Skip to contentSkip to conversation

Firewire camera and PCMCIA card under Debian

DISCUSSION ali shahrokni 2 participants 2 messages Sep 11, 2006 – Sep 12, 2006

lore
Share & tools
lore
#0 lore raw

Hello,
I am trying to connect a unibrain firewire camera to my T40 thinkpad using a PCMCIA firecard. I am running debian testing and kernel 2.6.15.
The card is detected and the output of dmeg follows but the camera doesn't even turn on and nothing happens when I connect it to the card! Any help would be greatly appreciated. Cheers,
Ali

ieee1394: raw1394: /dev/raw1394 device initialized
video1394: Installed video1394 module
usb 2-2: new full speed USB device using uhci_hcd and address 3
pccard: card ejected from slot 1
ieee1394: Node removed: ID:BUS[0-00:1023] GUID[0814435800000528]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
pccard: CardBus card inserted into slot 1
PCI: Enabling device 0000:07:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:07:00.0 to 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[c4004000-c40047ff] Max Packet=[2048]
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0814435800000528]

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs

#1 lore raw
Quoted 5 lines · ali shahrokni

Hello,
I am trying to connect a unibrain firewire camera to my T40 thinkpad using a PCMCIA firecard. I am running debian testing and kernel 2.6.15.
The card is detected and the output of dmeg follows but the camera doesn't even turn on and nothing happens when I connect it to the card! Any help would be greatly appreciated. Cheers,
Ali

Ali --

I looked at http://www.linux1394.org/. Their "compatibility list" puts the Fire-i digital camera and the Fire-i400 both in the "Works Great" class. Both use ohci1394, which your dmesg output below says you are loading.

The Unibrain page on "detailed product specs" mentions the possibility of the camera needing a separate DC input to work. It says:

"Fire-i™ Digital Camera is provided with a DC power input jack connector, that can be used when the FireWire connection does not provide DC power. This happens typically:

"* when the FireWire bus is converted to a 4-pin connection
"* when, in 6-pin, no powering device is present, even from the
FireWire interface. This is the case when using CardBus FireWire adapters or on some laptops with built-in interface"

The "doesn't even turn on" part of your message makes me suspect that you have this power problem ... not a Linux problem as such but a hardware problem. Only a guess, though.

If that's it, there is info on using DC adapters at http://www.unibrain.com/Products/VisionImg/tSpec_Fire_i_DC.htm

Quoted 16 lines

ieee1394: raw1394: /dev/raw1394 device initialized
video1394: Installed video1394 module
usb 2-2: new full speed USB device using uhci_hcd and address 3
pccard: card ejected from slot 1
ieee1394: Node removed: ID:BUS[0-00:1023] GUID[0814435800000528]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394: fw-host0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
pccard: CardBus card inserted into slot 1
PCI: Enabling device 0000:07:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:07:00.0 to 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[c4004000-c40047ff] Max Packet=[2048]
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0814435800000528]

Quoted 6 lines

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs