Skip to contentSkip to conversation

Try 2: Add wireless statistics to d80211

PATCH In review Larry Finger 3 participants 6 messages Aug 24, 2006

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/4 Try 2: Add wireless statistics to d80211

This patch modifies d80211 to add wireless statistics.

======================================

include/net/d80211.h +5 -0
index 42fdbf7..70655dc 100644
@@ -205,6 +205,8 @@ struct ieee80211_rx_status {
         int channel;
         int phymode;
         int ssi;
+	int signal;
+	int noise;
         int antenna;
         int rate;
         int flag;
@@ -499,6 +501,9 @@ struct ieee80211_hw {
         /* This is the time in us to change channels
          */
         int channel_change_time;
+	/* This is maximum value of rssi reported by this interface
+	 */
+	int maxssi;
 
 	int num_modes;
 	struct ieee80211_hw_modes *modes;
net/d80211/ieee80211.c +2 -0
index e72721f..2549484 100644
@@ -3175,6 +3175,8 @@ ieee80211_rx_h_sta_process(struct ieee80
 	sta->rx_fragments++;
 	sta->rx_bytes += rx->skb->len;
 	sta->last_rssi = rx->u.rx.status->ssi;
+	sta->last_signal = rx->u.rx.status->signal;
+	sta->last_noise = rx->u.rx.status->noise;
 
 	if (!(rx->fc & IEEE80211_FCTL_MOREFRAGS)) {
 		/* Change STA power saving mode only in the end of a frame
net/d80211/ieee80211_i.h +1 -0
index 0d2d79d..1271513 100644
@@ -336,6 +336,7 @@ struct ieee80211_local {
 	struct net_device *apdev; /* wlan#ap - management frames (hostapd) */
 	int open_count;
 	int monitors;
+	struct iw_statistics wstats;
 	struct ieee80211_conf conf;
 
 	int dev_index;
net/d80211/ieee80211_ioctl.c +44 -1

69 lines not on this page · raw message

net/d80211/ieee80211_sysfs_sta.c +4 -0
index 94c6dd8..dd92b02 100644
@@ -72,6 +72,8 @@ STA_ATTR(last_txrate, last_txrate, RATE)
 STA_ATTR(tx_retry_failed, tx_retry_failed, LU);
 STA_ATTR(tx_retry_count, tx_retry_count, LU);
 STA_ATTR(last_rssi, last_rssi, D);
+STA_ATTR(last_signal, last_signal, D);
+STA_ATTR(last_noise, last_noise, D);
 STA_ATTR(channel_use, channel_use, D);
 STA_ATTR(wep_weak_iv_count, wep_weak_iv_count, D);
@@ -175,6 +177,8 @@ static struct attribute *sta_ktype_attrs
 	&sta_attr_tx_retry_failed.attr,
 	&sta_attr_tx_retry_count.attr,
 	&sta_attr_last_rssi.attr,
+	&sta_attr_last_signal.attr,
+	&sta_attr_last_noise.attr,
 	&sta_attr_channel_use.attr,
 	&sta_attr_wep_weak_iv_count.attr,
 
net/d80211/sta_info.h +2 -0
index 8d23047..100d039 100644
@@ -82,6 +82,8 @@ struct sta_info {
 	unsigned long rx_dropped; /* number of dropped MPDUs from this STA */
 
 	int last_rssi; /* RSSI of last received frame from this STA */
+	int last_signal; /* signal of last received frame from this STA */
+	int last_noise; /* noise of last received frame from this STA */
 	int last_ack_rssi[3]; /* RSSI of last received ACKs from this STA */
 	unsigned long last_ack;
         int channel_use;
#1 lore raw
Quoted 3 lines · Larry Finger

This patch modifies d80211 to add wireless statistics.

Please fix the Signed-off-by line.

Quoted 16 lines

======================================

include/net/d80211.h +2 -0
index 42fdbf7..70655dc 100644
@@ -205,6 +205,8 @@ struct ieee80211_rx_status {
          int channel;
          int phymode;
          int ssi;
+	int signal;
+	int noise;
          int antenna;
          int rate;
          int flag;

include/net/d80211.h struct ieee80211_hw { · line 506

Quoted 6 lines
include/net/d80211.h +3 -0
@@ -499,6 +501,9 @@ struct ieee80211_hw {
          /* This is the time in us to change channels
           */
          int channel_change_time;
+	/* This is maximum value of rssi reported by this interface
+	 */
+	int maxssi;

Device, not interface. And please do not put */ to a new line.

net/d80211/ieee80211_ioctl.c static int ieee80211_ioctl_giwauth(struc · line 3067

Quoted 12 lines

[...]

net/d80211/ieee80211_ioctl.c +0 -1
[...]
@@ -3019,7 +3062,6 @@ static int ieee80211_ioctl_giwauth(struc
  	return ret;
  }
 
-
  static int ieee80211_ioctl_siwencodeext(struct net_device *dev,
  					struct iw_request_info *info,
  					struct iw_point *erq, char *extra)

Please do not touch parts outside of the code you are fixing/improving/etc. We'll need a code style patch later, but not now - there are still too many patches floating around and I don't want to break them more than is necessary.

