Skip to contentSkip to conversation

suspend a device to save energy

DISCUSSION Cacy Rodney 1 participant 1 message Nov 13, 2006 ACPI

lore
Share & tools
lore
#0 lore raw

Hi,
I tried to suspend a device (ide cdrom) to save energy in my laptop. I did it using:

echo -n 2 >/sys/devices/pci0000\:00/0000\:00\:1f.1/power/state

I have got a message in syslog that the device is suspended but no decrease of energy consumption. The configuration of the PCI was not changed. It seams that the device is off only for system but still physically enabled. The question is: Does the ACPI is responsible for turning off the device (and how to do that) or I have to write extension for driver?

This is report of lspci for the device:

bash-3.00# lspci -xxx -s 0:1f.1
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00: 86 80 df 27 05 00 80 02 02 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 11 18 00 00 00 00 00 00 00 00 00 00 4d 10 e6 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 02 00 00
40: 07 a3 00 00 00 00 00 00 01 00 02 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

As I said the suspend does not change anything. Contrary, windows operating system is able to shut down the device and it changes the state from:
(running)

PCI Bus 0
1f:1 8086:27df.02 Cmd[0005:i.b...] Sts[0280:.....] Intel IDE Controller SubID:104d:81e6

     cf8:8000f900  IntPin:2  IntLine:ff  Rom:0  cis:0  cap:0
     IO[0]:1          IO[1]:1          IO[2]:1          

IO[3]:1 IO[4]:1811
00: 27df8086 02800005 01018a02 00000000
10: 00000001 00000001 00000001 00000001
20: 00001811 00000000 00000000 81e6104d
30: 00000000 00000000 00000000 000002ff 40: 0000a347 00000000 00020001 00000000 50: 00000000 00000000 00000000 00000000 60: 00000000 00000000 00000000 00000000 70: 00000000 00000000 00000000 00000000 80: 00000000 00000000 00000000 00000000 90: 00000000 00000000 00000000 00000000
a0: 00000000 00000000 00000000 00000000
b0: 00000000 00000000 00000000 00000000
c0: 00000000 00000003 00000000 00000000
d0: 00000000 00000000 00000000 00000000
e0: 00000000 00000000 00000000 00000000
f0: 00000000 00000000 00020f86 00000000

to (disabled)

1f:1 8086:27df.02 Cmd[0000:......] Sts[0288:.....] Intel IDE Controller SubID:104d:81e6

     cf8:8000f900  IntPin:2  IntLine:ff  Rom:0  cis:0  cap:0
     IO[0]:1          IO[1]:1          IO[2]:1          
IO[3]:1          IO[4]:1811      
 00:  27df8086 02880000 01018a02 00000000
 10:  00000001 00000001 00000001 00000001
 20:  00001811 00000000 00000000 81e6104d
 30:  00000000 00000000 00000000 000002ff

40: 0000a345 00000000 00020001 00000000 50: 00000000 00010000 00000000 00000000 60: 00000000 00000000 00000000 00000000 70: 00000000 00000000 00000000 00000000 80: 00000000 00000000 00000000 00000000 90: 00000000 00000000 00000000 00000000
a0: 00000000 00000000 00000000 00000000
b0: 00000000 00000000 00000000 00000000
c0: 00000000 00000003 00000000 00000000
d0: 00000000 00000000 00000000 00000000
e0: 00000000 00000000 00000000 00000000
f0: 00000000 00000000 00020f86 00000000

I found a recipt how to off the pci (intel manual for ich7-m) but I have no idea where it should be in ACPI (I donot know much about it) or in a driver.

Cacy