Skip to contentSkip to conversation

cat, cp operations for tty driver (like for char one)

DISCUSSION Mockern 2 participants 5 messages Feb 15, 2007 – Feb 16, 2007

lore
Share & tools
lore

Mockern

author
#0 lore raw

I have a question about linux tty driver

how to support cp, cat operations in tty driver (like tiny_tty)? (e.g. echo "hello tty" > /dev/ttyS3, cat < ttyS10 etc)

There a lot of examples with char drivers, but I could not find it for tty Linux driver.

#1 lore raw
Quoted 7 lines · Mockern

I have a question about linux tty driver

how to support cp, cat operations in tty driver (like tiny_tty)? (e.g. echo "hello tty" > /dev/ttyS3, cat < ttyS10 etc)

There a lot of examples with char drivers, but I could not find it for tty Linux driver.

It works out of the box. Just keep hardware flow-control turned off if there are no receivers connected to the output port. Also, you need to set up the port's baud-rate and (usually) to make it transparent to control characters (man tc-get/set-attr).

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.61 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

author
#2 lore raw

Thanx for your respond.

Does it mean I have to change nothing in my tty driver (based on serial_core.c) to use: cat and cp? No "nonstandard " special functions to implement?

Quoted 27 lines · Mockern
Quoted 8 lines

I have a question about linux tty driver

how to support cp, cat operations in tty driver (like tiny_tty)? (e.g. echo "hello tty" > /dev/ttyS3, cat < ttyS10 etc)

There a lot of examples with char drivers, but I could not find it for tty Linux driver.

It works out of the box. Just keep hardware flow-control turned off if there are no receivers connected to the output port. Also, you need to set up the port's baud-rate and (usually) to make it transparent to control characters (man tc-get/set-attr).

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.61 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

#3 lore raw
Quoted 6 lines · Mockern

Thanx for your respond.

Does it mean I have to change nothing in my tty driver (based on serial_core.c) to use: cat and cp? No "nonstandard " special functions to implement?

Change nothing. It you are making your own, make sure your iocl() function returns the same kinds of errors as the in-kernel one.

You can check out the existing in-kernel driver as:

strace cp filename /dev/ttyS0

Quoted 25 lines
Quoted 25 lines · Mockern
Quoted 8 lines

I have a question about linux tty driver

how to support cp, cat operations in tty driver (like tiny_tty)? (e.g. echo "hello tty" > /dev/ttyS3, cat < ttyS10 etc)

There a lot of examples with char drivers, but I could not find it for tty Linux driver.

It works out of the box. Just keep hardware flow-control turned off if there are no receivers connected to the output port. Also, you need to set up the port's baud-rate and (usually) to make it transparent to control characters (man tc-get/set-attr).

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.61 BogoMips). New book: http://www.AbominableFirebug.com/
_


Quoted 6 lines
Quoted 4 lines

****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5594.84 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

author
#4 lore raw

Thank you very much

Quoted 61 lines · Mockern
Quoted 7 lines

Thanx for your respond.

Does it mean I have to change nothing in my tty driver (based on serial_core.c) to use: cat and cp? No "nonstandard " special functions to implement?

Change nothing. It you are making your own, make sure your iocl() function returns the same kinds of errors as the in-kernel one.

You can check out the existing in-kernel driver as:

strace cp filename /dev/ttyS0

Quoted 25 lines
Quoted 25 lines · Mockern
Quoted 8 lines

I have a question about linux tty driver

how to support cp, cat operations in tty driver (like tiny_tty)? (e.g. echo "hello tty" > /dev/ttyS3, cat < ttyS10 etc)

There a lot of examples with char drivers, but I could not find it for tty Linux driver.

It works out of the box. Just keep hardware flow-control turned off if there are no receivers connected to the output port. Also, you need to set up the port's baud-rate and (usually) to make it transparent to control characters (man tc-get/set-attr).

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.61 BogoMips). New book: http://www.AbominableFirebug.com/
_


Quoted 6 lines
Quoted 4 lines

****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5594.84 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

Signature · 1 line
Сегодня удачный день, чтобы завести почту на Яндексе http://mail.yandex.ru