Skip to contentSkip to conversation

iTCO watchdog timer

DISCUSSION Stephen Clark 4 participants 8 messages Mar 4, 2008 – May 6, 2008 2 messages not in the archive

lore
Share & tools
lore
#0 lore raw

Hello,

I have new Intel DG33FB mainboard.

Mar  2 20:47:19 joker1 kernel: iTCO_vendor_support: vendor-support=0
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Found a ICH9DH TCO device (Version=2, TCOBASE=0x0460)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
...
Mar  4 14:22:59 joker1 kernel: iTCO_wdt: Unexpected close, not stopping watchdog!

I start watchdog.c and then kill it expecting the system to reboot - but it doesn't.

Isn't this how it is supposed to work?

Linux version 2.6.23.15-137.fc8

Thanks,
Steve

Signature · 3 lines
"They that give up essential liberty to obtain temporary safety, deserve neither liberty nor safety."  (Ben Franklin)

"The course of history shows that as a government grows, liberty decreases."  (Thomas Jefferson)
#1 lore raw
Quoted 17 lines · On Tue, 04 Mar 2008 15:10:05 -0500 Stephen Clark <[email protected]>…

Hello,

I have new Intel DG33FB mainboard.

Mar  2 20:47:19 joker1 kernel: iTCO_vendor_support: vendor-support=0
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver 
v1.02 (26-Jul-2007)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Found a ICH9DH TCO device 
(Version=2, TCOBASE=0x0460)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: initialized. heartbeat=30 sec 
(nowayout=0)
...
Mar  4 14:22:59 joker1 kernel: iTCO_wdt: Unexpected close, not stopping 

watchdog!

Quoted 8 lines

I start watchdog.c and then kill it expecting the system to reboot - but it doesn't.

Isn't this how it is supposed to work?

Linux version 2.6.23.15-137.fc8

(cc Wim)

#2 lore raw

Hi All,

Sorry but it's quite busy at the moment...

Quoted 15 lines
Quoted 15 lines

I have new Intel DG33FB mainboard.

Mar  2 20:47:19 joker1 kernel: iTCO_vendor_support: vendor-support=0
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver 
v1.02 (26-Jul-2007)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Found a ICH9DH TCO device 
(Version=2, TCOBASE=0x0460)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: initialized. heartbeat=30 sec 
(nowayout=0)
...
Mar  4 14:22:59 joker1 kernel: iTCO_wdt: Unexpected close, not stopping 

watchdog!

Quoted 4 lines
Quoted 4 lines

I start watchdog.c and then kill it expecting the system to reboot - but it doesn't.

Isn't this how it is supposed to work?

This is indeed how it should work. It's indeed strange that the system doesn't reboot. If I find some time I will give you some test code to run.

Greetings,
Wim.

#3 lore raw
Quoted 18 lines · Wim Van Sebroeck

Hi All,

Sorry but it's quite busy at the moment...

Quoted 13 lines
Quoted 13 lines

I have new Intel DG33FB mainboard.

Mar  2 20:47:19 joker1 kernel: iTCO_vendor_support: vendor-support=0
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Found a ICH9DH TCO device (Version=2, TCOBASE=0x0460)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
...
Mar  4 14:22:59 joker1 kernel: iTCO_wdt: Unexpected close, not stopping watchdog!

I start watchdog.c and then kill it expecting the system to reboot - but it doesn't.

Quoted 11 lines
Quoted 2 lines
Quoted 2 lines

Isn't this how it is supposed to work?

This is indeed how it should work. It's indeed strange that the system doesn't reboot. If I find some time I will give you some test code to run.

Greetings,
Wim.

That would be much appreciated. One of the reasons I bought this mother board was the WDT.

Steve

Signature · 3 lines
"They that give up essential liberty to obtain temporary safety, deserve neither liberty nor safety."  (Ben Franklin)

"The course of history shows that as a government grows, liberty decreases."  (Thomas Jefferson)
#4 lore raw
In reply to Wim Van Sebroeck
Quoted 17 lines · Wim Van Sebroeck

Hi All,

Sorry but it's quite busy at the moment...

Quoted 13 lines
Quoted 13 lines

I have new Intel DG33FB mainboard.

Mar  2 20:47:19 joker1 kernel: iTCO_vendor_support: vendor-support=0
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: Found a ICH9DH TCO device (Version=2, TCOBASE=0x0460)
Mar  2 20:47:19 joker1 kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
...
Mar  4 14:22:59 joker1 kernel: iTCO_wdt: Unexpected close, not stopping watchdog!

I start watchdog.c and then kill it expecting the system to reboot - but it doesn't.

Quoted 9 lines
Quoted 1 line
Quoted 1 line

Isn't this how it is supposed to work?

This is indeed how it should work. It's indeed strange that the system doesn't reboot. If I find some time I will give you some test code to run.

Greetings,
Wim.

Hi Wim,

Just wondered if you had any more thoughts or if you have any test you would like me to run.

Regards,
Steve

Signature · 5 lines
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety."  (Ben Franklin)

"The course of history shows that as a government grows, liberty
decreases."  (Thomas Jefferson)
#5 lore raw

Hi Steve,

Quoted 2 lines

Just wondered if you had any more thoughts or if you have any test you would like me to run.

Didn't had any time yet. Could you run the following watchdog test-program first and sent me the output? Just compile it with: gcc -o watchdog watchdog.c and then run the watchdog program.

Thanks,
Wim.

#include <stdio.h>
#include <unistd.h>
#include <fcntl.h>
#include "linux/ioctl.h"

struct watchdog_info {
unsigned long options; /* Options the card/driver supports */
unsigned long firmware_version; /* Firmware version of the card */
unsigned char identity[32]; /* Identity of the board */
};

#define WATCHDOG_IOCTL_BASE 'W'

#define WDIOC_GETSUPPORT _IOR(WATCHDOG_IOCTL_BASE, 0, struct watchdog_info)
#define WDIOC_GETSTATUS _IOR(WATCHDOG_IOCTL_BASE, 1, int)
#define WDIOC_GETBOOTSTATUS _IOR(WATCHDOG_IOCTL_BASE, 2, int)
#define WDIOC_GETTEMP _IOR(WATCHDOG_IOCTL_BASE, 3, int)
#define WDIOC_SETOPTIONS _IOR(WATCHDOG_IOCTL_BASE, 4, int)
#define WDIOC_KEEPALIVE _IOR(WATCHDOG_IOCTL_BASE, 5, int)
#define WDIOC_SETTIMEOUT _IOWR(WATCHDOG_IOCTL_BASE, 6, int)
#define WDIOC_GETTIMEOUT _IOR(WATCHDOG_IOCTL_BASE, 7, int)
#define WDIOC_GETTIMELEFT _IOR(WATCHDOG_IOCTL_BASE, 10, int)

#define WDIOS_DISABLECARD 0x0001 /* Turn off the watchdog timer */
#define WDIOS_ENABLECARD 0x0002 /* Turn on the watchdog timer */

int main(int argc, const char *argv[]) {
	int i = 5;
	int c;
	int temperature;
	int timeout = 34;
	int timervalue;
	int flags;
	int options;
	int ret;
	struct watchdog_info wdinfo;
	int fd=open("/dev/watchdog",O_WRONLY);
	if (fd==-1) {
		perror("watchdog");
		return 1;
	}
	ret = ioctl(fd, WDIOC_GETSUPPORT, &wdinfo);
	printf("The GETSUPPORT call reported (%d):\n", ret);
	if (ret) {
		printf("  options         : ?\n");
		printf("  firmware_version: ?\n");
		printf("  identity        : ?\n");
	} else {
		printf("  options         : 0x%04x\n", wdinfo.options);
		printf("  firmware_version: %d\n", wdinfo.firmware_version);
		printf("  identity        : %s\n", wdinfo.identity);
	}
	ret = ioctl(fd, WDIOC_GETSTATUS, &flags);
	if (ret) flags=0;
	printf("The GETSTATUS call reported %x (%d)\n", flags, ret);
	ret = ioctl(fd, WDIOC_GETBOOTSTATUS, &flags);
	if (ret) flags=0;
	printf("The GETBOOTSTATUS call reported %x (%d)\n", flags, ret);

	ret = ioctl(fd, WDIOC_GETTEMP, &temperature);
	if (ret) temperature=0;
	printf("The GETTEMP call reported %d°F = %d°C (ret=%d)\n", temperature, ((temperature - 32) * 5 / 9), ret);

	options = WDIOS_DISABLECARD;
	ret = ioctl(fd, WDIOC_SETOPTIONS, &options);
	if (ret) options=0;
	printf("The SETOPTIONS (DISABLECARD) call returned=%d\n", ret);
	options = WDIOS_ENABLECARD;
	ret = ioctl(fd, WDIOC_SETOPTIONS, &options);
	if (ret) options=0;
	printf("The SETOPTIONS (ENABLECARD) call returned=%d\n", ret);

