Port 0x80 I/O speed
Hi everyone.
That was a succesful request, thanks to all who responded. This message also just now went out with all the respondents in CC but I believe that copy isn't making the list, so here's one without...
In total you provided 60 reports which are listed below in increasing order of time spent for an outb to port 0x0. Let's face it, these things are competitions, and Chris has won!
Time varies between 0.54 microseconds and 2.50 microseconds, with most around 1.3/1.4 microseconds. Numbers 58, 59 and 60 (the ones at > 2 us) I dont completely trust since similar machines are among the fastest as well.
Note also that ISA isn't applicable to those 3...
Most machines need no delays anywhere, and those that do would probably be served with a udelay(1) as well but I believe this sampling is showing that a udelay(2) would be the conservative choice.
Thanks again to all those that responded. There's probably a few cut & paste and/or math errors in the below. The jury can not be held accountable for any missed prestige!
Congrats to Chris... ;-)
Cheers,
Rene
1. 0.54 Chris Holvenstot: out 1301, in 1252
AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ (2412 MHz)
2. 0.56 Török Edwin: out 1107, in 1067
AMD Athlon(tm) 64 Processor 3200+, Asus A9N-E (2000 MHz)
3. 0.58 Mike Lampard: out 1342, in 249
AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ (2300 mhZ)
4. 0.69 Jeremy O'Brien: out 411, in 519
Pentium III M 1400Mhz (600Mhz)
5. 0.76 Ville Syrjälä: out 1830, in 1166
Intel(R) Core(TM)2 CPU 6600 (2400MHz)
6. 0.78 Maxim Levitsky: out 1650, in 1065
Core 2 Duo (ICH8/Intel DG965RY motherboard) (2128 MHz)
7. 0.83 Paolo Ornati: out 1498, in 964
Core2 Duo 1.8 GHz (1800 Mhz)
8. 0.88 Ondrej Zary: out 2824, in 1899
Pentium 4 3.2GHz, i925X (3200 MHz)
9. 0.90 Dave Young: out 2522, in 1788
Intel(R) Pentium(R) D CPU 2.80GHz (2800 MHz)
10. 0.90 Randy Dunlap: out 2702, in 1903
Intel(R) Pentium(R) D CPU 3.00GHz (3000 MHz)
11. 1.08 Maxim Levitsky: out 1730, in 1138
Core 2 Duo (ICH8/Intel DG965RY motherboard) (1596 MHz)
12. 1.14 Peter Zijlstra: out 1743, in 1737
AMD Athlon(tm) MP 1800+ (1533 MHz)
13. 1.16 Peter Zijlstra: out 116, in 47
Pentium 133 (100 MHz)
14. 1.17 Ondrej Zary: out 263, in 93
Cyrix MII PR300 (225MHz), i430TX
15. 1.18 [email protected]: out 1295, in 1162
1100 MHz Athlon, nForce2 chipset, nForce2 ISA bridge
16. 1.20 Ville Syrjälä: out 1925, in 1266
Intel(R) Core(TM)2 CPU 6600 (1596 MHz)
17. 1.21 Peter Zijlstra: out 811, in 354
Pentium III (Coppermine) (672 MHz)
18. 1.22 Juergen Beisert: out 1215, in 1094
Intel(R) Celeron(TM) CPU (1000MHz)
19. 1.23 Ondrej Zary: out 163, in 163
Pentium MMX 166MHz @133MHz, VIA VPX (133 Mhz)
20. 1.27 Dave Haywood: out 1183, in 706
Pentium III (Coppermine) 930 MHz
21. 1.28 Ondrej Zary: out 2178, in 1651
Celeron 1.7GHz (P4-based), i845 (1700 MHz)
22. 1.29 Olivér Pintér: out 4062, in 2502
Intel(R) Pentium(R) 4 CPU 3.00GHz (3150 Mhz)
23. 1.30 James Lamanna: out 3902, in 2372
Intel(R) Pentium(R) 4 CPU 3.00GHz
24. 1.31 Ville Syrjälä: out 914, in 406
Pentium III (Coppermine) 700 Mhz
25. 1.32 [email protected]: out 794, in 348
