Skip to contentSkip to conversation

Add events for dm suspend / resume

PATCH In review Hannes Reinecke 2 participants 2 messages May 29, 2006 – Jun 1, 2006 Device mapper

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Add events for dm suspend / resume

Hi all,

currently device-mapper doesn't play well with udev & hotplug events. The event is sent out on the initial device create; only at this stage the device is not usable. Only after one did a 'table load' and a 'resume' the device is actually accessible from userland. And thus it is purely coincidental if any 'dmsetup' call from udev (which is triggered by the device create events) will return any useful data.

This patch adds two additional events 'online' and 'offline' which get send after 'resume' and 'suspend', respectively.
With this patch udev can hook on the 'online' event and will always get valid data via the dmsetup call.

Comments etc. are welcome.

Cheers,

Hannes

Signature · 4 lines
Dr. Hannes Reinecke			[email protected]
SuSE Linux Products GmbH		S390 & zSeries
Maxfeldstraße 5				+49 911 74053 688
90409 Nürnberg				http://www.suse.de
drivers/md/dm.c renamed from drivers/md/dm.c.orig +2 -0
@@ -1201,6 +1201,7 @@ int dm_suspend(struct mapped_device *md,
 	dm_table_postsuspend_targets(map);
 
 	set_bit(DMF_SUSPENDED, &md->flags);
+	kobject_uevent(&md->disk->kobj, KOBJ_OFFLINE);
 
 	r = 0;
 
@@ -1247,6 +1248,7 @@ int dm_resume(struct mapped_device *md)
 
 	dm_table_unplug_all(map);
 
+	kobject_uevent(&md->disk->kobj, KOBJ_ONLINE);
 	r = 0;
 
 out:
#1 lore raw
Quoted 1 line · Hannes Reinecke

currently device-mapper doesn't play well with udev & hotplug events.

That's a matter of opinion - I'd say it's udev that doesn't play well with device-mapper:-)

Quoted 11 lines

The event is sent out on the initial device create; only at this stage the device is not usable. Only after one did a 'table load' and a 'resume' the device is actually accessible from userland. And thus it is purely coincidental if any 'dmsetup' call from udev (which is triggered by the device create events) will return any useful data.
This patch adds two additional events 'online' and 'offline' which get send after 'resume' and 'suspend', respectively.

With this patch udev can hook on the 'online' event and will always get valid data via the dmsetup call.

'Always' is rather too strong: the device could already have changed again or even disappeared or mutated into a completely different device...

Very little seems to use kobject online/offline events yet, but this looks to me to be a reasonable use for them to reduce some of the existing problems.

So the new protocol would be:

add: Says nothing about whether or not it's ready to be used.
Ignore it. [Or create a /dev node if you want.]

online: The device is usable.
Trigger the multipath kpartx now, for example.

offline: I can't think of a need for this yet (and triggering udev events
when a device is suspended could cause problems) so I'd rather leave it out for now.

*But* before applying this, testing is needed to check the extra event can't lead to the machine locking up. For example, I notice some worrying allocations without mempools (or PF_MEMALLOC) in kobject_uevent(): 'suspend' and 'resume' are sections of device-mapper where such allocations are not permitted.

Assuming the memory allocation can be avoided or done safely, the change is a step in the right direction, but it still doesn't address the design problem with using an asynchronous udev for anything connected with device-mapper, namely that by the time the udev event gets around to being processed, the device's state could have changed - or it could even be a completely different device.

Alasdair.

Quoted 18 lines
drivers/md/dm.c renamed from drivers/md/dm.c.orig +2 -0
@@ -1201,6 +1201,7 @@ int dm_suspend(struct mapped_device *md,
 	dm_table_postsuspend_targets(map);
 
 	set_bit(DMF_SUSPENDED, &md->flags);
+	kobject_uevent(&md->disk->kobj, KOBJ_OFFLINE);
 
 	r = 0;
 
@@ -1247,6 +1248,7 @@ int dm_resume(struct mapped_device *md)
 
 	dm_table_unplug_all(map);
 
+	kobject_uevent(&md->disk->kobj, KOBJ_ONLINE);
 	r = 0;
 
 out: