Skip to contentSkip to conversation

DMA errors with HTP370 IDE in <= 2.6.18.2

DISCUSSION Michael Bueker 2 participants 2 messages Jan 8, 2007 – Jan 9, 2007 libata

lore
Share & tools
lore
#0 lore raw

Hello,

[please CC me upon replying - thank you]

I have a Highpoint 370 PCI IDE controller, and both my 2.6.18.2 and Knoppix 5's 2.6.17 display the following messages:

Quoted 47 lines

HPT370: IDE controller at PCI slot 0000:01:09.0
HPT370: chipset revision 3
HPT370: 100% native mode on irq 11
HPT37X: using 33MHz PCI clock

    ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:DMA, hdf:DMA
HPT37X: using 33MHz PCI clock
    ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:pio, hdh:pio

Probing IDE interface ide2...
hde: ST340823A, ATA DISK drive
hdf: ExcelStor Technology J840, ATA DISK drive
ide2 at 0x9000-0x9007,0x9402 on irq 11
Probing IDE interface ide3...
hdg: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
ide3 at 0x9800-0x9807,0x9c02 on irq 11
hde: max request size: 128KiB
hde: 78165360 sectors (40020 MB) w/1024KiB Cache, CHS=65535/16/63, UDMA(100)
hde: cache flushes not supported
hde:<4>hde: dma_timer_expiry: dma status == 0x61
hde: DMA timeout error
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: dma timeout error: status=0x80 { Busy }
ide: failed opcode was: unknown
hde: DMA disabled
hdf: DMA disabled
ide2: reset: success
hde1 hde2 <<4>hde: dma_timer_expiry: dma status == 0x21
hde: DMA timeout error
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: dma timeout error: status=0x80 { Busy }
ide: failed opcode was: unknown
hde: DMA disabled
ide2: reset: success
hde5<4>hde: dma_timer_expiry: dma status == 0x21
hde: DMA timeout error
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: dma timeout error: status=0x80 { Busy }
ide: failed opcode was: unknown
hde: DMA disabled
ide2: reset: success
hde6 >
hdf: max request size: 512KiB
hdf: 80418240 sectors (41174 MB) w/1719KiB Cache, CHS=16383/255/63
hdf: cache flushes supported
hdf: unknown partition table

Quoted 8 lines

hde: dma_timer_expiry: dma status == 0x21
hde: DMA timeout error
hde: 0 bytes in FIFO
hde: timeout waiting for DMA
hde: dma timeout error: status=0x80 { Busy }
ide: failed opcode was: unknown
hde: DMA disabled
ide2: reset: success

(hdf is naked, there's no error in partition detection)

The same messages appear when manually trying to enable DMA with hdparm. The hdparm reading of hde is:

Quoted 9 lines

/dev/hde:

 multcount    = 16 (on)
 IO_support   =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  0 (off)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 65535/16/63, sectors = 78165360, start = 0

hda, which is on the mainboard controller and works as hde used to as well, reads:

Quoted 9 lines

/dev/hda:

 multcount    = 16 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 65535/16/63, sectors = 117231408, start = 0

In the controller's setup utility, I can choose access modes. If i switch it from UDMA5 to PIO0, the only difference during boot is:

Quoted 1 line

ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio, hdf:pio

instead of

Quoted 1 line

ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:DMA, hdf:DMA

Please help me getting DMA to work with this controller.

Thanks in advance,
~Mik

Signature · 4 lines
So, how can you tell me you're lonely?
And say that you don't have no life?
Let me take you by the hand and show you all the geeks of London
I'll show you something to make you change your mind!
#1 lore raw
Quoted 2 lines · Michael Bueker

In the controller's setup utility, I can choose access modes. If i switch it from UDMA5 to PIO0, the only difference during boot is:

PIO0 is outrageously slow, use PIO4 (very slow as well but at least
somewhat faster). Anyway, this won't help with Linux...

Quoted 5 lines
Quoted 1 line

ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio, hdf:pio

instead of

Quoted 1 line

ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:DMA, hdf:DMA

You should specify the option ide=nodma to the kernel to disable IDE core
from using DMA.

Quoted 1 line

Please help me getting DMA to work with this controller.

For starters, please try the driver from 2.6.20-rc1 and (if that doesn't
help) from the -mm tree. I rewrote it and it's working OK on at least my HPT370...

Quoted 2 lines

Thanks in advance,
~Mik

WBR, Sergei