600 MHz PIII (Katmai), 440BX chipset, 82371AB/EB/MB PIIX4:
26. 1.33 Edwin de Caluwé: out 667, in 305
Celeron (Coppermine) 500 MHz
27. 1.34 Ville Syrjälä: out 1142, in 475
Pentium III (Coppermine) 850 MHz
28. 1.35 Ville Syrjälä: out 607, in 272
Pentium II (Deschutes) 450 MHz
29. 1.36 Pádraig Brady: out 4069, in 2507
Intel(R) Pentium(R) 4 CPU 3.00GHz:
30. 1.37 Juergen Beisert: out 684, in 280
Pentium III (Katmai) 500 MHz
31. 1.37 Nigel Cunningham: out 2472, in 2505
AMD 1.8GHz Turion ATI RS480 - Mitac 8350 mobo (1800 MHz)
32. 1.38 Rene Herman: out 553, in 251
PII 400 (Intel 440BX) (400 MHz)
33. 1.40 Guennadi Liakhovetski: out 1263, in 1221
AMD Duron 900MHz
34. 1.41 John Stoffel: out 774, in 332
PIII, Dual 550Mhz Xeon
35. 1.42 Török Edwin: out 2368, in 1783
Intel Core Duo T2300 (Dell Inspiron 6400, ICH7) (1667 MHz)
36. 1.43 Luciano Rocha: out 2711, in 1856
Intel(R) Pentium(R) 4 CPU 1.90GHz
37. 1.43 Ondrej Zary: out 620, in 305
Celeron 433MHz, i440BX
38. 1.44 [email protected]: out 624, in 297
433 MHz Celeron (Mendocino), 440 BX chipset
39. 1.44 Pádraig Brady: out 2588, in 2581
Dual-Core AMD Opteron(tm) Processor 2210 (1800)
40. 1.46 Pádraig Brady: out 2480, in 1666
Intel(R) Pentium(R) M processor 1.70GHz
41. 1.48 Guennadi Liakhovetski: out 1480, in 1409
VIA C7 1GHz
42. 1.51 Pádraig Brady: out 905, in 640
Intel(R) Pentium(R) M processor 1.70GHz (600 Mhz)
43. 1.51 Alejandro Riveira Fernández: out 3025, in 1653
AMD 3800 X2 (2000MHz) ULi M1697
44. 1.52 [email protected]: out 1212, in 388
800 MHz Transmeta Crusoe TM5800, Transmeta/ALi M7101
45. 1.53 Nigel Cunningham: out 1231, in 1208
AMD 1.8GHz Turion ATI RS480 - Mitac 8350 mobo (800 MHz)
46. 1.56 Alejandro Riveira Fernández: out 1566, in 876
AMD 3800 X2 (1000MHz) ULi M1697
47. 1.58 Ondrej Zary: out 3367, in 1959
Xeon 3050 2.13GHz, Dell PE860
48. 1.61 Jiri Slaby: out 3217, in 1898
Intel(R) Xeon(R) CPU E5335 @ 2.00GHz
49. 1.63 Ondrej Zary: out 2114, in 849
Celeron 1.3GHz, i440BX
50. 1.64 Ondrej Zary: out 2631, in 1606
Xeon E5310 1.6GHz, Dell PE1950
51. 1.79 Cyrill Gorcunov: out 1428, in 1450
AMD Turion(tm) 64 Mobile Technology ML-30 (800 MHz)
52. 1.80 Alistair John Strachan: out 2712, in 2606
1.5GHz C7, Via chipset
53. 1.85 Rene Herman: out 2400, in 2400
AMD Duron 1300 (AMD756)
54. 1.92 Danny ter Haar: out 4038, in 1707
Intel(R) Pentium(R) M processor 2.10GHz
55. 1.97 Ville Syrjälä: out 2562, in 2562
AMD Duron(tm) processor 1300
56. 1.98 Danny ter Haar: out 1185, in 537
Intel(R) Pentium(R) M processor 2.10GHz (600 MHz)
57. 1.99 Romano Giannetti: out 3446, in 2652
CoreDuo T2080/1.73GHz
58. 2.17 Jiri Slaby: out 6500, in 3135
Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz
59. 2.23 [email protected]: out 4914, in 4927
2200 MHz Athlon 64, K8T890 chipset, VT8237 ISA bridge:
60. 2.50 Jiri Slaby: out 5508, in 5524
Dual Core AMD Opteron(tm) Processor 275 (2200 MHz)
Quoted 3 lines · Rene Herman
Time varies between 0.54 microseconds and 2.50 microseconds, with most around 1.3/1.4 microseconds. Numbers 58, 59 and 60 (the ones at > 2 us) I dont completely trust since similar machines are among the fastest as well.