	ret = ioctl(fd, WDIOC_GETTIMEOUT, &flags);
	if (ret) flags=0;
	printf("The timeout is %d seconds (%d)\n", flags, ret);
	ret = ioctl(fd, WDIOC_SETTIMEOUT, &timeout);
	if (ret) timeout=0;
	printf("The timeout is now set to %d seconds (%d)\n", timeout, ret);
	ret = ioctl(fd, WDIOC_GETTIMEOUT, &flags);
	if (ret) flags=0;
	printf("The timeout is %d seconds (%d)\n", flags, ret);
	ret = ioctl(fd, WDIOC_GETTIMELEFT, &timervalue);
	if (ret) timervalue=0;
	printf("The GETTIMELEFT call reported %d seconds (0x%04x) (%d)\n", timervalue ,timervalue,ret);
	while(i--) {
		ioctl(fd, WDIOC_KEEPALIVE, 0);
		sleep(10 + i);
		ret = ioctl(fd, WDIOC_GETTIMELEFT, &timervalue);
		if (ret) timervalue=0;
		printf("The GETTIMELEFT call reported %d seconds (0x%04x) (%d)\n", timervalue,timervalue,ret);
	}
	write(fd, "V", 1);
	fsync(fd);
	close(fd);

	return 0;
}
#6 lore raw
Quoted 11 lines · Wim Van Sebroeck

Hi Steve,

Quoted 1 line

Just wondered if you had any more thoughts or if you have any test you would like me to run.

Didn't had any time yet. Could you run the following watchdog test-program first and sent me the output? Just compile it with: gcc -o watchdog watchdog.c and then run the watchdog program.

Thanks,
Wim.

[root@joker20 ~]# ./testwdog
The GETSUPPORT call reported (-1):
options : ?
firmware_version: ?
identity : ?
The GETSTATUS call reported 0 (0)
The GETBOOTSTATUS call reported 0 (0)
The GETTEMP call reported 0°F = -17°C (ret=-1) The SETOPTIONS (DISABLECARD) call returned=0 The SETOPTIONS (ENABLECARD) call returned=0 The timeout is 30 seconds (0)
The timeout is now set to 34 seconds (0)
The timeout is 34 seconds (0)
The GETTIMELEFT call reported 33 seconds (0x0021) (0) The GETTIMELEFT call reported 19 seconds (0x0013) (0) The GETTIMELEFT call reported 20 seconds (0x0014) (0) The GETTIMELEFT call reported 21 seconds (0x0015) (0) The GETTIMELEFT call reported 22 seconds (0x0016) (0) The GETTIMELEFT call reported 22 seconds (0x0016) (0)

[root@joker20 ~]# lspci -vvv
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02)
Subsystem: Intel Corporation Unknown device 5044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=512K]
        Region 1: I/O ports at 3430 [size=8]
        Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
        Region 3: Memory at e0300000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- 

Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.0 Communication controller: Intel Corporation 82G33/G31/P35/P31 Express MEI Controller (rev 02)
Subsystem: Intel Corporation Unknown device 5044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e04a6100 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-

                Address: 0000000000000000  Data: 0000

00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network Connection (rev 02)
Subsystem: Intel Corporation Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at e0480000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at e04a4000 (32-bit, non-prefetchable) [size=4K] Region 2: I/O ports at 3400 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 00000000fee0f00c Data: 41b9
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: e1000e
Kernel modules: e1000e

00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin A routed to IRQ 18
Region 4: I/O ports at 30e0 [size=32]
Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 30c0 [size=32]
Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin C routed to IRQ 17
Region 4: I/O ports at 30a0 [size=32]
Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin C routed to IRQ 17
Region 0: Memory at e04a5c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?> Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02)
Subsystem: Intel Corporation Unknown device 0002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e04a0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated
Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown,
Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 

00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-

                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, 

Latency L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surpise+

                        Slot #  1, PowerLimit 10.000000; Interlock- 

NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown,
Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: Intel Corporation Optiplex 755
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: e0200000-e02fffff
        Prefetchable memory behind bridge: 

00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-

                LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, 

Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surpise+

                        Slot #  2, PowerLimit 10.000000; Interlock- 

NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown,
Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: fee0f00c Data: 4171
Capabilities: [90] Subsystem: Intel Corporation 82801I (ICH9
Family) PCI Express Port 2
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 

00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-

                LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, 

Latency L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surpise+

                        Slot #  3, PowerLimit 10.000000; Interlock- 

NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown,
Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: fee0f00c Data: 4179
Capabilities: [90] Subsystem: Intel Corporation 82801I (ICH9
Family) PCI Express Port 3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 00001000-00001fff
        Memory behind bridge: e0100000-e01fffff
        Prefetchable memory behind bridge: 

00000000e0500000-00000000e05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-

                LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, 

Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surpise+

                        Slot #  4, PowerLimit 10.000000; Interlock- 

NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown,
Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: fee0f00c Data: 4181
Capabilities: [90] Subsystem: Intel Corporation 82801I (ICH9
Family) PCI Express Port 4
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 

00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-

                LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, 

Latency L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surpise+

                        Slot #  5, PowerLimit 10.000000; Interlock- 

NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown,
Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: fee0f00c Data: 4189
Capabilities: [90] Subsystem: Intel Corporation 82801I (ICH9
Family) PCI Express Port 5
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 3080 [size=32]
Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3060 [size=32]
Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3040 [size=32]
Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at e04a5800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?> Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: e0000000-e00fffff
        Prefetchable memory behind bridge: 

00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort+ <SERR- <PERR-

BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Intel Corporation Unknown device 5044

00:1f.0 ISA bridge: Intel Corporation 82801IH (ICH9DH) LPC Interface Controller (rev 02)
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0
Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt

00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin A routed to IRQ 2298
        Region 0: I/O ports at 3428 [size=8]
        Region 1: I/O ports at 343c [size=4]
        Region 2: I/O ports at 3420 [size=8]
        Region 3: I/O ports at 3438 [size=4]
        Region 4: I/O ports at 3020 [size=32]
        Region 5: Memory at e04a5000 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- 

Queue=0/4 Enable+
Address: fee0a00c Data: 41a1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] Vendor Specific Information <?> Kernel driver in use: ahci
Kernel modules: ahci

00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
Subsystem: Intel Corporation Unknown device 5044
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Interrupt: pin B routed to IRQ 18
Region 0: Memory at e04a6000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

02:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6101 single-port PATA133 interface (rev b2) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Marvell Technology Group Ltd. 88SE6101 single-port
PATA133 interface
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at 2018 [size=8]
        Region 1: I/O ports at 2024 [size=4]
        Region 2: I/O ports at 2010 [size=8]
        Region 3: I/O ports at 2020 [size=4]
        Region 4: I/O ports at 2000 [size=16]
        Region 5: Memory at e0200000 (32-bit, non-prefetchable) [size=512]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA 

PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+
AuxPwr- TransPend-

                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, 

Latency L0 <256ns, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: pata_marvell
Kernel modules: pata_acpi, ata_generic, pata_marvell

04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 20)
Subsystem: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit
Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 2297
Region 0: Memory at e0100000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 1000 [size=256]
Expansion ROM at e0500000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data <?>
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+
Queue=0/1 Enable+
Address: 00000000fee0400c Data: 41a9
Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+
AuxPwr+ TransPend+

                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, 

Latency L0 <256ns, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: sky2
Kernel modules: sky2

06:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Unknown device 5044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium

Quoted 1 line

TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e0004000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci

Signature · 5 lines
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety."  (Ben Franklin)

"The course of history shows that as a government grows, liberty
decreases."  (Thomas Jefferson)

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

#9 lore raw
Quoted 30 lines · Stephen Clark
Quoted 22 lines · Wim Van Sebroeck

Hi Steve,

Quoted 11 lines

[root@joker20 ~]# ./testwdog
The GETSUPPORT call reported (-1):
options : ?
firmware_version: ?
identity : ?
The GETSTATUS call reported 0 (0)
The GETBOOTSTATUS call reported 0 (0)
The GETTEMP call reported 0°F = -17°C (ret=-1) The SETOPTIONS (DISABLECARD) call returned=0 The SETOPTIONS (ENABLECARD) call returned=0 The timeout is 30 seconds (0)

Quoted 8 lines

The timeout is now set to 34 seconds (0)
The timeout is 34 seconds (0)
The GETTIMELEFT call reported 33 seconds (0x0021) (0) The GETTIMELEFT call reported 19 seconds (0x0013) (0) The GETTIMELEFT call reported 20 seconds (0x0014) (0) The GETTIMELEFT call reported 21 seconds (0x0015) (0) The GETTIMELEFT call reported 22 seconds (0x0016) (0) The GETTIMELEFT call reported 22 seconds (0x0016) (0)

Quoted 7 lines

So the timer counts down. So I have to find out why it doesn't reboot. And it has to do only with the ICH9 chipsets. I'll adapt the iTCO_wdt driver so that we have extra debugging info and will sent it to you.

Greetings,
Wim.

Quoted 7 lines

Thanks,

I'll be waiting patiently.

Regards,
Steve

Hi Wim,

Still waiting.

Regards,
Steve

Signature · 5 lines
"They that give up essential liberty to obtain temporary safety,
deserve neither liberty nor safety."  (Ben Franklin)

"The course of history shows that as a government grows, liberty
decreases."  (Thomas Jefferson)