Skip to contentSkip to conversation

MPC85xx DMA drivers, first testing results.

DISCUSSION Clemens Koller 2 participants 2 messages Dec 6, 2007 – Dec 7, 2007

lore
Share & tools
lore
#0 lore raw

Hi There!

I just tried to use the fsldma on the mpc8540. It seems to work fine here, but I would be glad if somebody can confirm before I move on:

I added the following to my mpc8540ads compatible board's .dts (see my comments, where the not yet available documentation was unclear):

dma@21000 {
        #address-cells = <1>;
        #size-cells = <1>;
        compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
        device-id = <0>;
        reg = <21300 4>;        /* DGSR - DMA general status register */
        /* reg = <21000 4>;*/   /* or use offset of DMA machine ??? */
        ranges = <0 21100 200>; /* we have 4 DMA channels at 21100, size=80 each */
        dma-channel@0 {
                compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
                device-id = <0>; /* or cell-index ??? */
                reg = <0 80>;
                interrupt-parent = <&mpic>;
                interrupts = <14 2>;
        };
        dma-channel@80 {        /* or use 0,1,2,3 instead of 0,80,100,180 ??? */
                compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
                device-id = <1>;
                reg = <80 80>;
                interrupt-parent = <&mpic>;
                interrupts = <15 2>;
        };
        dma-channel@100 {
                compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
                device-id = <2>;
                reg = <100 80>;
                interrupt-parent = <&mpic>;
                interrupts = <16 2>;
        };
        dma-channel@180 {
                compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
                device-id = <3>;
                reg = <180 80>;
                interrupt-parent = <&mpic>;
                interrupts = <17 2>;
        };
};
$ dmesg then says:

of-fsl-dma e0021300.dma: Probe the Freescale DMA driver for fsl,mpc8540-dma controller at 0xe0021300... of-fsl-dma-channel e0021100.dma-channe: selftest: start...
of-fsl-dma-channel e0021100.dma-channe: selftest: finished, err=0.
of-fsl-dma-channel e0021100.dma-channe: #0 (fsl,mpc8540-dma-channel), irq 21 of-fsl-dma-channel e0021180.dma-channe: selftest: start...
of-fsl-dma-channel e0021180.dma-channe: selftest: finished, err=0.
of-fsl-dma-channel e0021180.dma-channe: #1 (fsl,mpc8540-dma-channel), irq 22 of-fsl-dma-channel e0021200.dma-channe: selftest: start...
of-fsl-dma-channel e0021200.dma-channe: selftest: finished, err=0.
of-fsl-dma-channel e0021200.dma-channe: #2 (fsl,mpc8540-dma-channel), irq 23 of-fsl-dma-channel e0021280.dma-channe: selftest: start...
of-fsl-dma-channel e0021280.dma-channe: selftest: finished, err=0.
of-fsl-dma-channel e0021280.dma-channe: #3 (fsl,mpc8540-dma-channel), irq 24

I added another dev_info() to get at least a glue that the selftest is run. It looks like dev_info(fsl_chan->dev, ...); seems to be truncated.

I have no idea if interrupts are working well... the callback isn't used yet.

Otherwise, nice work! :-) I'm looking forward to see this functionality in mainline.

Regards,

Signature · 10 lines
Clemens Koller
__________________________________
R&D Imaging Devices
Anagramm GmbH
Rupert-Mayer-Straße 45/1
Linhof Werksgelände
D-81379 München
Tel.089-741518-50
Fax 089-741518-19
http://www.anagramm-technology.com
#1 lore raw
Quoted 9 lines · Clemens Koller

Hi There!

I just tried to use the fsldma on the mpc8540. It seems to work fine here, but I would be glad if somebody can confirm before I move on:

I added the following to my mpc8540ads compatible board's .dts (see my comments, where the not yet available documentation was unclear):

Quoted 15 lines
dma@21000 {
         #address-cells = <1>;
         #size-cells = <1>;
         compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
         device-id = <0>;
         reg = <21300 4>;        /* DGSR - DMA general status register */
         /* reg = <21000 4>;*/   /* or use offset of DMA machine ??? */
         ranges = <0 21100 200>; /* we have 4 DMA channels at 21100, size=80 each */
         dma-channel@0 {
                 compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
                 device-id = <0>; /* or cell-index ??? */
                 reg = <0 80>;
                 interrupt-parent = <&mpic>;
                 interrupts = <14 2>;
         };

Do this:

                dma@21300 {
                        #address-cells = <1>;
                        #size-cells = <1>;
                        compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
                        cell-index = <0>;
                        reg = <21300 4>; /* DMA general status register */
                        ranges = <0 21100 200>;

                        dma-channel@0 {
                                compatible = "fsl,mpc8540-dma-channel", 
"fsl,eloplus-dma-channel";
                                cell-index = <0>;
                                reg = <0 80>;
                                interrupt-parent = <&mpic>;
                                interrupts = <14 2>;
                        };
Signature · 2 lines
Timur Tabi
Linux Kernel Developer @ Freescale