TNC3
Hi
I'am looking for support to get a TNC3S with 2 modem working With standard kissattach I got modem 1 on the air.
In the ax25 how-to I found:
If you have a dual port tnc and it is connected to your /dev/ttyS0 serial device at 9600 bps,
the command:/usr/sbin/mkiss -s 9600 /dev/ttyS0 /dev/ptyp0 /dev/ptyp1 /usr/sbin/kissattach /dev/ttyp0 port1 /usr/sbin/kissattach /dev/ttyp1 port2
But none of the modem do work
Who has a TNC3S running ?
Peter
PC2A
Hi Peter,
Your info is absolutely right.
However, you should put your TNC into kiss mode manually i.e. using a terminal program to instruct it to change into kiss mode (see the TNC3S manual).
Communicating with the terminal program through serial port with TNC is only possible if AX25 driver is NOT loaded.
Then the order of operation is :
Enter into your terminal program.
Choose the appropriate port and speed.
Reboot your TNC3S in order to make it detect your serial port speed when pressing ENTER key (autobaud routine when TNC powerer up).
Type the commands :
INTFACE TERM and press return
At this point you can monitor incoming traffic on both ports.
INTFACE KISS and press return
RESET and press return
Now your TNC is in kiss mode and you cannot communicate any more via the terminal program. You will only see garbage on the screen.
You can now load the AX25 mkiss driver and continue with AX25 applications.
Note ; since I did not perform these commands for years (I left my TNC2 in KISS mode forever) I may have forgotten the syntax) I do not remember the name of Linux simple serial communication program...
73 de Bernard, f6bvp
Quoted 24 lines · Peter
Hi
I'am looking for support to get a TNC3S with 2 modem working With standard kissattach I got modem 1 on the air.
In the ax25 how-to I found:
If you have a dual port tnc and it is connected to your/dev/ttyS0serial device at 9600 bps,
the command:/usr/sbin/mkiss-s 9600/dev/ttyS0/dev/ptyp0/dev/ptyp1/usr/sbin/kissattach/dev/ttyp0port1/usr/sbin/kissattach/dev/ttyp1port2But none of the modem do work
Who has a TNC3S running ?Peter
PC2A
-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 69 lines · Bernard Pidoux
Hi Peter,
Your info is absolutely right.
However, you should put your TNC into kiss mode manually i.e. using a terminal program to instruct it to change into kiss mode (see the TNC3S manual).
Communicating with the terminal program through serial port with TNC is only possible if AX25 driver is NOT loaded.
Then the order of operation is :
Enter into your terminal program.
Choose the appropriate port and speed.
Reboot your TNC3S in order to make it detect your serial port speed when pressing ENTER key (autobaud routine when TNC powerer up).Type the commands :
INTFACE TERM and press return
At this point you can monitor incoming traffic on both ports.
INTFACE KISS and press return
RESET and press returnNow your TNC is in kiss mode and you cannot communicate any more via the terminal program. You will only see garbage on the screen.
You can now load the AX25 mkiss driver and continue with AX25 applications.
Note ; since I did not perform these commands for years (I left my TNC2 in KISS mode forever) I may have forgotten the syntax) I do not remember the name of Linux simple serial communication program...
73 de Bernard, f6bvp
Quoted 16 lines · Peter
Hi
I'am looking for support to get a TNC3S with 2 modem working With standard kissattach I got modem 1 on the air.
In the ax25 how-to I found:
If you have a dual port tnc and it is connected to your/dev/ttyS0serial device at 9600 bps,
the command:/usr/sbin/mkiss-s 9600/dev/ttyS0/dev/ptyp0/dev/ptyp1/usr/sbin/kissattach/dev/ttyp0port1/usr/sbin/kissattach/dev/ttyp1port2But none of the modem do work
Who has a TNC3S running ?Quoted 8 lines
Peter
PC2A
-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 5 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
minicom is the program :-)
Hi all
The trick is/was to put the TNC in KISS mode.
The TNC3S has serveral programmas that can put into the memory. With the right dipswitch on the back you can startup a programma In my case rskiss. This put the TNC in KISS mode on the rs232 port at boot-up. Thanks for the emails!
Peter
Bernard Pidoux schreef:
Quoted 68 lines
Hi Peter,
Your info is absolutely right.
However, you should put your TNC into kiss mode manually i.e. using a terminal program to instruct it to change into kiss mode (see the TNC3S manual).
Communicating with the terminal program through serial port with TNC is only possible if AX25 driver is NOT loaded.
Then the order of operation is :
Enter into your terminal program.
Choose the appropriate port and speed.
Reboot your TNC3S in order to make it detect your serial port speed when pressing ENTER key (autobaud routine when TNC powerer up).Type the commands :
INTFACE TERM and press return
At this point you can monitor incoming traffic on both ports.
INTFACE KISS and press return
RESET and press returnNow your TNC is in kiss mode and you cannot communicate any more via the terminal program. You will only see garbage on the screen.
You can now load the AX25 mkiss driver and continue with AX25 applications.
Note ; since I did not perform these commands for years (I left my TNC2 in KISS mode forever) I may have forgotten the syntax) I do not remember the name of Linux simple serial communication program...
73 de Bernard, f6bvp
Quoted 16 lines · Peter
Hi
I'am looking for support to get a TNC3S with 2 modem working With standard kissattach I got modem 1 on the air.
In the ax25 how-to I found:
If you have a dual port tnc and it is connected to your/dev/ttyS0serial device at 9600 bps,
the command:/usr/sbin/mkiss-s 9600/dev/ttyS0/dev/ptyp0/dev/ptyp1/usr/sbin/kissattach/dev/ttyp0port1/usr/sbin/kissattach/dev/ttyp1port2But none of the modem do work
Who has a TNC3S running ?Quoted 8 lines
Peter
PC2A
-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 2 lines
Communicating with the terminal program through serial port with TNC is only possible if AX25 driver is NOT loaded.
Adding a basic TIP terminal program as an AX25 driver application is near the top of my wish list. It would be handy many times for getting the attention of a wayward TNC and putting it back into KISS mode.
JNOS has that and it's so useful I've actually set up basic JNOS instances a couple times just to have the TIP functionality.
Anybody out there have the source code to the original TIP program? I need it for another project (N800..) but maybe it wouldn't be hard to hook it to AX25.
Bill - WA7NWP