Skip to contentSkip to conversation

HP dv9000t battery discharge rate

DISCUSSION Sergey Basmanov 2 participants 2 messages Dec 4, 2006 – Dec 5, 2006 ACPI

lore
Share & tools
lore
#0 lore raw

Hi,
Was looking how to get battery discharge rate on this laptop. This is part of DSDT:

           Name (PBST, Package (0x04)
           {
               0x00,
               0xFFFFFFFF,
               0xFFFFFFFF,
               0x2710
           })

...

           Method (_BST, 0, NotSerialized)
           {
               If (ECON)
               {
                   If (\_SB.PCI0.LPCB.EC0.MBTS)
                   {
                       UPBS ()
                   }
                   Else
                   {
                       IVBS ()
                   }
               }
               Else
               {
                   IVBS ()
               }

               Return (PBST)
           }
...
           Method (UPBS, 0, NotSerialized)
           {
               Store (\_SB.PCI0.LPCB.EC0.MBRM, Local5)
               If (LNot (And (Local5, 0x8000)))
               {
                   ShiftRight (Local5, 0x05, Local5)
                   ShiftLeft (Local5, 0x05, Local5)
                   If (LNotEqual (Local5, DerefOf (Index (PBST, 0x02))))
                   {
                       Store (Local5, Index (PBST, 0x02))
                   }
               }

               Store (\_SB.PCI0.LPCB.EC0.MBCV, Index (PBST, 0x03))
               Store (\_SB.PCI0.LPCB.EC0.MBST, Index (PBST, 0x00))
               Store (\_SB.PCI0.LPCB.EC0.BA1C, BCAP)
           }

and method IVBS just stores default values into PBST.
So, I'm not familiar with iasl and rest, but if I understand right, UPBS method is used in case when battery connected and known to system. In UPBS method I don't see any code that updates PBST at 0x01 (discharge_rate). HP support says that sensor is present in system. Any ideas where this sensor located and how can I get discharge rate visible in ACPI (kernel 2.6.18.2)?

PS: Please, reply to e-mail directly because I'm not subscribed to this list. Thank You..

#1 lore raw
Quoted 51 lines · Sergey Basmanov

Hi,
Was looking how to get battery discharge rate on this laptop. This is part of DSDT:

           Name (PBST, Package (0x04)
           {
               0x00,
               0xFFFFFFFF,
               0xFFFFFFFF,
               0x2710
           })

...

           Method (_BST, 0, NotSerialized)
           {
               If (ECON)
               {
                   If (\_SB.PCI0.LPCB.EC0.MBTS)
                   {
                       UPBS ()
                   }
                   Else
                   {
                       IVBS ()
                   }
               }
               Else
               {
                   IVBS ()
               }

               Return (PBST)
           }
...
           Method (UPBS, 0, NotSerialized)
           {
               Store (\_SB.PCI0.LPCB.EC0.MBRM, Local5)
               If (LNot (And (Local5, 0x8000)))
               {
                   ShiftRight (Local5, 0x05, Local5)
                   ShiftLeft (Local5, 0x05, Local5)
                   If (LNotEqual (Local5, DerefOf (Index (PBST, 0x02))))
                   {
                       Store (Local5, Index (PBST, 0x02))
                   }
               }

               Store (\_SB.PCI0.LPCB.EC0.MBCV, Index (PBST, 0x03))
               Store (\_SB.PCI0.LPCB.EC0.MBST, Index (PBST, 0x00))
               Store (\_SB.PCI0.LPCB.EC0.BA1C, BCAP)
           }
Quoted 7 lines

and method IVBS just stores default values into PBST.
So, I'm not familiar with iasl and rest, but if I understand right, UPBS method is used in case when battery connected and known to system. In UPBS method I don't see any code that updates PBST at 0x01 (discharge_rate). HP support says that sensor is present in system. Any ideas where this sensor located and how can I get discharge rate visible in ACPI (kernel 2.6.18.2)?

It's likely under the embedded controller. If you give me the whole OperationRegion() and the Field() for that one it might be possible I could have a hint to get it.

It should be something like that:

Device (EC0)

{
	...
	...
	OperationRegion(XXXX, EmbeddedControl, 0x00, 0xFF)
	Field(XXXX, ByteAcc, ..., ...)
	{
		...
		...
	}
	...
}

I'll need all the Field with the same name (here XXXX).

Or alternatively send to me the whole ASL.

Cheers,

Signature · 4 lines
Bruno Ducrot

--  Which is worse:  ignorance or apathy?
--  Don't know.  Don't care.