Skip to contentSkip to conversation

newbie at routing !!

DISCUSSION Diana Asnani 3 participants 5 messages Jun 7, 2006 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Diana Asnani

author
#1 lore raw

Hi Vinod,

thanks for the reply...the gateway for my 192.168.202.1 PC is 192.168.202.14 which is the vlan router which enables me to ping the 192.168.206.1 vlan address...for the route in the network device control, the destination network is 192.168.206.0, the subnet mask 255.255.255.240 and the gateway as 192.168.202.14...this is what i have done so far...i am not too sure on how i should configure a default gateway ot static route...

Quoted 7 lines

From: Vinod Chandran <[email protected]>
To: Diana Asnani <[email protected]>
Subject: Re: newbie at routing !!
Date: Wed, 07 Jun 2006 14:17:47 +0530

Hi,

Quoted 18 lines

You need to have a route configured to reach 202.184.41.0/24 network. Check ur routing table
May be u need to configure a default gateway or a static route.

Regards,
Vinod C

Quoted 8 lines · Diana Asnani

Hi,

I need help!! My VLAN IP is 192.168.202.1. I can ping another PC with the VLAN IP of 192.168.206.1 but i can't ping the 202.184.41.41 address in that PC. Am i supposed to do some sort of routing configuration? I am using FC3 as my OS. What am i supposed to do to ping 202.184.41.41? Thanks

_________________________________________________________________
Get your mobile ringtones, operator logos and picture messages from MSN Mobile http://msn.smsfactory.no/

_________________________________________________________________
Find just what you are after with the more precise, more powerful new MSN Search. http://search.msn.com.my/ Try it now.

#2 lore raw

I am very tempted to just shout RTFM here. But then again, I'm already pissed at some other people, so let's just go back into friendly mode.... ;-)

If your PC has default route set to the VLAN router (192.168.202.14) that part is ok

The VLAN router will then need to know the route to 202.184.41.41/32 for the host itself or 202.14.41.0/24 if you need to reach the whole subnet, is via 192.168.206.1. I'm assuming both VLAN's are on the same VLAN router.

I don't know anything about your VLAN router, so I cannot tell you the command, but on cisco it will be:
ip route 208.184.41.41 255.255.255.255 192.168.206.1 (or for subnet ip route 208.184.41.0 255.255.255.0 192.168.206.1).

But if I must give you some real valuable advise, educate yourself. This is just part of the very basics of networking.

-Sietse
________________________________

From: [email protected] on behalf of Diana Asnani
Sent: Wed 07-Jun-06 12:46
To: [email protected]
Subject: Re: newbie at routing !!

Hi Vinod,

thanks for the reply...the gateway for my 192.168.202.1 PC is 192.168.202.14 which is the vlan router which enables me to ping the 192.168.206.1 vlan address...for the route in the network device control, the destination network is 192.168.206.0, the subnet mask 255.255.255.240 and the gateway as 192.168.202.14...this is what i have done so far...i am not too sure on how i should configure a default gateway ot static route...

Quoted 7 lines

From: Vinod Chandran <[email protected]>
To: Diana Asnani <[email protected]>
Subject: Re: newbie at routing !!
Date: Wed, 07 Jun 2006 14:17:47 +0530

Hi,

Quoted 22 lines

You need to have a route configured to reach 202.184.41.0/24 network. Check ur routing table
May be u need to configure a default gateway or a static route.

Regards,
Vinod C

Quoted 12 lines · Diana Asnani

Hi,

I need help!! My VLAN IP is 192.168.202.1. I can ping another PC with the VLAN IP of 192.168.206.1 but i can't ping the 202.184.41.41 address in that PC. Am i supposed to do some sort of routing configuration? I am using FC3 as my OS. What am i supposed to do to ping 202.184.41.41? Thanks

_________________________________________________________________
Get your mobile ringtones, operator logos and picture messages from MSN Mobile http://msn.smsfactory.no/

_________________________________________________________________
Find just what you are after with the more precise, more powerful new MSN Search. http://search.msn.com.my/ Try it now.

author
#3 lore raw

RTFM?
no, the VLANs are not connected to the same router...the vlan router for 192.168.206.1 is 192.168.206.14 the router is Cisco...
yes, i will take your valuable advice...

Quoted 68 lines

From: "Sietse van Zanen" <[email protected]>
To: "Diana Asnani" <[email protected]>, <[email protected]>
Subject: RE: newbie at routing !!
Date: Wed, 7 Jun 2006 13:17:14 +0200

I am very tempted to just shout RTFM here. But then again, I'm already pissed at some other people, so let's just go back into friendly mode.... ;-)

If your PC has default route set to the VLAN router (192.168.202.14) that part is ok

The VLAN router will then need to know the route to 202.184.41.41/32 for the host itself or 202.14.41.0/24 if you need to reach the whole subnet, is via 192.168.206.1. I'm assuming both VLAN's are on the same VLAN router.

I don't know anything about your VLAN router, so I cannot tell you the command, but on cisco it will be:
ip route 208.184.41.41 255.255.255.255 192.168.206.1 (or for subnet ip route 208.184.41.0 255.255.255.0 192.168.206.1).

But if I must give you some real valuable advise, educate yourself. This is just part of the very basics of networking.

-Sietse
________________________________

From: [email protected] on behalf of Diana Asnani
Sent: Wed 07-Jun-06 12:46
To: [email protected]
Subject: Re: newbie at routing !!

Hi Vinod,

thanks for the reply...the gateway for my 192.168.202.1 PC is 192.168.202.14 which is the vlan router which enables me to ping the 192.168.206.1 vlan address...for the route in the network device control, the destination network is 192.168.206.0, the subnet mask 255.255.255.240 and the gateway as 192.168.202.14...this is what i have done so far...i am not too sure on how i should configure a default gateway ot static route...

Quoted 7 lines

From: Vinod Chandran <[email protected]>
To: Diana Asnani <[email protected]>
Subject: Re: newbie at routing !!
Date: Wed, 07 Jun 2006 14:17:47 +0530

Hi,

Quoted 12 lines

You need to have a route configured to reach 202.184.41.0/24 network. Check ur routing table
May be u need to configure a default gateway or a static route.

Regards,
Vinod C

Quoted 3 lines · Diana Asnani

Hi,

I need help!! My VLAN IP is 192.168.202.1. I can ping another PC with

the

Quoted 3 lines
Quoted 3 lines

VLAN IP of 192.168.206.1 but i can't ping the 202.184.41.41 address in that PC. Am i supposed to do some sort of routing configuration? I am using FC3 as my OS. What am i supposed to do to ping 202.184.41.41?

Thanks

Quoted 7 lines
Quoted 6 lines

_________________________________________________________________
Get your mobile ringtones, operator logos and picture messages from MSN Mobile http://msn.smsfactory.no/

Quoted 7 lines

_________________________________________________________________
Find just what you are after with the more precise, more powerful new MSN Search. http://search.msn.com.my/ Try it now.

_________________________________________________________________
Block pop-up ads with MSN Toolbar. http://toolbar.msn.com.my/

#4 lore raw

On Wed, 07 Jun 2006 20:24:44 +0800, Diana wrote in message <[email protected]>:

Quoted 1 line

RTFM?

..an ooooold classic: http://www.catb.org/jargon/html/R/RTFM.html
Variants include fine, feeble, funny. ;o)

Signature · 4 lines
..med vennlig hilsen = with Kind Regards from Arnt... ;o)
...with a number of polar bear hunters in his ancestry...
  Scenarios always come in sets of three: 
  best case, worst case, and just in case.
#5 lore raw
In reply to Diana Asnani

Well if there are more routers in between, the short answer becomes:

All routers in between the two end points need to know the routes to both end points.

-Sietse

________________________________

From: [email protected] on behalf of Diana Asnani
Sent: Wed 07-Jun-06 14:24
To: [email protected]
Subject: RE: newbie at routing !!

RTFM?
no, the VLANs are not connected to the same router...the vlan router for 192.168.206.1 is 192.168.206.14
the router is Cisco...
yes, i will take your valuable advice...

Quoted 79 lines

From: "Sietse van Zanen" <[email protected]>
To: "Diana Asnani" <[email protected]>,
<[email protected]>
Subject: RE: newbie at routing !!
Date: Wed, 7 Jun 2006 13:17:14 +0200

I am very tempted to just shout RTFM here. But then again, I'm already pissed at some other people, so let's just go back into friendly mode.... ;-)

If your PC has default route set to the VLAN router (192.168.202.14) that part is ok

The VLAN router will then need to know the route to 202.184.41.41/32 for the host itself or 202.14.41.0/24 if you need to reach the whole subnet, is via 192.168.206.1. I'm assuming both VLAN's are on the same VLAN router.

I don't know anything about your VLAN router, so I cannot tell you the command, but on cisco it will be:
ip route 208.184.41.41 255.255.255.255 192.168.206.1 (or for subnet ip route 208.184.41.0 255.255.255.0 192.168.206.1).

But if I must give you some real valuable advise, educate yourself. This is just part of the very basics of networking.

-Sietse
________________________________

From: [email protected] on behalf of Diana Asnani
Sent: Wed 07-Jun-06 12:46
To: [email protected]
Subject: Re: newbie at routing !!

Hi Vinod,

thanks for the reply...the gateway for my 192.168.202.1 PC is 192.168.202.14
which is the vlan router which enables me to ping the 192.168.206.1 vlan address...for the route in the network device control, the destination network is 192.168.206.0, the subnet mask 255.255.255.240 and the gateway as
192.168.202.14...this is what i have done so far...i am not too sure on how i should configure a default gateway ot static route...

Quoted 7 lines

From: Vinod Chandran <[email protected]>
To: Diana Asnani <[email protected]>
Subject: Re: newbie at routing !!
Date: Wed, 07 Jun 2006 14:17:47 +0530

Hi,

Quoted 12 lines

You need to have a route configured to reach 202.184.41.0/24 network. Check ur routing table
May be u need to configure a default gateway or a static route.

Regards,
Vinod C

Quoted 3 lines · Diana Asnani

Hi,

I need help!! My VLAN IP is 192.168.202.1. I can ping another PC with

the

Quoted 3 lines
Quoted 3 lines

VLAN IP of 192.168.206.1 but i can't ping the 202.184.41.41 address in that PC. Am i supposed to do some sort of routing configuration? I am using FC3 as my OS. What am i supposed to do to ping 202.184.41.41?

Thanks

Quoted 7 lines
Quoted 6 lines

_________________________________________________________________
Get your mobile ringtones, operator logos and picture messages from MSN Mobile http://msn.smsfactory.no/

Quoted 7 lines

_________________________________________________________________
Find just what you are after with the more precise, more powerful new MSN Search. http://search.msn.com.my/ Try it now.

_________________________________________________________________
Block pop-up ads with MSN Toolbar. http://toolbar.msn.com.my/