Skip to contentSkip to conversation

u-boot crashing while searching PCI device

U-Boot-Users robinpv 2 participants 5 messages Jul 11, 2006 – Jul 13, 2006

lore
Share & tools
lore

robinpv

author
#0 lore raw

Hi,
I have a MPC5200 based board, with PCI 2250 PCI-PCI bridge and 2 RTL8110S ethernet controller on the PCI Bridge. I have set the CONFIG_PCI_PNP option.
Bus Dev VID DID

00    12     104C AC23   Bridge
01    02     10EC   8169   Ethernet Chip
01    03     10EC   8169   Ethernet Chip

u-boot is able to detect the Bridge controller. But when it searching for the ethernet devices
before the device and function number for the ethernet chip is reached the u-boot is crashing.
It is crashing when it trying to read the header type [ pci_hose_scan_bus() in pci.c ]
of the device which is not present. Instead of getting data as 0xFF, u-boot is crashing.

I tried the same in linux, The bridge and the ethernet device is detected and mem,mmio and io
regions are allocated for the ethernet. But when i try to access ethernet registers, all the values
are 0xFF.
I checked the values of the PCI Bridge registers in u-boot and linux. All the registers are same
but the memory and io base , limit are differnet. I guess that should not the problem.
Can some point out why the u-boot is crashing when searching device??

Thanks in advance,
Robin

#1 lore raw
Quoted 5 lines · In message <[email protected]> you wrote:

u-boot is able to detect the Bridge controller. But when it searching for the ethernet devices
before the device and function number for the ethernet chip is reached the u-boot is crashing.

Which exact version of U-Boot (git commit ID?) is this?

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Without facts, the decision cannot be made logically. You  must  rely
on your human intuition.
	-- Spock, "Assignment: Earth", stardate unknown
author
#2 lore raw

I am using the u-boot 1.1.4 from the below link.
http://prdownloads.sourceforge.net/u-boot/u-boot-1.1.4.tar.bz2
I don't have the commit ID .

Regards
Robin

Quoted 18 lines · Wolfgang Denk
Quoted 6 lines · In message <[email protected]> you wrote:

u-boot is able to detect the Bridge controller. But when it searching for the ethernet devices
before the device and function number for the ethernet chip is reached the u-boot is crashing.

Which exact version of U-Boot (git commit ID?) is this?

Best regards,

Wolfgang Denk

#3 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

I am using the u-boot 1.1.4 from the below link.
http://prdownloads.sourceforge.net/u-boot/u-boot-1.1.4.tar.bz2

Try using the current version (top of tree in git) instead.

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If I don't document something, it's usually either for a good reason,
or a bad reason.  In this case it's a good reason.  :-)
                 - Larry Wall in <[email protected]>
author
#4 lore raw
In reply to robinpv

I tried the latest version of the U-Boot 1.1.4-dirty downloaded couple of days back,
In this version any of the devices on the bus 0 is not detected. In the u-boot 1.1.4 version that i was using earlier i am able to detect the devices and the pci bridge.

Regards,
Robin

Quoted 29 lines · robinpv

I am using the u-boot 1.1.4 from the below link.
http://prdownloads.sourceforge.net/u-boot/u-boot-1.1.4.tar.bz2
I don't have the commit ID .

Regards
Robin

Quoted 18 lines · Wolfgang Denk
Quoted 5 lines · In message <[email protected]> you wrote:

u-boot is able to detect the Bridge controller. But when it searching for the ethernet devices
before the device and function number for the ethernet chip is reached the u-boot is crashing.

Which exact version of U-Boot (git commit ID?) is this?

Best regards,

Wolfgang Denk