exporting service on multiple wan
Hi all,
I've a routing problem. I'm setting up a router based on debian (kernel 2.4).
I need to setup routing to export an ftp service (ftp server is in dmz) to 2 wan (both).
I setup prerouting ad forward rule with no problem.
The problem is that reply packet use default gateway (default wan) even though they are enter using the other wan.
I solved it marking packets in input from the dmz iface and force to use another gateway (iproute2), but in this way I don't export ftp service on default wan.
how I can setup routing to export ftp service on both iface?
Thanks in advance,
Fabio
Signature · 13 lines
Dott. Fabio Marcone
2T srl
Telefono +39 - 0871- 540154
Fax +39 - 0871- 571594
Email fabio.marcone(AT)duet.it
Indirizzo Viale B. Croce 573
66013 Chieti Scalo (CH)
GNU/Linux registered user #400424
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartcQuoted 12 lines · Fabio Marcone
Hi all,
I've a routing problem. I'm setting up a router based on debian (kernel 2.4).I need to setup routing to export an ftp service (ftp server is in dmz) to 2 wan (both).
I setup prerouting ad forward rule with no problem.
The problem is that reply packet use default gateway (default wan) even though they are enter using the other wan.
Quoted 8 lines
I solved it marking packets in input from the dmz iface and force to use another gateway (iproute2), but in this way I don't export ftp service on default wan.
how I can setup routing to export ftp service on both iface?
Thanks in advance,
Fabio
One way to do this:
1. Assign 2 private domain IP addresses to the ftp server and listen to both for ftp. IP1 and IP2
2. Map one IP each for WAN address. WAN1>>IP1 and WAN2>>IP2
3. On the Linux machine, set policy routing based on src IP of reply packet i.e. src IP1 goes thro' WAN1 and src IP2 goes thro' WAN2.
Mohan
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
How about conn-marking the (NEW state)packets in POSTROUTING?
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Mohan Sundaram
Sent: Friday, October 19, 2007 10:19 AM
To: LARTC
Subject: Re: [LARTC] exporting service on multiple wan
Quoted 2 lines · Fabio Marcone
Hi all,
I've a routing problem. I'm setting up a router based on debian
(kernel
Quoted 3 lines
2.4).
I need to setup routing to export an ftp service (ftp server is in
dmz)
Quoted 5 lines
to 2 wan (both).
I setup prerouting ad forward rule with no problem.
The problem is that reply packet use default gateway (default wan)
even
Quoted 3 lines
though they are enter using the other wan.
I solved it marking packets in input from the dmz iface and force to
use
Quoted 7 lines
another gateway (iproute2), but in this way I don't export ftp service on default wan.
how I can setup routing to export ftp service on both iface?
Thanks in advance,
Fabio
One way to do this:
1. Assign 2 private domain IP addresses to the ftp server and listen to both for ftp. IP1 and IP2
2. Map one IP each for WAN address. WAN1>>IP1 and WAN2>>IP2
3. On the Linux machine, set policy routing based on src IP of reply packet i.e. src IP1 goes thro' WAN1 and src IP2 goes thro' WAN2.
Mohan
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 2 lines · Salim S I
How about conn-marking the (NEW state)packets in POSTROUTING?
Would probably need to use conntrack ESTABLISHED,DNAT and ROUTE directive for packets coming from LAN to make sure packet goes out from the same interface it came on.
Mohan
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Sorry, I forgot for a moment it was DMZ.
In mangle PREROUTING
-j CONNMARK restore-mark
-m mark --mark 0x0 -i WAN1 -j CONNMARK --set-mark 0x1 -m mark --mark 0x0 -i WAN2 -j CONNMARK --set-mark 0x2
Two routing tables, one for each mark.
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Mohan Sundaram
Sent: Friday, October 19, 2007 12:09 PM
To: 'LARTC'
Subject: Re: [LARTC] exporting service on multiple wan
Quoted 2 lines · Salim S I
How about conn-marking the (NEW state)packets in POSTROUTING?
Would probably need to use conntrack ESTABLISHED,DNAT and ROUTE directive for packets coming from LAN to make sure packet goes out from the same interface it came on.
Mohan
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc