Skip to contentSkip to conversation

I/O error

linux-lvm German Staltari 3 participants 4 messages Mar 13, 2006 – Mar 15, 2006

lore
Share & tools
lore
#0 lore raw

Hi, we have an IBM server attached to an IBM SAN with a qlogic HBA. When I run 'lvdisplay' or any other 'Xdisplay' (vg, pv) command this is the output:

/dev/sdq: read failed after 0 of 4096 at 0: Input/output error /dev/sdb: read failed after 0 of 4096 at 0: Input/output error /dev/sds: read failed after 0 of 4096 at 0: Input/output error /dev/sdd: read failed after 0 of 4096 at 0: Input/output error /dev/sdt: read failed after 0 of 4096 at 0: Input/output error Found duplicate PV DYM8ElmyYadLJeAJk5TfxMx7pprrFHfk: using /dev/sdu
not /dev/sdc
/dev/sdf: read failed after 0 of 4096 at 0: Input/output error /dev/sdv: read failed after 0 of 4096 at 0: Input/output error Found duplicate PV Qoe4208RQKg0XK1AfXjInMLglzU8ks6v: using /dev/sdw
not /dev/sde
/dev/sdh: read failed after 0 of 4096 at 0: Input/output error /dev/sdx: read failed after 0 of 4096 at 0: Input/output error Found duplicate PV n3IC77zXPw0QQ6OcfldMfpKPRG3QsxXW: using /dev/sdy
not /dev/sdi
Found duplicate PV EX7OrzfwKADyFhnnlooYEKtvL9t5Gv3W: using /dev/sdj
not /dev/sdg
/dev/sdk: read failed after 0 of 4096 at 0: Input/output error /dev/sdm: read failed after 0 of 4096 at 0: Input/output error Found duplicate PV ftppICdxAujdcPH0eZ77TBWD6waiOckd: using /dev/sdn
not /dev/sdl
Found duplicate PV OuTEiF4W1rYuVGOTEcKQQmrDnDkpyATT: using /dev/sdp
not /dev/sdr
------------------------------ cut -----------------------------------------

The Storage Admin told me that there are two path to the same storage (disk). I would like to know if this is an error to be worried about or is just info? And if there's a way to avoid this output. Also, when a I run 'dmesg', I have this output (if I clear with 'dmesg -c', it will appear again in the next minutes):

Buffer I/O error on device sdk, logical block 0
end_request: I/O error, dev sdk, sector 0 Buffer I/O error on device sdk, logical block 0
end_request: I/O error, dev sdm, sector 0
end_request: I/O error, dev sdm, sector 0
printk: 1 messages suppressed.
Buffer I/O error on device sdm, logical block 0
end_request: I/O error, dev sdq, sector 0
end_request: I/O error, dev sdq, sector 0
end_request: I/O error, dev sds, sector 0

FC4
kernel-smp-2.6.15-1.1831_FC4
LVM version: 2.01.08 (2005-03-22)
Library version: 1.01.02 (2005-05-17)
Driver version: 4.4.0
Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev 02)

Thanks
German Staltari

#1 lore raw
Quoted 1 line · German Staltari

The Storage Admin told me that there are two path to the same storage (disk). I would like to know if this is an error to be worried about or is just info? And if there's a way to avoid this output. Also, when a I run 'dmesg', I have this output (if I clear with 'dmesg -c', it will appear again in the next minutes):

You might want to download QLogic's drivers for the card, and build them with multipath support.. then you'll only see the drives once, and it should hopefully clear out these errors for you.

(The multipath driver used to be included in the qlogic drivers in the kernel, but were removed for some reason I Don't recall..)

------------------------------------------------------------------------

| nate carlson | [email protected] | http://www.natecarlson.com |
|       depriving some poor village of its idiot since 1981            |

------------------------------------------------------------------------

#2 lore raw
Quoted 3 lines · Nate Carlson

You might want to download QLogic's drivers for the card, and build them with multipath support.. then you'll only see the drives once, and it should hopefully clear out these errors for you.

(The multipath driver used to be included in the qlogic drivers in the kernel, but were removed for some reason I Don't recall..)

probably because multipath-tools is a cleaner solution?

L.

Signature · 6 lines
Luca Berra -- [email protected]
       Communication Media & Services S.r.l.
/"\
\ /     ASCII RIBBON CAMPAIGN
 X        AGAINST HTML MAIL
/ \
#3 lore raw
Quoted 1 line · Luca Berra

probably because multipath-tools is a cleaner solution?

Hmm.. hadn't run into this one before; looked over the docs.. looks interesting, and very flexible, but also a heck of a lot more complicated. :)

------------------------------------------------------------------------

| nate carlson | [email protected] | http://www.natecarlson.com |
|       depriving some poor village of its idiot since 1981            |

------------------------------------------------------------------------