Base Taco Platform support

index 0256344..be76731 100644
@@ -12,5 +12,6 @@
 
 void ebony_init(void *mac0, void *mac1);
 void bamboo_init(void *mac0, void *mac1);
+void taco_init(void *mac0, void *mac1);
 
 #endif /* _PPC_BOOT_44X_H_ */

index f1928af..ece0c71 100644
@@ -1226,6 +1226,18 @@ static struct cpu_spec __initdata cpu_specs[] = {
 		.machine_check		= machine_check_4xx,
 		.platform		= "ppc440",
 	},
+	{ /* Matches both physical and logical PVR for 440EP (logical pvr = pvr | 0x8) */
+		.pvr_mask		= 0xf0000ff7,
+		.pvr_value		= 0x400008d4,
+		.cpu_name		= "440EP Rev. C",
+		.cpu_features		= CPU_FTRS_44X,
+		.cpu_user_features	= COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+		.icache_bsize		= 32,
+		.dcache_bsize		= 32,
+		.cpu_setup		= __setup_cpu_440ep,
+		.machine_check		= machine_check_4xx,
+		.platform		= "ppc440",
+	},
 	{ /* Use logical PVR for 440EP (logical pvr = pvr | 0x8) */
 		.pvr_mask		= 0xf0000fff,
 		.pvr_value		= 0x400008db,

@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2008 PIKA Technologies
+ *   Sean MacLennan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+				   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+
+	taco_init(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}

@@ -0,0 +1,33 @@
+/*
+ * Copyright (c) 2008 PIKA Technologies
+ *   Sean MacLennan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2 of the License
+ */
+#include "ops.h"
+#include "4xx.h"
+#include "44x.h"
+
+static u8 *taco_mac0, *taco_mac1;
+
+static void taco_fixups(void)
+{
+	unsigned long sysclk = 66000000;
+
+	ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
+	ibm4xx_sdram_fixup_memsize();
+	ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
+	dt_fixup_mac_addresses(taco_mac0, taco_mac1);
+}
+
+void taco_init(void *mac0, void *mac1)
+{
+	platform_ops.fixups = taco_fixups;
+	platform_ops.exit = ibm44x_dbcr_reset;
+	taco_mac0 = mac0;
+	taco_mac1 = mac1;
+	fdt_init(_dtb_start);
+	serial_console_init();
+}

205 lines not on this page · raw message

@@ -0,0 +1,239 @@
+/*
+ * PIKA Warp(tm) board specific routines
+ *
+ * Copyright (c) 2008 PIKA Technologies
+ *   Sean MacLennan <[email protected]>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+#include <linux/init.h>
+#include <linux/of_platform.h>
+#include <linux/kthread.h>
+
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/time.h>
+#include <asm/uic.h>
+
+#include "44x.h"
+
+#define WARP_GPIO_BASE 0xEF600B00ULL
+
+static __initdata struct of_device_id warp_of_bus[] = {
+	{ .compatible = "ibm,plb4", },
+	{ .compatible = "ibm,opb", },
+	{ .compatible = "ibm,ebc", },
+	{},
+};
+
+static int __init warp_device_probe(void)
+{
+	of_platform_bus_probe(NULL, warp_of_bus, NULL);
+
+	return 0;
+}
+machine_device_initcall(warp, warp_device_probe);
+
+static int __init warp_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	if(!of_flat_dt_is_compatible(root, "pika,warp"))
+		return 0;
+
+	return 1;
+}
+
+define_machine(warp) {
+	.name 				= "Warp",
+	.probe 				= warp_probe,
+	.progress 			= udbg_progress,
+	.init_IRQ 			= uic_init_tree,
+	.get_irq 			= uic_get_irq,
+	.restart			= ppc44x_reset_system,
+	.calibrate_decr 	= generic_calibrate_decr,
+};
+
+/* This is for the power LEDs 1 = on, 0 = off, -1 = leave alone */
+void warp_set_power_leds(int green, int red)
+{
+	static void *gpio_base = NULL;
+	unsigned leds;
+
+	if(gpio_base == NULL) {
+		if((gpio_base = ioremap(WARP_GPIO_BASE, 0x148)) == NULL) {
+			printk("ERROR: Unable to remap GPIO base.\n");
+			return;
+		}
+	}
+
+	leds = readl(gpio_base + 0x100);
+
+	switch(green) {
+	case 0: leds &= ~0x80; break;
+	case 1: leds |=  0x80; break;
+	}
+	switch(red) {
+	case 0: leds &= ~0x40; break;
+	case 1: leds |=  0x40; break;
+	}
+
+	writel(leds, gpio_base + 0x100);
+}
+EXPORT_SYMBOL(warp_set_power_leds);
+
+
+static int pika_dtm_thread(void *fpga)
+{
+	extern int ad7414_get_temp(int index);
+
+	while(!kthread_should_stop()) {
+		int temp = ad7414_get_temp(0);
+
+		out_be32(fpga, temp);
+
+		set_current_state(TASK_INTERRUPTIBLE);
+		schedule_timeout(HZ);
+	}
+
+	return 0;
+}
+
+
+static int __devinit warp_fpga_init(void)
+{
+	struct device_node *np;
+	void *fpga;
+	int irq;
+	struct resource res;
+	struct task_struct *dtm_thread;
+
+	if((np = of_find_compatible_node(NULL, NULL, "pika,fpga")) == NULL) {
+		printk(KERN_ERR __FILE__ ": Unable to find fpga\n");
+		return -ENOENT;
+	}
+
+	if((irq = irq_of_parse_and_map(np, 0)) == NO_IRQ) {
+		printk(KERN_ERR __FILE__ ": irq_of_parse_and_map failed\n");
+		return -EBUSY;
+	}
+
+	/* We do not call of_iomap here since it would map in the entire
+	 * fpga space, which is over 8k.
+	 */
+	if(of_address_to_resource(np, 0, &res) ||
+	   (fpga = ioremap(res.start, 0x24)) == NULL) {
+		printk(KERN_ERR __FILE__ ": Unable to map FPGA\n");
+		return -ENOENT;
+	}
+
+	/* Turn off the line LEDs */
+	out_be32(fpga + 8, 0);
+
+	dtm_thread = kthread_run(pika_dtm_thread, fpga + 0x20, "pika-dtm");
+
+	if(IS_ERR(dtm_thread)) {
+		iounmap(fpga);
+		printk(KERN_ERR __FILE__ ": Unable to start PIKA DTM thread\n");
+		return PTR_ERR(dtm_thread);
+	}
+
+	return 0;
+}
+device_initcall(warp_fpga_init);
+
+#define NAND_FLASH
+#ifdef NAND_FLASH
+/* --- All of this code is for the NAND flash */
+
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/ndfc.h>
+
+
+#define CS_NAND_0	1	/* use chip select 1 for NAND device 0 */
+
+#define WARP_NAND_FLASH_REG_ADDR	0xD0000000UL
+#define WARP_NAND_FLASH_REG_SIZE	0x2000
+
+static struct resource warp_ndfc = {
+	.start = WARP_NAND_FLASH_REG_ADDR,
+	.end   = WARP_NAND_FLASH_REG_ADDR + WARP_NAND_FLASH_REG_SIZE,
+	.flags = IORESOURCE_MEM,
+};
+
+static struct mtd_partition nand_parts[] = {
+	{
+		.name = "nand",
+		.offset = 0,
+		.size = MTDPART_SIZ_FULL,
+	}
+};
+
+struct ndfc_controller_settings warp_ndfc_settings = {
+	.ccr_settings = (NDFC_CCR_BS(CS_NAND_0) | NDFC_CCR_ARAC1),
+	.ndfc_erpn = 0,
+};
+
+static struct ndfc_chip_settings warp_chip0_settings = {
+	.bank_settings = 0x80002222,
+};
+
+struct platform_nand_ctrl warp_nand_ctrl = {
+	.priv = &warp_ndfc_settings,
+};
+
+static struct platform_device warp_ndfc_device = {
+	.name = "ndfc-nand",
+	.id = 0,
+	.dev = {
+		.platform_data = &warp_nand_ctrl,
+	},
+	.num_resources = 1,
+	.resource = &warp_ndfc,
+};
+
+static struct nand_ecclayout nand_oob_16 = {
+	.eccbytes = 3,
+	.eccpos = { 0, 1, 2, 3, 6, 7 },
+	.oobfree = { {.offset = 8, .length = 16} }
+};
+
+static struct platform_nand_chip warp_nand_chip0 = {
+	.nr_chips = 1,
+	.chip_offset = CS_NAND_0,
+	.nr_partitions = ARRAY_SIZE(nand_parts),
+	.partitions = nand_parts,
+	.chip_delay = 50,
+	.ecclayout = &nand_oob_16,
+	.priv = &warp_chip0_settings,
+};
+
+static struct platform_device warp_nand_device = {
+	.name = "ndfc-chip",
+	.id = 0,
+	.num_resources = 1,
+	.resource = &warp_ndfc,
+	.dev = {
+		.platform_data = &warp_nand_chip0,
+		.parent = &warp_ndfc_device.dev,
+	}
+};
+
+static int warp_setup_flash(void)
+{
+	platform_device_register(&warp_ndfc_device);
+	platform_device_register(&warp_nand_device);
+
+	return 0;
+}
+device_initcall(warp_setup_flash);
+
+#endif /* NAND_FLASH */

index 0256344..9db0213 100644
@@ -12,5 +12,6 @@
 

index f1928af..ece0c71 100644
@@ -1226,6 +1226,18 @@ static struct cpu_spec __initdata cpu_specs[] = {

@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2008 PIKA Technologies
+ *   Sean MacLennan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+				   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+
+	warp_init(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}

@@ -0,0 +1,33 @@
+/*
+ * Copyright (c) 2008 PIKA Technologies
+ *   Sean MacLennan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2 of the License
+ */
+#include "ops.h"
+#include "4xx.h"
+#include "44x.h"
+
+static u8 *warp_mac0, *warp_mac1;
+
+static void warp_fixups(void)
+{
+	unsigned long sysclk = 66000000;
+
+	ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
+	ibm4xx_sdram_fixup_memsize();
+	ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
+	dt_fixup_mac_addresses(warp_mac0, warp_mac1);
+}
+
+void warp_init(void *mac0, void *mac1)
+{
+	platform_ops.fixups = warp_fixups;
+	platform_ops.exit = ibm44x_dbcr_reset;
+	warp_mac0 = mac0;
+	warp_mac1 = mac1;
+	fdt_init(_dtb_start);
+	serial_console_init();
+}