fc transport recursion depth exceeded
Hi James,
I was testing with the qlogic board this afternoon and observed these messages in the dmesg output. They were generated in response to a switchdisable ; sleep 5 ; switchenable command sequence on my switch.
end_request: I/O error, dev sdbz, sector 1282218
sd 4:0:34:0: SCSI error: return code = 0x10000run_workqueue: recursion depth exceeded: 4
Call Trace:
end_request: I/O error, dev sdbz, sector 1282250
[<a000000100012ae0>] show_stack+0x40/0xa0
sp=e0000034f6a8f9e0 bsp=e0000034f6a894c0
sd 4:0:34:0: SCSI error: return code = 0x10000
end_request: I/O error, dev sdbz, sector 1282282
[<a000000100012b70>] dump_stack+0x30/0x60
sp=e0000034f6a8fbb0 bsp=e0000034f6a894a8
[<a0000001000c8f10>] run_workqueue+0x90/0x280
sp=e0000034f6a8fbb0 bsp=e0000034f6a89468
[<a0000001000c9150>] flush_cpu_workqueue+0x50/0x1e0
sp=e0000034f6a8fbb0 bsp=e0000034f6a89438
[<a0000001000c9350>] flush_workqueue+0x70/0x160
sp=e0000034f6a8fc10 bsp=e0000034f6a89410
[<a00000010052b130>] scsi_flush_work+0x90/0xc0
sp=e0000034f6a8fc10 bsp=e0000034f6a893e8
[<a000000100547480>] fc_rport_tgt_remove+0x100/0x140
sp=e0000034f6a8fc10 bsp=e0000034f6a893b8
[<a0000001005475b0>] fc_shost_remove_rports+0xf0/0x1c0
sp=e0000034f6a8fc10 bsp=e0000034f6a89388
[<a0000001000c9040>] run_workqueue+0x1c0/0x280
sp=e0000034f6a8fc10 bsp=e0000034f6a89348
[<a0000001000c9150>] flush_cpu_workqueue+0x50/0x1e0
sp=e0000034f6a8fc10 bsp=e0000034f6a89318
[<a0000001000c9350>] flush_workqueue+0x70/0x160
sp=e0000034f6a8fc70 bsp=e0000034f6a892f0
[<a00000010052b130>] scsi_flush_work+0x90/0xc0
sp=e0000034f6a8fc70 bsp=e0000034f6a892d0
[<a000000100547480>] fc_rport_tgt_remove+0x100/0x140
sp=e0000034f6a8fc70 bsp=e0000034f6a892a0
[<a0000001005475b0>] fc_shost_remove_rports+0xf0/0x1c0
sp=e0000034f6a8fc70 bsp=e0000034f6a89270
[<a0000001000c9040>] run_workqueue+0x1c0/0x280
sp=e0000034f6a8fc70 bsp=e0000034f6a89230
[<a0000001000c9150>] flush_cpu_workqueue+0x50/0x1e0
sp=e0000034f6a8fc70 bsp=e0000034f6a89200
[<a0000001000c9350>] flush_workqueue+0x70/0x160
sp=e0000034f6a8fcd0 bsp=e0000034f6a891d0
[<a00000010052b130>] scsi_flush_work+0x90/0xc0
sp=e0000034f6a8fcd0 bsp=e0000034f6a891b0
[<a000000100547480>] fc_rport_tgt_remove+0x100/0x140
sp=e0000034f6a8fcd0 bsp=e0000034f6a89180
[<a0000001005475b0>] fc_shost_remove_rports+0xf0/0x1c0
sp=e0000034f6a8fcd0 bsp=e0000034f6a89150
[<a0000001000c9040>] run_workqueue+0x1c0/0x280
sp=e0000034f6a8fcd0 bsp=e0000034f6a89110
[<a0000001000ca130>] worker_thread+0x1d0/0x260
sp=e0000034f6a8fcd0 bsp=e0000034f6a890e0
[<a0000001000d1f00>] kthread+0x220/0x2a0
sp=e0000034f6a8fd50 bsp=e0000034f6a89098
[<a000000100011070>] kernel_thread_helper+0xd0/0x100
sp=e0000034f6a8fe30 bsp=e0000034f6a89070
[<a000000100009120>] start_kernel_thread+0x20/0x40
sp=e0000034f6a8fe30 bsp=e0000034f6a89070sd 3:0:35:0: SCSI error: return code = 0x10000end_request: I/O error, dev sdcr, sector 1745339
sd 6:0:33:0: SCSI error: return code = 0x10000end_request: I/O error, dev sdek, sector 2880792
This happened a number of times during the single test event.
Mike