Skip to contentSkip to conversation

Modify the usb power budget in OSK?

DISCUSSION Li Weichen 3 participants 3 messages Mar 20, 2006 – Mar 25, 2006

lore
Share & tools
lore

Li Weichen

author
#0 lore raw

Hi all,

I am trying to plug a D-Link DWL-G122 802.11g wlan usb stick on to OSK. But I always get the "over power budget" warning, should I modify the power budget set in drivers/usb/host/ohci-omap.c? Has anyone ever succeeded to utilize a similar usb stick?

And, I have tried to use a extra wire to get power supply from a PC usb port, the errors were still.

I am so eagerly looking forward to your help, thank you in advance.

Best regards!

Li Weichen

#1 lore raw

Re: Modify the usb power budget in OSK

Hello,

We have the same problem with our web camera... We're using an external power supply for USB.

First, we modified the line in ohci-omap.c
ohci_to_hcd(ohci)->power_budget = 250;
to
ohci_to_hcd(ohci)->power_budget = 500;

After that modification, during the boot process, we still got the message "400mA over 100mA budget"
By searching the files containing string "mA budget", we have found inside hub.c

		/* 100mA per-port ceiling, or 8mA for OTG ports */
		if (i != (udev->bus->otg_port - 1) || hdev->parent)
			ceiling = 50;
		else
			ceiling = 4;

In the rest of the source, the value 'ceiling' is considered as a half the maximum power that the USB port can give. After modifying the 'ceiling' value from 50 (which corresponds to 100mA) to 250 (corresponds to 500mA) we didn't have the boot message mentioned anymore, but the camera still doesn't work, nor its LED :( But, you might give a try with this.

It looks strange to me that hub.c is even needed, as well as there is 100mA limit inside of it. We still doubt that our camera doesn't work due to some power budget-related issue. Is something else to be modified?

TIA
Djordje Nijemcevic

Quoted 23 lines

Hi all,

I am trying to plug a D-Link DWL-G122 802.11g wlan usb stick on to OSK. But
I always get the "over power budget" warning, should I modify the power budget set in drivers/usb/host/ohci-omap.c? Has anyone ever succeeded to utilize a similar usb stick?

And, I have tried to use a extra wire to get power supply from a PC usb port, the errors were still.

I am so eagerly looking forward to your help, thank you in advance.

Best regards!

Li Weichen

_______________________________________________
Linux-omap-open-source mailing list
[email protected]
http://linux.omap.com/mailman/listinfo/linux-omap-open-source

#2 lore raw

Re: Modify the usb power budget in OSK

Hello,
I still have "over budget" message annoying me, but my cameras started to work then I compiled all the modules into the kernel and stopped using modprobe or insmod modules.
You can try the following:

Device Drivers --->
Multimedia deices --->
<*> Video for Linux ( CONFIG_VIDEO_DEV )

Device Drivers --->
USB support --->
<*> Support for Host-side USB ( CONFIG_USB )
<*> OHCI HCD support ( CONFIG_USB_OHCI_HCD )

Device Drivers --->
USB support --->
USB Camera support-->
<*> USB SN9C10x PC Camera Controler support ( CONFIG_USB_SN9C102 )

Madis

Quoted 70 lines · Djordje Nijemcevic

Hello,

We have the same problem with our web camera... We're using an external power supply for USB.

First, we modified the line in ohci-omap.c
ohci_to_hcd(ohci)->power_budget = 250;
to
ohci_to_hcd(ohci)->power_budget = 500;

After that modification, during the boot process, we still got the message "400mA over 100mA budget"
By searching the files containing string "mA budget", we have found inside hub.c

		/* 100mA per-port ceiling, or 8mA for OTG ports */
		if (i != (udev->bus->otg_port - 1) || hdev->parent)
			ceiling = 50;
		else
			ceiling = 4;

In the rest of the source, the value 'ceiling' is considered as a half the maximum power that the USB port can give. After modifying the 'ceiling' value from 50 (which corresponds to 100mA) to 250 (corresponds to 500mA) we didn't have the boot message mentioned anymore, but the camera still doesn't work, nor its LED :( But, you might give a try with this.

It looks strange to me that hub.c is even needed, as well as there is 100mA limit inside of it. We still doubt that our camera doesn't work due to some power budget-related issue. Is something else to be modified?

TIA
Djordje Nijemcevic

Quoted 16 lines

Hi all,

I am trying to plug a D-Link DWL-G122 802.11g wlan usb stick on to OSK. But
I always get the "over power budget" warning, should I modify the power budget set in drivers/usb/host/ohci-omap.c? Has anyone ever succeeded to utilize a similar usb stick?

And, I have tried to use a extra wire to get power supply from a PC usb port, the errors were still.

I am so eagerly looking forward to your help, thank you in advance.

Best regards!

Quoted 9 lines

Li Weichen

_______________________________________________
Linux-omap-open-source mailing list
[email protected]
http://linux.omap.com/mailman/listinfo/linux-omap-open-source

_______________________________________________
Linux-omap-open-source mailing list
[email protected]
http://linux.omap.com/mailman/listinfo/linux-omap-open-source