Skip to contentSkip to conversation

Can't use USB devices in their designated applications on Windows Vista guest

DISCUSSION Dirk Heinrichs 3 participants 5 messages Sep 18, 2012 – Sep 20, 2012 KVM

lore
Share & tools
lore
#0 lore raw

Hi,

I have a really strange problem using USB devices in a Windows Vista (32bit) guest. After adding a USB device (an Adroid phone or a GPS navigation device) to the guest, Vista starts to install the driver(s) for the new device just as it would do on real hardware.

However, when it comes to actually use that device in the Windows application that came with it (for example Samsung Kies in case of the Android phone), those applications do not recognize the device and keep waiting for the device to be connected forever.

Any idea how I could solve this problem?

Thanks...

Dirk

Signature · 3 lines
Dirk Heinrichs <[email protected]>
Tel: +49 (0)2471 209385 | Mobil: +49 (0)176 34473913
GPG Public Key C2E467BB | Jabber: [email protected]
#1 lore raw

Could be that windows is seeing a USB 1 device while needing a USB 2.
You might solve this by passing through the devices explicitly; go to the Qemu console, and type USB-INFO(if I remember rightly) while the device is plugged in.
This will show you all connected devices, including vendor id etc.
Then add that device no and vendor ID to your qemu command line(in the right way, look at documentation/google) and pass it through explicitly, OR it may be solved by using ehci control to pass USB 2. I know we had a similar problem about 6 months ago.
Ehci support in kvm-qemu should show up in google.

----------------------------------------

Quoted 26 lines

From: [email protected]
To: [email protected]
Subject: Can't use USB devices in their designated applications on Windows Vista guest
Date: Tue, 18 Sep 2012 07:56:48 +0200

Hi,

I have a really strange problem using USB devices in a Windows Vista (32bit) guest. After adding a USB device (an Adroid phone or a GPS navigation device) to the guest, Vista starts to install the driver(s) for the new device just as it would do on real hardware.

However, when it comes to actually use that device in the Windows application that came with it (for example Samsung Kies in case of the Android phone), those applications do not recognize the device and keep waiting for the device to be connected forever.

Any idea how I could solve this problem?

Thanks...

Dirk
--
Dirk Heinrichs <[email protected]>
Tel: +49 (0)2471 209385 | Mobil: +49 (0)176 34473913 GPG Public Key C2E467BB | Jabber: [email protected]

#2 lore raw

Am Dienstag 18 September 2012, 06:42:18 schrieb Veruca Salt:

Quoted 9 lines

Could be that windows is seeing a USB 1 device while needing a USB 2. You might solve this by passing through the devices explicitly; go to the Qemu console, and type USB-INFO(if I remember rightly) while the device is plugged in. This will show you all connected devices, including vendor id etc. Then add that device no and vendor ID to your qemu command line(in the right way, look at documentation/google) and pass it through explicitly, OR it may be solved by using ehci control to pass USB 2. I know we had a similar problem about 6 months ago.
Ehci support in kvm-qemu should show up in google.

Thank you very much. I wasn't aware that KVM only adds a USB 1.x controller. However, I have now been able to add an USB 2 controller, but the behaviour is still same. Drivers are installed, applications do not recognize the devices.

Bye...

Dirk

Signature · 3 lines
Dirk Heinrichs <[email protected]>
Tel: +49 (0)2471 209385 | Mobil: +49 (0)176 34473913
GPG Public Key C2E467BB | Jabber: [email protected]
#3 lore raw
In reply to Dirk Heinrichs
Quoted 11 lines · Dirk Heinrichs

Hi,

I have a really strange problem using USB devices in a Windows Vista (32bit) guest. After adding a USB device (an Adroid phone or a GPS navigation device) to the guest, Vista starts to install the driver(s) for the new device just as it would do on real hardware.

However, when it comes to actually use that device in the Windows application that came with it (for example Samsung Kies in case of the Android phone), those applications do not recognize the device and keep waiting for the device to be connected forever.

This appears to be the same as https://bugs.launchpad.net/bugs/1033727 , FWIW.

/mjt