2.6.17-rc5-mm3 - USB issues
All,
My USB hub isn't recognised with the latest -mm series, whereas with 2.6.16 vanilla it is picked up & used immediately.
The error I get in dmesg is;
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-4: new high speed USB device using ehci_hcd and address 3ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ. usb 1-4: device not accepting address 3, error -110
usb 1-4: new high speed USB device using ehci_hcd and address 4
usb 1-4: device not accepting address 4, error -110
usb 1-4: new high speed USB device using ehci_hcd and address 5
usb 1-4: device not accepting address 5, error -110
usb 1-4: new high speed USB device using ehci_hcd and address 6
usb 1-4: device not accepting address 6, error -110
usb 2-2: new full speed USB device using uhci_hcd and address 2
Which seems to be related to my Belkin hub. The full USB related dmesg information can be found below, I'm happy to provide further debugging information as required :)
ACPI (acpi_bus-0192): Device `USB9]is not power manageable [20060310]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 ehci_hcd 0000:00:10.3: EHCI Host Controllerehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.3: irq 10, io mem 0xea022000ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc5-mm3 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI (acpi_bus-0192): Device `USB6]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:10.0: UHCI Host Controlleruhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc5-mm3 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI (acpi_bus-0192): Device `USB7]is not power manageable [20060310]
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:10.1: UHCI Host Controlleruhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 11, io base 0x0000d400
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc5-mm3 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI (acpi_bus-0192): Device `USB8]is not power manageable [20060310]
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:10.2: UHCI Host Controlleruhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d800
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.17-rc5-mm3 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-4: new high speed USB device using ehci_hcd and address 3ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ. usb 1-4: device not accepting address 3, error -110
usb 1-4: new high speed USB device using ehci_hcd and address 4
usb 1-4: device not accepting address 4, error -110
usb 1-4: new high speed USB device using ehci_hcd and address 5
usb 1-4: device not accepting address 5, error -110
usb 1-4: new high speed USB device using ehci_hcd and address 6
usb 1-4: device not accepting address 6, error -110
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 2-2: new device found, idVendor=0731, idProduct=0528
usb 2-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new driver usblpdrivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhiddrivers/usb/input/hid-core.c: v2.6:USB HID core driver
Further to this, I tested with 2.6.17-rc6-mm2 today, no changes. I've attached as .txt files the following;
lsusb output for both a 2.6.16 kernel and the 2.6.17-rc6-mm2 kernel /proc/bus/usb/devices output, again for the same kernels.
Noting that there are a lot less devices in the -mm kernel due to the error below.
Again, any further debugging I can provide, just let me know!
:)J
Please advise
Quoted 91 lines · Johny Ågotnes
All,
My USB hub isn't recognised with the latest -mm series, whereas with 2.6.16 vanilla it is picked up & used immediately.
The error I get in dmesg is;
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-4: new high speed USB device usingehci_hcdand address 3ehci_hcd0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ. usb 1-4: device not accepting address 3, error -110
usb 1-4: new high speed USB device usingehci_hcdand address 4
usb 1-4: device not accepting address 4, error -110
usb 1-4: new high speed USB device usingehci_hcdand address 5
usb 1-4: device not accepting address 5, error -110
usb 1-4: new high speed USB device usingehci_hcdand address 6
usb 1-4: device not accepting address 6, error -110
usb 2-2: new full speed USB device usinguhci_hcdand address 2Which seems to be related to my Belkin hub. The full USB related dmesg information can be found below, I'm happy to provide further debugging information as required :)
ACPI (acpi_bus-0192): Device `USB9]is not power manageable [20060310]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10ehci_hcd0000:00:10.3: EHCI Host Controllerehci_hcd0000:00:10.3: new USB bus registered, assigned bus number 1ehci_hcd0000:00:10.3: irq 10, io mem0xea022000ehci_hcd0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc5-mm3ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI (acpi_bus-0192): Device `USB6]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11uhci_hcd0000:00:10.0: UHCI Host Controlleruhci_hcd0000:00:10.0: new USB bus registered, assigned bus number 2uhci_hcd0000:00:10.0: irq 11, io base0x0000d000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc5-mm3uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI (acpi_bus-0192): Device `USB7]is not power manageable [20060310]
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11uhci_hcd0000:00:10.1: UHCI Host Controlleruhci_hcd0000:00:10.1: new USB bus registered, assigned bus number 3uhci_hcd0000:00:10.1: irq 11, io base0x0000d400
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc5-mm3uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI (acpi_bus-0192): Device `USB8]is not power manageable [20060310]
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10uhci_hcd0000:00:10.2: UHCI Host Controlleruhci_hcd0000:00:10.2: new USB bus registered, assigned bus number 4uhci_hcd0000:00:10.2: irq 10, io base0x0000d800
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.17-rc5-mm3uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-4: new high speed USB device usingehci_hcdand address 3ehci_hcd0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ. usb 1-4: device not accepting address 3, error -110
usb 1-4: new high speed USB device usingehci_hcdand address 4
usb 1-4: device not accepting address 4, error -110
usb 1-4: new high speed USB device usingehci_hcdand address 5
usb 1-4: device not accepting address 5, error -110
usb 1-4: new high speed USB device usingehci_hcdand address 6
usb 1-4: device not accepting address 6, error -110
usb 2-2: new full speed USB device usinguhci_hcdand address 2
usb 2-2: new device found, idVendor=0731, idProduct=0528
usb 2-2: new device strings: Mfr=0, Product=0, SerialNumber=0
Quoted 9 lines
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new driver usblpdrivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhiddrivers/usb/input/hid-core.c: v2.6:USB HID core driver
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.16-gentoo-r7 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:10.2 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.16-gentoo-r7 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:10.1 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.16-gentoo-r7 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:10.0 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0731 ProdID=0528 Rev= 0.01 C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 10 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.16-gentoo-r7 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:10.3 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=6017 ProdID=2230 Rev=c5.bd S: Manufacturer=Sunplus Technology Inc. S: Product=USB to Serial-ATA bridge S: SerialNumber=External D000FFFF_00000000_0_A C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 4 Spd=480 MxCh= 7 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1 P: Vendor=050d ProdID=0237 Rev= 0.00 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms I: If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=04 Port=01 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=05a9 ProdID=4519 Rev= 1.00 S: Manufacturer=OmniVision Technologies, Inc. S: Product=USB Camera C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=01(Isoc) MxPS= 384 Ivl=1ms I: If#= 0 Alt= 2 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=01(Isoc) MxPS= 512 Ivl=1ms I: If#= 0 Alt= 3 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=01(Isoc) MxPS= 768 Ivl=1ms I: If#= 0 Alt= 4 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=01(Isoc) MxPS= 896 Ivl=1ms I: If#= 1 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=00 Driver=(none) I: If#= 2 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none) I: If#= 2 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none) E: Ad=82(I) Atr=05(Isoc) MxPS= 40 Ivl=1ms
T: Bus=01 Lev=02 Prnt=04 Port=02 Cnt=02 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=13b1 ProdID=001d Rev= 1.40 S: Manufacturer=LINKSYS S: Product=Linksys CIT200 S: SerialNumber=USBGAP00000000000000000000166124961 C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=00 Driver=(none) I: If#= 1 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none) I: If#= 1 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none) E: Ad=02(O) Atr=05(Isoc) MxPS= 64 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none) I: If#= 2 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none) E: Ad=81(I) Atr=05(Isoc) MxPS= 64 Ivl=1ms I: If#= 3 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=255ms
T: Bus=01 Lev=02 Prnt=04 Port=05 Cnt=03 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev= 2.72 C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none) T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.17-rc6-mm2 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:10.2 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.17-rc6-mm2 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:10.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.17-rc6-mm2 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:10.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0731 ProdID=0528 Rev= 0.01 C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 10 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.17-rc6-mm2 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:10.3 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0731:0528 Susteen, Inc. SonyEricsson DCU-11 Cable Bus 002 Device 001: ID 0000:0000
Bus 001 Device 007: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 001 Device 006: ID 13b1:001d Linksys
Bus 001 Device 005: ID 05a9:4519 OmniVision Technologies, Inc.
Bus 001 Device 004: ID 050d:0237 Belkin Components
Bus 001 Device 003: ID 6017:2230
Bus 001 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0731:0528 Susteen, Inc. SonyEricsson DCU-11 Cable Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000