Other then that, it looks good.

Thanks,

Jiri

Signature · 2 lines
Jiri Benc
SUSE Labs
#2 lore raw
Quoted 7 lines · Jiri Benc

include/net/d80211.h struct ieee80211_hw { · line 506

Quoted 4 lines · Larry Finger

This patch modifies d80211 to add wireless statistics.

include/net/d80211.h +3 -0
+	/* This is maximum value of rssi reported by this interface
+	 */
+	int maxssi;

Device, not interface. And please do not put */ to a new line.

Noted on the first part, but I would like a clarification regarding style. I put the */ on the second line to match the rest of that section. Should a patch try to keep the local style in that part of the code, or change it to a some other standard?

Larry

#3 lore raw
Quoted 3 lines · Larry Finger

Noted on the first part, but I would like a clarification regarding style. I put the */ on the second line to match the rest of that section. Should a patch try to keep the local style in that part of the code, or change it to a some other standard?

Patches should convert the code they are touching to coding style common in the kernel. This way we will gradually convert at least part of d80211 to the kernel coding style; the rest will be addressed by one big patch just before merging into the vanilla (or -mm).

Thanks,

Jiri

Signature · 2 lines
Jiri Benc
SUSE Labs
#4 lore raw
In reply to Larry Finger

Why have both signal and rssi measures?

Simon

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Larry Finger
Sent: Wednesday, August 23, 2006 8:02 PM
To: Jiri Benc
Cc: John Linville; [email protected]
Subject: [PATCH 1/4] Try 2: Add wireless statistics to d80211

This patch modifies d80211 to add wireless statistics.

======================================

include/net/d80211.h index renamed from include/net/d80211.h +0 -0

42fdbf7..70655dc 100644

include/net/d80211.h +5 -0
@@ -205,6 +205,8 @@ struct ieee80211_rx_status {
          int channel;
          int phymode;
          int ssi;
+	int signal;
+	int noise;
          int antenna;
          int rate;
          int flag;
@@ -499,6 +501,9 @@ struct ieee80211_hw {
          /* This is the time in us to change channels
           */
          int channel_change_time;
+	/* This is maximum value of rssi reported by this interface
+	 */
+	int maxssi;
 
  	int num_modes;
  	struct ieee80211_hw_modes *modes;
net/d80211/ieee80211.c index renamed from net/d80211/ieee80211.c +0 -0

e72721f..2549484 100644

net/d80211/ieee80211.c +2 -0
@@ -3175,6 +3175,8 @@ ieee80211_rx_h_sta_process(struct ieee80
  	sta->rx_fragments++;
  	sta->rx_bytes += rx->skb->len;
  	sta->last_rssi = rx->u.rx.status->ssi;
+	sta->last_signal = rx->u.rx.status->signal;
+	sta->last_noise = rx->u.rx.status->noise;
 
  	if (!(rx->fc & IEEE80211_FCTL_MOREFRAGS)) {
  		/* Change STA power saving mode only in the end of a

frame diff --git a/net/d80211/ieee80211_i.h b/net/d80211/ieee80211_i.h index 0d2d79d..1271513 100644

net/d80211/ieee80211_i.h +0 -0
@@ -336,6 +336,7 @@ struct ieee80211_local {
  	struct net_device *apdev; /* wlan#ap - management frames

(hostapd) */
int open_count;
int monitors;
+ struct iw_statistics wstats;
struct ieee80211_conf conf;

int dev_index;

net/d80211/ieee80211_ioctl.c +2 -0
index 89a58e3..b121302 100644
@@ -1581,6 +1581,16 @@ static int ieee80211_ioctl_giwrange(stru
  	range->min_frag = 256;
  	range->max_frag = 2346;
 
+	range->max_qual.qual = 100;
+	range->max_qual.level = 146;  /* set floor at -110 dBm (146 -

256) */
+ range->max_qual.noise = 146;
+ range->max_qual.updated = IW_QUAL_ALL_UPDATED;
+
+ range->avg_qual.qual = 50;
+ range->avg_qual.level = 0;
+ range->avg_qual.noise = 0;
+ range->avg_qual.updated = IW_QUAL_ALL_UPDATED;
+
return 0;
}

@@ -2996,6 +3006,39 @@ static int ieee80211_ioctl_siwauth(struc
return ret;
}

+/* Get wireless statistics. Called by /proc/net/wireless and by +SIOCGIWSTATS */ static struct iw_statistics +*ieee80211_get_wireless_stats(struct net_device *net_dev) {
+ struct ieee80211_local *local = net_dev->ieee80211_ptr;
+ struct iw_statistics * wstats = &local->wstats;
+ struct ieee80211_sub_if_data *sdata =
IEEE80211_DEV_TO_SUB_IF(net_dev);
+ struct sta_info *sta;
+ static int tmp_level = 0;
+ static int tmp_qual = 0;
+
+ sta = sta_info_get(local, sdata->u.sta.bssid);
+ if (!sta) {
+ wstats->discard.fragment = 0;
+ wstats->discard.misc = 0;
+ wstats->qual.qual = 0;
+ wstats->qual.level = 0;
+ wstats->qual.noise = 0;
+ wstats->qual.updated = IW_QUAL_ALL_INVALID;
+ } else {
+ if (!tmp_level) { /* get initial values */
+ tmp_level = sta->last_signal;
+ tmp_qual = sta->last_rssi;
+ } else { /* smooth results */
+ tmp_level = (15 * tmp_level +
sta->last_signal)/16;
+ tmp_qual = (15 * tmp_qual + sta->last_rssi)/16;
+ }
+ wstats->qual.level = tmp_level;
+ wstats->qual.qual = 100*tmp_qual/local->hw->maxssi;
+ wstats->qual.noise = sta->last_noise;
+ wstats->qual.updated = IW_QUAL_ALL_UPDATED |
IW_QUAL_DBM;
+ }
+ return wstats;
+}

static int ieee80211_ioctl_giwauth(struct net_device *dev,
struct iw_request_info *info,
@@ -3019,7 +3062,6 @@ static int ieee80211_ioctl_giwauth(struc
return ret;
}

-
static int ieee80211_ioctl_siwencodeext(struct net_device *dev,
struct iw_request_info *info, struct iw_point *erq, char
*extra) @@ -3184,6 +3226,7 @@ const struct iw_handler_def ieee80211_iw
.standard = (iw_handler *) ieee80211_handler,
.private = (iw_handler *) ieee80211_private_handler,
.private_args = (struct iw_priv_args *) ieee80211_ioctl_priv,
+ .get_wireless_stats = ieee80211_get_wireless_stats,
};

/* Wireless handlers for master interface */ diff --git
a/net/d80211/ieee80211_sysfs_sta.c b/net/d80211/ieee80211_sysfs_sta.c index 94c6dd8..dd92b02 100644

net/d80211/ieee80211_sysfs_sta.c +2 -0
@@ -72,6 +72,8 @@ STA_ATTR(last_txrate, last_txrate, RATE)
  STA_ATTR(tx_retry_failed, tx_retry_failed, LU);
  STA_ATTR(tx_retry_count, tx_retry_count, LU);
  STA_ATTR(last_rssi, last_rssi, D);
+STA_ATTR(last_signal, last_signal, D);
+STA_ATTR(last_noise, last_noise, D);
  STA_ATTR(channel_use, channel_use, D);
  STA_ATTR(wep_weak_iv_count, wep_weak_iv_count, D); @@ -175,6 +177,8 @@

static struct attribute *sta_ktype_attrs
&sta_attr_tx_retry_failed.attr,
&sta_attr_tx_retry_count.attr,
&sta_attr_last_rssi.attr,
+ &sta_attr_last_signal.attr,
+ &sta_attr_last_noise.attr,
&sta_attr_channel_use.attr,
&sta_attr_wep_weak_iv_count.attr,

net/d80211/sta_info.h index renamed from net/d80211/sta_info.h +0 -0

8d23047..100d039 100644

net/d80211/sta_info.h +0 -0
@@ -82,6 +82,8 @@ struct sta_info {
  	unsigned long rx_dropped; /* number of dropped MPDUs from this

STA */

int last_rssi; /* RSSI of last received frame from this STA */
+ int last_signal; /* signal of last received frame from this STA
*/
+ int last_noise; /* noise of last received frame from this STA */
int last_ack_rssi[3]; /* RSSI of last received ACKs from this
STA */

  	unsigned long last_ack;
          int channel_use;

-
To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to [email protected] More majordomo info at
http://vger.kernel.org/majordomo-info.html

#5 lore raw
Quoted 1 line · Simon Barber

Why have both signal and rssi measures?

In the bcm43xx driver, the values are different. There is a routine that converts from rssi as a positive number into signal in a negative number that looks like dBm. Because of the reverse engineering, we have no idea what the logic behind this is, but I thought that we should keep it.

Larry