Skip to contentSkip to conversation

Newbie: Route some traffic through a pptp tunnel

LARTC Mogens Kjaer 2 participants 2 messages May 17, 2007

lore
Share & tools
lore
#0 lore raw

I have a centos 4 i386 machine that works like a
router (iptables filter, NAT) with two NIC's.

One NIC is connected to my ISP (100 Mbit FTTH),
I get a DHCP assigned public IP that changes
"sometimes". Most incoming ports are blocked
by my ISP.

In order to get a fixed IP and open ports, I
have to set up a PPTP tunnel to the ISP.

The default gw and the NAT'ing goes to this tunnel.

This is the output of ifconfig:

eth0 Link encap:Ethernet HWaddr 00:80:C8:EA:88:A7

           inet addr:86.48.47.147  Bcast:86.48.47.255  Mask:255.255.254.0
           inet6 addr: fe80::280:c8ff:feea:88a7/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:8083596 errors:0 dropped:0 overruns:0 frame:0
           TX packets:3408048 errors:22 dropped:0 overruns:22 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1538901914 (1.4 GiB)  TX bytes:519514046 (495.4 MiB)
           Interrupt:169 Base address:0x4000

eth1 Link encap:Ethernet HWaddr 00:12:79:A0:3D:7E

           inet addr:192.168.4.1  Bcast:192.168.4.255  Mask:255.255.255.0
           inet6 addr: fe80::212:79ff:fea0:3d7e/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:126264 errors:0 dropped:0 overruns:0 frame:0
           TX packets:155536 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:23156937 (22.0 MiB)  TX bytes:111015780 (105.8 MiB)
           Interrupt:177

lo Link encap:Local Loopback

           inet addr:127.0.0.1  Mask:255.0.0.0
           inet6 addr: ::1/128 Scope:Host
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:912424 errors:0 dropped:0 overruns:0 frame:0
           TX packets:912424 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:103397649 (98.6 MiB)  TX bytes:103397649 (98.6 MiB)

ppp0 Link encap:Point-to-Point Protocol

           inet addr:86.48.43.19  P-t-P:81.19.236.186  Mask:255.255.255.255
           UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1000  Metric:1
           RX packets:120948 errors:0 dropped:0 overruns:0 frame:0
           TX packets:109043 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:3
           RX bytes:80518167 (76.7 MiB)  TX bytes:37434930 (35.7 MiB)

This works today, my problem is that the tunneled traffic is slower than going through eth0 directly.

How can I:

1. Use the tunnel for incoming and outgoing mail and incoming http requests.
2. NAT traffic from eth1 to eth0, i.e. not through the tunnel
3. Local traffic from the router should access the internet through eth0, except for outgoing mails.

Mogens

Signature · 8 lines
Mogens Kjaer, Carlsberg A/S, Computer Department
Gamle Carlsberg Vej 10, DK-2500 Valby, Denmark
Phone: +45 33 27 53 25, Fax: +45 33 27 47 08
Email: [email protected] Homepage: http://www.crc.dk
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#1 lore raw

Mogens Kjaer написа:

Quoted 57 lines

I have a centos 4 i386 machine that works like a
router (iptables filter, NAT) with two NIC's.

One NIC is connected to my ISP (100 Mbit FTTH),
I get a DHCP assigned public IP that changes
"sometimes". Most incoming ports are blocked
by my ISP.

In order to get a fixed IP and open ports, I
have to set up a PPTP tunnel to the ISP.

The default gw and the NAT'ing goes to this tunnel.

This is the output of ifconfig:

eth0 Link encap:Ethernet HWaddr 00:80:C8:EA:88:A7 inet addr:86.48.47.147 Bcast:86.48.47.255 Mask:255.255.254.0 inet6 addr: fe80::280:c8ff:feea:88a7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8083596 errors:0 dropped:0 overruns:0 frame:0 TX packets:3408048 errors:22 dropped:0 overruns:22 carrier:0 collisions:0 txqueuelen:1000
RX bytes:1538901914 (1.4 GiB) TX bytes:519514046 (495.4 MiB) Interrupt:169 Base address:0x4000

eth1 Link encap:Ethernet HWaddr 00:12:79:A0:3D:7E inet addr:192.168.4.1 Bcast:192.168.4.255 Mask:255.255.255.0 inet6 addr: fe80::212:79ff:fea0:3d7e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:126264 errors:0 dropped:0 overruns:0 frame:0 TX packets:155536 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:23156937 (22.0 MiB) TX bytes:111015780 (105.8 MiB) Interrupt:177

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:912424 errors:0 dropped:0 overruns:0 frame:0 TX packets:912424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:103397649 (98.6 MiB) TX bytes:103397649 (98.6 MiB)

ppp0 Link encap:Point-to-Point Protocol
inet addr:86.48.43.19 P-t-P:81.19.236.186 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1000 Metric:1 RX packets:120948 errors:0 dropped:0 overruns:0 frame:0 TX packets:109043 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3
RX bytes:80518167 (76.7 MiB) TX bytes:37434930 (35.7 MiB)

This works today, my problem is that the tunneled traffic is slower than going through eth0 directly.

How can I:

Quoted 9 lines

1. Use the tunnel for incoming and outgoing mail and incoming http requests.
2. NAT traffic from eth1 to eth0, i.e. not through the tunnel
3. Local traffic from the router should access the internet through eth0, except for outgoing mails.

Mogens

You may find the ROUTE iptables target useful for this.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc