Skip to contentSkip to conversation

fix MMC response types

PATCH New Carlos Aguiar 1 participant 1 message Mar 27, 2006 MMC, SD and SDIO

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 fix MMC response types

Ok, let's try again, now with the patch...

Hi Andrzej and folks,

Attached to this mail follow my propose of fixing MMC responde types in mmc_omap_start_command().

This is based on the patches of the thread '[RFC] mmc: add OMAP driver' that I sent to LKML mailing-list in order to have integrated the MMC OMAP driver on the mainline kernel.

Comments and suggestions are welcome.

BR,

Carlos.

Signature · 7 lines
Carlos Eduardo
Software Engineer
Nokia Institute of Technology - INdT
Embedded Linux Laboratory - 10LE
Phone: +55 92 2126-1079
Mobile: +55 92 8127-1797
E-mail: [email protected]
drivers/mmc/omap.c +18 -26
Index: linux-omap-2.6.git/drivers/mmc/omap.c
===================================================================
@@ -49,6 +49,7 @@
 #include "omap.h"
 
 #define DRIVER_NAME "mmci-omap"
+#define RSP_TYPE(x)	((x) & ~(MMC_RSP_BUSY|MMC_RSP_OPCODE))
 
 #ifdef CONFIG_MMC_DEBUG
 #define DBG(x...)	pr_debug(x)
@@ -185,36 +186,27 @@ mmc_omap_start_command(struct mmc_omap_h
 		host->hw_bus_mode = host->bus_mode;
 	}
 
-	if (!(cmd->flags & MMC_RSP_PRESENT))
-		resptype = 0;			/* Resp 0 */
-
-	if (cmd->flags & MMC_RSP_136)
-		resptype = 2;			/* Resp 2 */
-	else {
-		if (host->bus_mode == MMC_BUSMODE_OPENDRAIN)
-			resptype = 3;		/* Resp 3 */
-		else
-			resptype = 1;		/* Resp 1, Resp 1b */
+	/* Our hardware needs to know exact type */
+	switch (RSP_TYPE(mmc_resp_type(cmd))) {
+	case RSP_TYPE(MMC_RSP_R1):
+		/* resp 1, resp 1b */
+		resptype = 1;
+		break;
+	case RSP_TYPE(MMC_RSP_R2):
+		resptype = 2;
+		break;
+	case RSP_TYPE(MMC_RSP_R3):
+		resptype = 3;
+		break;
+	default:
+		break;
 	}
 
-	/* Protocol layer does not provide command type, but our hardware
-	 * needs it!
-	 * any data transfer means adtc type (but that information is not
-	 * in command structure, so we flagged it into host struct.)
-	 * However, telling bc, bcr and ac apart based on response is
-	 * not foolproof:
-	 * CMD0  = bc  = resp0  CMD15 = ac  = resp0
-	 * CMD2  = bcr = resp2  CMD10 = ac  = resp2
-	 *
-	 * Resolve to best guess with some exception testing:
-	 * resp0 -> bc, except CMD15 = ac
-	 * rest are ac, except if opendrain
-	 */
-	if (host->data) {
+	if (mmc_cmd_type(cmd) == MMC_CMD_ADTC) {
 		cmdtype = OMAP_MMC_CMDTYPE_ADTC;
-	} else if (resptype == 0 && cmd->opcode != 15) {
+	} else if (mmc_cmd_type(cmd) == MMC_CMD_BC) {
 		cmdtype = OMAP_MMC_CMDTYPE_BC;
-	} else if (host->bus_mode == MMC_BUSMODE_OPENDRAIN) {
+	} else if (mmc_cmd_type(cmd) == MMC_CMD_BCR) {
 		cmdtype = OMAP_MMC_CMDTYPE_BCR;
 	} else {
 		cmdtype = OMAP_MMC_CMDTYPE_AC;