Skip to contentSkip to conversation

2.6.19-rc5-mm2 : usb keeps resetting usb keyboard.

DISCUSSION Ed Sweetman 3 participants 4 messages Nov 25, 2006

lore
Share & tools
lore
#0 lore raw

I just upgraded from a ps2 keyboard to usb and have been getting these messages seemingly randomly, which also corresponds to whatever key i'm pressing at the time they occur to act like it's stuck down.

usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3

(repeated a few hundred times )

The keyboard is detected as
Bus 002 Device 002: ID 1267:0103 Logic3 / SpectraVideo plc

Any further input needed?

below is my lspci output : Attached is more verbose output.

00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2) 00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2)
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] (rev a2)
05:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02) 05:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)

00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. Unknown device 815a
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Capabilities: [e0] HyperTransport: MSI Mapping

00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0

00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)

	Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
	Flags: 66MHz, fast devsel, IRQ 255
	I/O ports at e400 [size=32]
	I/O ports at 4c00 [size=64]
	I/O ports at 4c40 [size=64]
	Capabilities: [44] Power Management version 2

00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at c8104000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2

00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2

00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)

	Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
	I/O ports at dc00 [size=256]
	I/O ports at e000 [size=256]
	Memory at c8103000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP])

	Subsystem: Unknown device f043:815a
	Flags: bus master, 66MHz, fast devsel, latency 0
	[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
	[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
	I/O ports at f000 [size=16]
	Capabilities: [44] Power Management version 2

00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])

	Subsystem: ASUSTeK Computer Inc. Unknown device 815a
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
	I/O ports at 09f0 [size=8]
	I/O ports at 0bf0 [size=4]
	I/O ports at 0970 [size=8]
	I/O ports at 0b70 [size=4]
	I/O ports at d800 [size=16]
	Memory at c8102000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])

	Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
	I/O ports at 09e0 [size=8]
	I/O ports at 0be0 [size=4]
	I/O ports at 0960 [size=8]
	I/O ports at 0b60 [size=4]
	I/O ports at c400 [size=16]
	Memory at c8101000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=128 Prefetchable memory behind bridge: c8000000-c80fffff

00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at c8100000 (32-bit, non-prefetchable) [size=4K] I/O ports at b000 [size=8]
Capabilities: [44] Power Management version 2

00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel

00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel

00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel

00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: c0000000-c7ffffff
Prefetchable memory behind bridge: 00000000b0000000-00000000bfffffff
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel

01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] (rev a2) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 81b0
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at c0000000 (32-bit, non-prefetchable) [size=64M]
Memory at b0000000 (64-bit, prefetchable) [size=256M]
Memory at c4000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at c5000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [78] Express Endpoint IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting

05:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV Series
Flags: bus master, medium devsel, latency 32, IRQ 255
Memory at c8000000 (32-bit, prefetchable) [size=4K]

05:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV Series
Flags: bus master, medium devsel, latency 32, IRQ 255
Memory at c8001000 (32-bit, prefetchable) [size=4K]

#1 lore raw
Quoted 12 lines · Ed Sweetman

I just upgraded from a ps2 keyboard to usb and have been getting these messages seemingly randomly, which also corresponds to whatever key i'm pressing at the time they occur to act like it's stuck down.

usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3

Quoted 2 lines

(repeated a few hundred times )

All the data below doesn't point to the culprit.

I also have this, and I'd bet the common point is going to be an M$ wireless mouse like I have. The mouse works ok as near as I can tell, so I'm not sure of the exact cause.

To verify, unplug the receiver for that mouse, wait 5secs, and plug it back in, which if thats it should move the mouse, and the log message to a higher number on the usb tree.

Also, FWIW dear lkml readers, my logs have been contaminated with this since about a year ago, running kernel.org kernels on an FC2 system, but using the latest FC6 non-xen kernel.

Quoted 1 line

From an lsusb -v:

----------
Bus 002 Device 003: ID 045e:008c Microsoft Corp. Wireless Intellimouse Explorer 2.0
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x045e Microsoft Corp.
  idProduct          0x008c Wireless Intellimouse Explorer 2.0
  bcdDevice            0.57
  iManufacturer           1 Microsoft
  iProduct                2 Microsoft Wireless Optical Mouse 1.0A
  iSerial                 0
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 50mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 209
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
-------------------

How close am I in this suposition?

Signature · 7 lines
Cheers, Gene
"There are four boxes to be used in defense of liberty:
 soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
Yahoo.com and AOL/TW attorneys please note, additions to the above
message by Gene Heskett are:
Copyright 2006 by Maurice Eugene Heskett, all rights reserved.
#2 lore raw
Quoted 17 lines · Gene Heskett
Quoted 12 lines · Ed Sweetman

I just upgraded from a ps2 keyboard to usb and have been getting these messages seemingly randomly, which also corresponds to whatever key i'm pressing at the time they occur to act like it's stuck down.

usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3

Quoted 3 lines

(repeated a few hundred times )

Quoted 8 lines

All the data below doesn't point to the culprit.

I also have this, and I'd bet the common point is going to be an M$ wireless mouse like I have. The mouse works ok as near as I can tell, so I'm not sure of the exact cause.

To verify, unplug the receiver for that mouse, wait 5secs, and plug it back in, which if thats it should move the mouse, and the log message to a higher number on the usb tree.

Also, FWIW dear lkml readers, my logs have been contaminated with this since about a year ago, running kernel.org kernels on an FC2 system, but using the latest FC6 non-xen kernel.

I dont have a wireless usb mouse or any hardware from microsoft running. My usb mouse is a standard logitech that i've been using for a couple years. I haven't had these errors in my log before installing my usb keyboard.

These are the only usb devices in the system.

below is my lsusb -v. For what it's worth.

Bus 002 Device 003: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

 bDeviceClass            0 (Defined at Interface level)
 bDeviceSubClass         0
 bDeviceProtocol         0
 bMaxPacketSize0         8
 idVendor           0x046d Logitech, Inc.
 idProduct          0xc00c Optical Wheel Mouse
 bcdDevice            6.10
 iManufacturer           1 Logitech
 iProduct                2 USB Mouse
 iSerial                 0
 bNumConfigurations      1
 Configuration Descriptor:
   bLength                 9
   bDescriptorType         2
   wTotalLength           34
   bNumInterfaces          1
   bConfigurationValue     1
   iConfiguration          0
   bmAttributes         0xa0
     (Bus Powered)
     Remote Wakeup
   MaxPower              100mA
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        0
     bAlternateSetting       0
     bNumEndpoints           1
     bInterfaceClass         3 Human Interface Devices
     bInterfaceSubClass      1 Boot Interface Subclass
     bInterfaceProtocol      2 Mouse
     iInterface              0

HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 68
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)

Bus 002 Device 002: ID 1267:0103 Logic3 / SpectraVideo plc Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

 bDeviceClass            0 (Defined at Interface level)
 bDeviceSubClass         0
 bDeviceProtocol         0
 bMaxPacketSize0         8
 idVendor           0x1267 Logic3 / SpectraVideo plc
 idProduct          0x0103
 bcdDevice            1.01
 iManufacturer           0
 iProduct                0
 iSerial                 0
 bNumConfigurations      1
 Configuration Descriptor:
   bLength                 9
   bDescriptorType         2
   wTotalLength           59
   bNumInterfaces          2
   bConfigurationValue     1
   iConfiguration          0
   bmAttributes         0xa0
     (Bus Powered)
     Remote Wakeup
   MaxPower              100mA
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        0
     bAlternateSetting       0
     bNumEndpoints           1
     bInterfaceClass         3 Human Interface Devices
     bInterfaceSubClass      1 Boot Interface Subclass
     bInterfaceProtocol      1 Keyboard
     iInterface              0
       HID Device Descriptor:
         bLength                 9
         bDescriptorType        33
         bcdHID               1.10
         bCountryCode            0 Not supported
         bNumDescriptors         1
         bDescriptorType        34 Report
         wDescriptorLength      54
        Report Descriptors:
          ** UNAVAILABLE **
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x81  EP 1 IN
       bmAttributes            3
         Transfer Type            Interrupt
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0008  1x 8 bytes
       bInterval              10
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        1
     bAlternateSetting       0
     bNumEndpoints           1
     bInterfaceClass         3 Human Interface Devices
     bInterfaceSubClass      0 No Subclass
     bInterfaceProtocol      0 None
     iInterface              0

HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 52
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0003 1x 3 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)

Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

 bDeviceClass            9 Hub
 bDeviceSubClass         0 Unused
 bDeviceProtocol         0 Full speed hub
 bMaxPacketSize0        64
 idVendor           0x0000
 idProduct          0x0000
 bcdDevice            2.06
 iManufacturer           3 Linux 2.6.19-rc5-mm2 ohci_hcd
 iProduct                2 OHCI Host Controller
 iSerial                 1 0000:00:02.0
 bNumConfigurations      1
 Configuration Descriptor:
   bLength                 9
   bDescriptorType         2
   wTotalLength           25
   bNumInterfaces          1
   bConfigurationValue     1
   iConfiguration          0
   bmAttributes         0xe0
     Self Powered
     Remote Wakeup
   MaxPower                0mA
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        0
     bAlternateSetting       0
     bNumEndpoints           1
     bInterfaceClass         9 Hub
     bInterfaceSubClass      0 Unused
     bInterfaceProtocol      0 Full speed hub
     iInterface              0

Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:

 bLength              11
 bDescriptorType      41
 nNbrPorts            10

wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0303 lowspeed power enable connect
Port 2: 0000.0303 lowspeed power enable connect
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Port 9: 0000.0100 power
Port 10: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

 bDeviceClass            9 Hub
 bDeviceSubClass         0 Unused
 bDeviceProtocol         1 Single TT
 bMaxPacketSize0        64
 idVendor           0x0000
 idProduct          0x0000
 bcdDevice            2.06
 iManufacturer           3 Linux 2.6.19-rc5-mm2 ehci_hcd
 iProduct                2 EHCI Host Controller
 iSerial                 1 0000:00:02.1
 bNumConfigurations      1
 Configuration Descriptor:
   bLength                 9
   bDescriptorType         2
   wTotalLength           25
   bNumInterfaces          1
   bConfigurationValue     1
   iConfiguration          0
   bmAttributes         0xe0
     Self Powered
     Remote Wakeup
   MaxPower                0mA
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        0
     bAlternateSetting       0
     bNumEndpoints           1
     bInterfaceClass         9 Hub
     bInterfaceSubClass      0 Unused
     bInterfaceProtocol      0 Full speed hub
     iInterface              0

Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:

 bLength              11
 bDescriptorType      41
 nNbrPorts            10

wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0000
Port 2: 0000.0000
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Port 9: 0000.0100 power
Port 10: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Quoted 63 lines
Quoted 1 line

From an lsusb -v:

----------
Bus 002 Device 003: ID 045e:008c Microsoft Corp. Wireless Intellimouse Explorer 2.0 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x045e Microsoft Corp.
  idProduct          0x008c Wireless Intellimouse Explorer 2.0
  bcdDevice            0.57
  iManufacturer           1 Microsoft
  iProduct                2 Microsoft Wireless Optical Mouse 1.0A
  iSerial                 0
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 50mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 209
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
-------------------

How close am I in this suposition?

#3 lore raw
Quoted 32 lines · Ed Sweetman
Quoted 23 lines · Gene Heskett
Quoted 12 lines · Ed Sweetman

I just upgraded from a ps2 keyboard to usb and have been getting these messages seemingly randomly, which also corresponds to whatever key i'm pressing at the time they occur to act like it's stuck down.

usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3 usb 2-2: reset low speed USB device using ohci_hcd and address 3

Quoted 3 lines

(repeated a few hundred times )

All the data below doesn't point to the culprit.

I also have this, and I'd bet the common point is going to be an M$ wireless mouse like I have. The mouse works ok as near as I can tell, so I'm not sure of the exact cause.

Quoted 8 lines

To verify, unplug the receiver for that mouse, wait 5secs, and plug it back in, which if thats it should move the mouse, and the log message to a higher number on the usb tree.

Also, FWIW dear lkml readers, my logs have been contaminated with this since about a year ago, running kernel.org kernels on an FC2 system, but using the latest FC6 non-xen kernel.

Quoted 6 lines

I dont have a wireless usb mouse or any hardware from microsoft running. My usb mouse is a standard logitech that i've been using for a
couple years. I haven't had these errors in my log before installing
my usb keyboard.

These are the only usb devices in the system.

Complaining about the messages in your log doesn't do any good. You need to address the real problem, which is why your keyboard keeps needing to be reset.

To get more information about the problem, you could try building a kernel with CONFIG_USB_DEBUG turned on. Perhaps even more informative, you could use the usbmon facility (see the instructions in Documentation/usb/usbmon.txt). To keep the trace simple, you should unplug all USB devices except the one you're testing.

Alan Stern