Skip to contentSkip to conversation

ACPI C and P states on Conroe

DISCUSSION Joe Harvell 2 participants 2 messages Jan 30, 2007

lore
Share & tools
lore
#0 lore raw

I am trying to enable all the power saving features I can on my Conroe E6600. After much searching on the web, I am a little confused about the Linux kernel support for ACPI on the Conroe.

Here is my setup:
Intel Core2 Duo E6600
Asus P5-B Deluxe board (Intel P965).
I am running a Gentoo kernel based on 2.6.19.4.

I have managed to enable EIST using cpufreq with the speedstep-centrino driver. But my understanding from browsing the ACPI spec is that this is still within C0, i.e. not much power savings.

Here are my questions:

1) For P states, which cpufreq driver should I be using? I've heard speedstep-centrino is deprecated (but only some aspects of it) that are being moved into acpi-cpufreq. But I can't get acpi-cpufreq to load in my kernel version. Also, I would have thought speedstep-ich would be the driver, just based on the name. How do I know (other than trying all modules to see which one loads) which one I should be using?
2) What kind of support for C1-C3 does the Conroe have? The ACPI spec says C2 and C3 require chipset support on the motherboard. Does P965 have that. Does it matter between boards (e.g. P5B)?
3) What versions of the kernel support C1-C3 states? What kernel options are germane to this? What libraries/tools are involved?

---
Joe Harvell

#1 lore raw

C0 is the state when processor is executing instruction. C1-C3 is the state that kernel puts the CPU into when there is nothing to run (idle loop).
C1 is supported by all processors and it is entered either by using "hlt" or "mwait" instructions. You don't have to do anything to enable this. It should be getting used already (unless you are using "idle=poll" in which case C1 will not be used).
C2 and C3 however are not supported on all processors/platforms typically. If it is supported, BIOS will export these states information to OS, through ACPI and kernel acpi processor module will enable those states. As long as you have CONFIG_ACPI_PROCESSOR enabled, this support will be built in and should get enabled (if your platform supports this feature). There are no magic setup to enable this. If present, you will see info about these C-states here - /proc/acpi/processor/CPU*/power

-Venki

Quoted 46 lines

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Joe Harvell
Sent: Tuesday, January 30, 2007 9:34 AM
To: [email protected]
Subject: ACPI C and P states on Conroe

I am trying to enable all the power saving features I can on my Conroe E6600. After much searching on the web, I am a little confused about the Linux kernel support for ACPI on the Conroe.

Here is my setup:
Intel Core2 Duo E6600
Asus P5-B Deluxe board (Intel P965).
I am running a Gentoo kernel based on 2.6.19.4.

I have managed to enable EIST using cpufreq with the speedstep-centrino
driver. But my understanding from browsing the ACPI spec is that this is still within C0, i.e. not much power savings.

Here are my questions:

1) For P states, which cpufreq driver should I be using? I've heard speedstep-centrino is deprecated (but only some aspects of it) that are
being moved into acpi-cpufreq. But I can't get acpi-cpufreq to load in
my kernel version. Also, I would have thought speedstep-ich would be the driver, just based on the name. How do I know (other than trying all modules to see which one loads) which one I should be using?
2) What kind of support for C1-C3 does the Conroe have? The ACPI spec says C2 and C3 require chipset support on the motherboard. Does P965 have that. Does it matter between boards (e.g. P5B)?
3) What versions of the kernel support C1-C3 states? What kernel options are germane to this? What libraries/tools are involved?

---
Joe Harvell
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/