problems with faulty disks and superblocks 1.0, 1.1 and 1.2
Hello
I'm having problems with a RAID-1 configuration. I cannot re-add a disk that I've failed, because each time I do this, the re-added disk is still seen as failed. After some investigations, I found that this problem only occur when I create the RAID array with superblocks 1.0, 1.1 and 1.2.
With the superblock 0.90 I don't encounter this issue.
Here are the commands to easily reproduce the issue
mdadm -C /dev/md_d0 -e 1.0 -l 1 -n 2 -b internal -R /dev/sda /dev/sdb mdadm /dev/md_d0 -f /dev/sda
mdadm /dev/md_d0 -r /dev/sda
mdadm /dev/md_d0 -a /dev/sda
cat /proc/mdstat
The output of mdstat is:
Personalities : [raid1]md_d0 : active raid1 sda[0](F) sdb[1]
104849 blocks super 1.2 [2/1] [_U]
bitmap: 0/7 pages [0KB], 8KB chunkunused devices: <none>
I'm wondering if the way I'm failing and re-adding a disk is correct. Did I make something wrong?
If I change the superblock to "-e 0.90", there's no problem with this set of commands.
For now, I found a work-around with superblock 1.0 which consists in zeroing the superblock before re-adding the disk. But I suppose that doing so will force a full rebuild of the re-added disk, and I don't want this, because I'm using write-intent bitmaps.
I'm using mdadm - v2.5.6 on Debian Etch with kernel 2.6.18-4.
Bug or misunderstanding from myself? Any help would be appreciated :)
Thanks
Hubert
Quoted 25 lines · Hubert Verstraete
Hello
I'm having problems with a RAID-1 configuration. I cannot re-add a disk that I've failed, because each time I do this, the re-added disk is still seen as failed. After some investigations, I found that this problem only occur when I create the RAID array with superblocks 1.0, 1.1 and 1.2.
With the superblock 0.90 I don't encounter this issue.Here are the commands to easily reproduce the issue
mdadm -C
/dev/md_d0-e 1.0 -l 1 -n 2 -b internal -R/dev/sda/dev/sdbmdadm/dev/md_d0-f/dev/sda
mdadm/dev/md_d0-r/dev/sda
mdadm/dev/md_d0-a/dev/sda
cat/proc/mdstatThe output of mdstat is:
Personalities : [raid1]md_d0: active raid1 sda[0](F) sdb[1]104849 blocks super 1.2 [2/1] [_U] bitmap: 0/7 pages [0KB], 8KB chunkunused devices: <none>
I'm wondering if the way I'm failing and re-adding a disk is correct. Did I make something wrong?
If I change the superblock to "-e 0.90", there's no problem with this set of commands.
Quoted 8 lines
For now, I found a work-around with superblock 1.0 which consists in zeroing the superblock before re-adding the disk. But I suppose that doing so will force a full rebuild of the re-added disk, and I don't want this, because I'm using write-intent bitmaps.
I'm using mdadm - v2.5.6 on Debian Etch with kernel 2.6.18-4.
Bug or misunderstanding from myself? Any help would be appreciated :)
Thanks
Hubert
The kernel 2.6.20 Changelog says:
- restarting device recovery after a clean shutdown (version-1 metadata only) didn't work as intended (or at all).
That might be my problem, and I confirm 2.6.20.12 is working correctly.
Hubert