3w-9xxx status in kernel
Hi,
I have a question about 3w-9xxx driver versions :
3w-9xxx version in vanilla 2.6.16 is 2.26.02.005
3w-9xxx version in 2.6.17-rc1-mm2 is 2.26.02.006
but :
3w-9xxx version in 3ware.com 9.3.0.3 codebase is 2.26.04.007
The documentation with 9.3.0.3 codebase says it will not works with kernel driver <2.26.04.004. But I observe it works fine with codebase 9.3.0.2 (the documentation says it should not).
What is current status of 3w-9xxx driver in 2.6 ?
Will it works on a 9550SX using 9.3.0.3 firmware ?
Could you update documentation about that somewhere, for exemple in 3w-9xxx.c header ?
Thanks very much.
Signature · 4 lines
/// Stephane Jourdois /"\ ASCII RIBBON CAMPAIGN \\\ ((( Consultant securite \ / AGAINST HTML MAIL ))) \\\ 24 rue Cauchy X /// \\\ 75015 Paris / \ +33 6 8643 3085 ///
Hi,
same problem over here. Why does the newest kernel contain an old version of the 3w-9xxx driver?
We are having performance problems using a 9550SX controller. Read throughput (measured with hdparm) is worse than on a Desktop system. We are considering trying to replace it with the newest driver from 3ware.com.
Greetz,
Martin
Quoted 22 lines · Stéphane Jourdois
Hi,
I have a question about 3w-9xxx driver versions :
3w-9xxx version in vanilla 2.6.16 is 2.26.02.005
3w-9xxx version in 2.6.17-rc1-mm2 is 2.26.02.006but :
3w-9xxx version in 3ware.com 9.3.0.3 codebase is 2.26.04.007The documentation with 9.3.0.3 codebase says it will not works with kernel driver <2.26.04.004. But I observe it works fine with codebase 9.3.0.2 (the documentation says it should not).
What is current status of 3w-9xxx driver in 2.6 ?
Will it works on a 9550SX using 9.3.0.3 firmware ?
Could you update documentation about that somewhere, for exemple in3w-9xxx.cheader ?Thanks very much.
Quoted 3 lines · Martin Honermeyer
We are having performance problems using a 9550SX controller. Read throughput (measured with hdparm) is worse than on a Desktop system. We are considering trying to replace it with the newest driver from 3ware.com.
I saw somewhere in the knowledgebase on there website that 2.26.02 is newer than 2.26.04.
anyway :
Don't test using hdparm, it doesn't works (I don't know why). Test using bonnie++. I have 100MB/s throughput reading and writing on a 9550SX-12. hdparm says 7MB/s.
Hope it helps.
Stéphane Jourdois.
Signature · 4 lines
/// Stephane Jourdois /"\ ASCII RIBBON CAMPAIGN \\\ ((( Consultant securite \ / AGAINST HTML MAIL ))) \\\ 24 rue Cauchy X /// \\\ 75015 Paris / \ +33 6 8643 3085 ///
In article <[email protected]>,
Quoted 8 lines · Martin Honermeyer
Hi,
same problem over here. Why does the newest kernel contain an old version of the 3w-9xxx driver?
We are having performance problems using a 9550SX controller. Read throughput (measured with hdparm) is worse than on a Desktop system. We are considering trying to replace it with the newest driver from 3ware.com.
The default settings for the 3w9xxx cards suck.
You need to make sure that the nr_requests (kernel request queue) is at least twice the size of queue_depth (hardware requests queue). Also the deadline or cfq i/o schedulers work a bit better for database-like workloads.
Try something like this, replacing sda with the device name of your 3ware controller.
# Limit queue depth somewhat
echo 128 > /sys/block/sda/device/queue_depth
# Increase nr_requests
echo 256 > /sys/block/sda/queue/nr_requests
# Don't use as for database-like loads echo deadline > /sys/block/sda/queue/scheduler
CFQ seems to like larger nr_requests, so if you use CFQ, try 254 (maximum hardware size) for queue_depth and 512 or 1024 for nr_requests.
Oh, remember, if you have just created a RAID array on the disks, wait with testing until the whole array has been rebuild..
Mike.