT_MASK ) <0 || +pci_set_consistent_dma_mask (trident->pci,DMA_30BIT_MASK ) <0 )snd_printk (KERN_WARNING "trident: can't set the proper DMA mask\n" );pci_set_master (trident->pci);/* to be sure */