irq balance problems?
hi
i have kernel 2.6.9, with FC2, on an AMD64 Dual Opteron.
[root@btv 28]# cat /proc/interrupts
CPU0 CPU1
0: 22249515 39262513 IO-APIC-edge timer 1: 0 8 IO-APIC-edge i8042 2: 0 0 XT-PIC cascade 8: 0 0 IO-APIC-edge rtc 14: 1 13 IO-APIC-edge ide0 24: 10 441422068 IO-APIC-level ioc0, eth1 25: 171765170 5905 IO-APIC-level ioc1, eth2 28: 921 406066 IO-APIC-level eth0 NMI: 16960 6317 LOC: 61500529 61500464 ERR: 0 MIS: 0
i was wondering, if IRQ28's (eth0) affinity is set to the default "f"
[root@btv 28]# cat /proc/irq/prof_cpu_mask
f
[root@btv 28]# cat /proc/irq/28/smp_affinity
f
and irqbalance is not running, why aren't the interrupts coming from eth0 balanced between the two processors? at least that's what i understood from the examples in Documentation/IRQ-affinity.txt. are there any other settings/kernel parameters/compile option one has to set?
(pls msg me in private, i'm not on the list.)
thanks
Quoted 5 lines
and irqbalance is not running, why aren't the interrupts coming from eth0 balanced between the two processors? at least that's what i understood from the examples in
Documentation/IRQ-affinity.txt. are there any other settings/kernel parameters/compile option one has to set?
it'll depend on the chipset. Some round-robin, some don't. For performance it's better to not round-robin.
Quoted 7 lines · Arjan van de Ven
Quoted 4 lines
and irqbalance is not running, why aren't the interrupts coming from eth0 balanced between the two processors? at least that's what i understood from the examples in
Documentation/IRQ-affinity.txt. are there any other settings/kernel parameters/compile option one has to set?it'll depend on the chipset. Some round-robin, some don't. For performance it's better to not round-robin.
is there a way to see for sure? or this behaviour is proof enough that it doesn't do round-robin?
Quoted 7 lines · Imre Gergely
Quoted 5 lines · Arjan van de Ven
Quoted 4 lines
and irqbalance is not running, why aren't the interrupts coming from eth0 balanced between the two processors? at least that's what i understood from the examples in
Documentation/IRQ-affinity.txt. are there any other settings/kernel parameters/compile option one has to set?
Quoted 5 lines
Quoted 2 lines
it'll depend on the chipset. Some round-robin, some don't. For performance it's better to not round-robin.
is there a way to see for sure? or this behaviour is proof enough that it doesn't do round-robin?
it's pretty much proof to me already yes ;)
(but why do you want round-robin? it's the worst setting for performance..... )
Quoted 8 lines · Arjan van de Ven
Quoted 7 lines · Imre Gergely
Quoted 6 lines · Arjan van de Ven
Quoted 4 lines
and irqbalance is not running, why aren't the interrupts coming from eth0 balanced between the two processors? at least that's what i understood from the examples in
Documentation/IRQ-affinity.txt. are there any other settings/kernel parameters/compile option one has to set?it'll depend on the chipset. Some round-robin, some don't. For performance it's better to not round-robin.
Quoted 7 lines
Quoted 2 lines
is there a way to see for sure? or this behaviour is proof enough that it doesn't do round-robin?
it's pretty much proof to me already yes ;)
(but why do you want round-robin? it's the worst setting for performance..... )
on one of the ethernet cards is much traffic, and there is htb (with many classes and filters) used. because of this, one CPU is always on 95-100%, the other is barely used. i wanted to see if it would improve performance if it did balancing between the CPUs.