Hi.
Just want to say that I get up to 2.7 on my Acer Aspire 5720Z laptop.
cycles: out 3955, in 3679
cycles: out 3972, in 3683
cycles: out 3963, in 3692
cycles: out 3961, in 3663
cycles: out 3977, in 3679
cycles: out 3990, in 3675
The test program was run with the following frequency setup:
# cpufreq-info cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: acpi-cpufreq CPUs which need to switch frequency at the same time: 0 1 hardware limits: 800 MHz - 1.47 GHz available frequency steps: 1.47 GHz, 1.07 GHz, 800 MHz available cpufreq governors: ondemand, userspace, performance current policy: frequency should be within 800 MHz and 1.47 GHz. The governor "performance" may decide which speed to use within this range. current CPU frequency is 1.47 GHz (asserted by call to hardware).
# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Pentium(R) Dual CPU T2310 @ 1.46GHz stepping : 13 cpu MHz : 1467.000 cache size : 1024 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl est tm2 ssse3 cx16 xtpr lahf_lm bogomips : 2930.06 clflush size : 64
This seems to be higher than the #60 on your list. What makes my machine (and a few of the others') special?
Vegard
Quoted 20 lines · Rene Herman
Hi everyone.
That was a succesful request, thanks to all who responded. This message also just now went out with all the respondents in CC but I believe that copy isn't making the list, so here's one without...
In total you provided 60 reports which are listed below in increasing order of time spent for an outb to port
0x0. Let's face it, these things are competitions, and Chris has won!Time varies between 0.54 microseconds and 2.50 microseconds, with most around 1.3/1.4 microseconds. Numbers 58, 59 and 60 (the ones at > 2 us) I dont completely trust since similar machines are among the fastest as well.
Note also that ISA isn't applicable to those 3...
Most machines need no delays anywhere, and those that do would probably be served with a udelay(1) as well but I believe this sampling is showing that a udelay(2) would be the conservative choice.
Quoted 8 lines
Thanks again to all those that responded. There's probably a few cut & paste and/or math errors in the below. The jury can not be held accountable for any missed prestige!
Congrats to Chris... ;-)
Cheers,
Rene
But there are some things that get set up long before udelay() is calibrated! The interrupt controllers, the timer, etc. You can't just substitute or you will end up with machines that won't boot!
grep /usr/src/linux-uname -r/arch/i386/kernel/*.c for lots of outb_p()'s!
That's why the manufacturing port, 0x80, really needs to be used for I/O timing! If it kills that one machine, then that one machine is broken and needs to be fixed. It's probably an undetected error in a FPGA that once reported will get fixed.
In fact, it might just be one motherboard and if that motherboard was replaced, the problem goes away. We have been there before. We can't "fix" stuff that's not broken without running the risk of breaking a lot more stuff.
[Snipped...]
Cheers,
Dick Johnson
Penguin : Linux version 2.6.22.1 on an i686 machine (5588.30 BogoMips). My book : http://www.AbominableFirebug.com/
_
****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.
Thank you.
Quoted 4 lines · linux-os (Dick Johnson)
But there are some things that get set up long before
udelay()is calibrated! The interrupt controllers, the timer, etc. You can't just substitute or you will end up with machines that won't boot!
We understand the problem. But it's not all that bad.
Rene.
Quoted 5 lines · linux-os (Dick Johnson)
But there are some things that get set up long before
udelay()is calibrated! The interrupt controllers, the timer, etc. You can't just substitute or you will end up with machines that won't boot!
The initial value could be set conservatively high.