u-boot as second monitor
Hi,
I have a TQM823L board that comes with the Mon8xx monitor. I have read about how to install uboot over Mon8xx, but I would like to know if it is possible to generate u-boot for a different flash address and call it after the Mon8xx boot. If so what should I change in the uboot code?
Thanks,
Francisco
Quoted 5 lines · Francisco Afonso
Hi,
I have a TQM823L board that comes with the Mon8xx monitor. I have read about how to install uboot over Mon8xx, but I would like to know if it is possible to generate u-boot for a different flash address and call
Yes, that's possible.
Quoted 1 line
it after the Mon8xx boot. If so what should I change in the uboot code?
One problem is if Mon8xx initializes the hardware before calling U-Boot. U-Boot may not work if some hardware is already initialized before U-Boot starts. I have this problem with my BDI-2000 hardware debugger. If I let the BDI initialize flash (so that I can write to it), U-Boot will hang when it starts.
Signature · 2 lines
Timur Tabi Linux Kernel Developer @ Freescale
Quoted 5 lines · In message <[email protected]> you wrote:
I have a TQM823L board that comes with the Mon8xx monitor. I have read about how to install uboot over Mon8xx, but I would like to know if it is possible to generate u-boot for a different flash address and call it after the Mon8xx boot. If so what should I change in the uboot code?
No, this is not possible. There is no reason to keep MON8xx after installing U-Boot anyway. You won't ever need or want it again.
Best regards,
Wolfgang Denk
Signature · 5 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "If you'll excuse me a minute, I'm going to have a cup of coffee." - broadcast from Apollo 11's LEM, "Eagle", to Johnson Space Center, Houston July 20, 1969, 7:27 P.M.
Quoted 6 lines · In message <[email protected]> you wrote:
Quoted 4 lines
I have a TQM823L board that comes with the Mon8xx monitor. I have read about how to install uboot over Mon8xx, but I would like to know if it is possible to generate u-boot for a different flash address and call
Yes, that's possible.
This is NOT a supported mode of operation.
Best regards,
Wolfgang Denk
Signature · 4 lines
Software Engineering: Embedded and Realtime Systems, Embedded Linux Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The human mind ordinarily operates at only ten percent of its capacity. The rest is overhead for the operating system.
Wolfgang Denk skrev:
Quoted 9 lines
Quoted 4 lines · In message <[email protected]> you wrote:
I have a TQM823L board that comes with the Mon8xx monitor. I have read about how to install uboot over Mon8xx, but I would like to know if it is possible to generate u-boot for a different flash address and call it after the Mon8xx boot. If so what should I change in the uboot code?
No, this is not possible. There is no reason to keep MON8xx after installing U-Boot anyway. You won't ever need or want it again.
It is possible, This is how you boot the AT91RM9200 from dataflash.
First the bootROM is executed and this loads "Dataflashboot.bin" into internal SRAM and jumps to the beginning. Dataflashboot.bin loads U-Boot into SDRAM and jumps into U-boot. And no, you cannot replace Dataflashboot.bin with U-boot (unless you manage to shrink it to 12 kByte)
The at91rm9200dk needs a little tweaking for this to work. Cannot link it to 0x00000000.
/Ulf
Quoted 4 lines
Best regards,
Wolfgang Denk
-------------- next part --------------
A non-text attachment was scrubbed...
Name: ulf.vcf
Type: text/x-vcard
Size: 297 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20061107/d03e153d/attachment.vcf