mvsas: fill in error info record and phy mode6 bits.

and remove some unused members from struct.

---
drivers/scsi/mvsas.c | 123
+++++++++++++++++++++++++++++++++++---------------

1 files changed, 87 insertions(+), 36 deletions(-)

index 5ec0665..3a447fe 100644
@@ -37,11 +37,13 @@

#include <linux/dma-mapping.h>
#include <linux/ctype.h>
#include <scsi/libsas.h>
+#include <scsi/scsi_tcq.h>
+#include <scsi/sas_ata.h>
#include <asm/io.h>

#define DRV_NAME "mvsas"
-#define DRV_VERSION "0.5.1"
-#define _MV_DUMP 0
+#define DRV_VERSION "0.5.2"
+#define _MV_DUMP 0
#define MVS_DISABLE_NVRAM
#define MVS_DISABLE_MSI

@@ -52,7 +54,7 @@

    readl(regs + MVS_##reg);        \
    } while (0)

-#define MVS_ID_NOT_MAPPED 0xff
+#define MVS_ID_NOT_MAPPED 0x7f
#define MVS_CHIP_SLOT_SZ (1U << mvi->chip->slot_width)

/* offset for D2H FIS in the Received FIS List Structure */ @@ -84,6 +86,7 @@ enum driver_configuration {
MVS_RX_FIS_COUNT = 17, /* Optional rx'd FISs (max 17) */

MVS_QUEUE_SIZE = 30, /* Support Queue depth */
+ MVS_CAN_QUEUE = MVS_SLOTS - 1, /* SCSI Queue depth */
};

/* unchangeable hardware details */
@@ -358,7 +361,20 @@ enum hw_register_bits {

    /* VSR */
    /* PHYMODE 6 (CDB) */
-    PHY_MODE6_DTL_SPEED    = (1U << 27),
+    PHY_MODE6_LATECLK    = (1U << 29),    /* Lock Clock */
+    PHY_MODE6_DTL_SPEED    = (1U << 27),    /* Digital Loop Speed */
+    PHY_MODE6_FC_ORDER    = (1U << 26),    /* Fibre Channel Mode Order*/
+    PHY_MODE6_MUCNT_EN    = (1U << 24),    /* u Count Enable */
+    PHY_MODE6_SEL_MUCNT_LEN    = (1U << 22),    /* Training Length
Select */
+    PHY_MODE6_SELMUPI    = (1U << 20),    /* Phase Multi Select (init) */
+    PHY_MODE6_SELMUPF    = (1U << 18),    /* Phase Multi Select (final) */
+    PHY_MODE6_SELMUFF    = (1U << 16),    /* Freq Loop Multi Sel(final) */
+    PHY_MODE6_SELMUFI    = (1U << 14),    /* Freq Loop Multi Sel(init) */
+    PHY_MODE6_FREEZE_LOOP    = (1U << 12),    /* Freeze Rx CDR Loop */
+    PHY_MODE6_INT_RXFOFFS    = (1U << 3),    /* Rx CDR Freq Loop Enable */
+    PHY_MODE6_FRC_RXFOFFS    = (1U << 2),    /* Initial Rx CDR Offset */
+    PHY_MODE6_STAU_0D8    = (1U << 1),    /* Rx CDR Freq Loop Saturate */
+    PHY_MODE6_RXSAT_DIS    = (1U << 0),    /* Saturate Ctl */

};

enum mvs_info_flags {
@@ -511,7 +527,43 @@ enum status_buffer {
};

enum error_info_rec {

-    CMD_ISS_STPD    =  (1U << 31),    /* Cmd Issue Stopped */
+    CMD_ISS_STPD    = (1U << 31),    /* Cmd Issue Stopped */
+    CMD_PI_ERR    = (1U << 30),    /* Protection info error.  see flags2 */
+    RSP_OVER    = (1U << 29),    /* rsp buffer overflow */
+    RETRY_LIM    = (1U << 28),    /* FIS/frame retry limit exceeded */
+    UNK_FIS     = (1U << 27),    /* unknown FIS */
+    DMA_TERM    = (1U << 26),    /* DMA terminate primitive rx'd */
+    SYNC_ERR    = (1U << 25),    /* SYNC rx'd during frame xmit */
+    TFILE_ERR    = (1U << 24),    /* SATA taskfile Error bit set */
+    R_ERR        = (1U << 23),    /* SATA returned R_ERR prim */
+    RD_OFS        = (1U << 20),    /* Read DATA frame invalid offset */
+    XFER_RDY_OFS    = (1U << 19),    /* XFER_RDY offset error */
+    UNEXP_XFER_RDY    = (1U << 18),    /* unexpected XFER_RDY error */
+    DATA_OVER_UNDER = (1U << 16),    /* data overflow/underflow */
+    INTERLOCK    = (1U << 15),    /* interlock error */
+    NAK        = (1U << 14),    /* NAK rx'd */
+    ACK_NAK_TO    = (1U << 13),    /* ACK/NAK timeout */
+    CXN_CLOSED    = (1U << 12),    /* cxn closed w/out ack/nak */
+    OPEN_TO     = (1U << 11),    /* I_T nexus lost, open cxn timeout */
+    PATH_BLOCKED    = (1U << 10),    /* I_T nexus lost, pathway blocked */
+    NO_DEST     = (1U << 9),    /* I_T nexus lost, no destination */
+    STP_RES_BSY    = (1U << 8),    /* STP resources busy */
+    BREAK        = (1U << 7),    /* break received */
+    BAD_DEST    = (1U << 6),    /* bad destination */
+    BAD_PROTO    = (1U << 5),    /* protocol not supported */
+    BAD_RATE    = (1U << 4),    /* cxn rate not supported */
+    WRONG_DEST    = (1U << 3),    /* wrong destination error */
+    CREDIT_TO    = (1U << 2),    /* credit timeout */
+    WDOG_TO     = (1U << 1),    /* watchdog timeout */
+    BUF_PAR     = (1U << 0),    /* buffer parity error */
+};
+
+enum error_info_rec_2 {
+    SLOT_BSY_ERR    = (1U << 31),    /* Slot Busy Error */
+    GRD_CHK_ERR    = (1U << 14),    /* Guard Check Error */
+    APP_CHK_ERR    = (1U << 13),    /* Application Check error */
+    REF_CHK_ERR    = (1U << 12),    /* Reference Check Error */
+    USR_BLK_NM    = (1U << 0),    /* User Block Number */

};

struct mvs_chip_info {

@@ -543,28 +595,12 @@ struct mvs_cmd_hdr {
    __le32            reserved[4];
};

-struct mvs_slot_info {

-    struct sas_task        *task;
-    u32            n_elem;
-    u32            tx;

-
- /* DMA buffer for storing cmd tbl, open addr frame, status buffer,
- * and PRD table
- */
- void *buf;
- dma_addr_t buf_dma;
-#if _MV_DUMP
- u32 cmd_size;
-#endif
-
- void *response;
-};
-

struct mvs_port {
    struct asd_sas_port    sas_port;
    u8            port_attached;
    u8            taskfileset;
    u8            wide_port_phymap;

+ struct list_head list;
};

struct mvs_phy {

@@ -582,6 +618,27 @@ struct mvs_phy {
    u32        frame_rcvd_size;
    u8        frame_rcvd[32];
    u8        phy_attached;
+    enum sas_linkrate    minimum_linkrate;
+    enum sas_linkrate    maximum_linkrate;
+};
+
+struct mvs_slot_info {
+    struct list_head    list;
+    struct sas_task        *task;
+    u32            n_elem;
+    u32            tx;

+
+ /* DMA buffer for storing cmd tbl, open addr frame, status buffer,
+ * and PRD table
+ */
+ void *buf;
+ dma_addr_t buf_dma;
+#if _MV_DUMP
+ u32 cmd_size;
+#endif
+
+ void *response;
+ struct mvs_port *port;
};

struct mvs_info {
@@ -612,21 +669,14 @@ struct mvs_info {

    const struct mvs_chip_info *chip;

- unsigned long tags[MVS_SLOTS];

+    u8            tags[MVS_SLOTS];
    struct mvs_slot_info    slot_info[MVS_SLOTS];
                /* further per-slot information */
    struct mvs_phy        phy[MVS_MAX_PHYS];
    struct mvs_port        port[MVS_MAX_PHYS];
-
-    u32            can_queue;    /* per adapter */
-    u32            tag_out;    /*Get*/
-    u32            tag_in;        /*Give*/

-};
-
-struct mvs_queue_task {
- struct list_head list;
-
- void *uldd_task;
+#ifdef MVS_USE_TASKLET
+ struct tasklet_struct tasklet;
+#endif
};

static int mvs_phy_control(struct asd_sas_phy *sas_phy, enum phy_func func, @@ -641,10 +691,11 @@ static u32 mvs_read_port_irq_mask(struct mvs_info *mvi, u32 port);
static u32 mvs_is_phy_ready(struct mvs_info *mvi, int i); static void mvs_detect_porttype(struct mvs_info *mvi, int i); static void mvs_update_phyinfo(struct mvs_info *mvi, int i, int get_st); +static void mvs_release_task(struct mvs_info *mvi, int phy_no);

static int mvs_scan_finished(struct Scsi_Host *, unsigned long); static void mvs_scan_start(struct Scsi_Host *); -static int mvs_sas_slave_alloc(struct scsi_device *scsi_dev); +static int mvs_slave_configure(struct scsi_device *sdev);

static struct scsi_transport_template *mvs_stt;

@@ -659,7 +710,7 @@ static struct scsi_host_template mvs_sht = {
.name = DRV_NAME,
.queuecommand = sas_queuecommand,
.target_alloc = sas_target_alloc,

-    .slave_configure    = sas_slave_configure,
+    .slave_configure    = mvs_slave_configure,

.slave_destroy = sas_slave_destroy,
.scan_finished = mvs_scan_finished,
.scan_start = mvs_scan_start,
@@ -674,7 +725,7 @@ static struct scsi_host_template mvs_sht = {
.use_clustering = ENABLE_CLUSTERING,
.eh_device_reset_handler = sas_eh_device_reset_handler,
.eh_bus_reset_handler = sas_eh_bus_reset_handler,

-    .slave_alloc        = mvs_sas_slave_alloc,
+    .slave_alloc        = sas_slave_alloc,

.target_destroy = sas_target_destroy,
.ioctl = sas_ioctl,
};

1.5.4

This patch (and the following ones) look great. I'm afraid I can't apply them, though ... it looks like your mail tool has stripped some leading spaces:

If you need to add the patches as an attachment to get them through your mailer undamaged, that's fine ... the tools we have will cope with that.

Thanks,

James

Hello James:
I resended mvsas patch set to community. Thank you for your help. I am moving my email client from Outlook to Thunderbird. So sometimes I need to try some configuration. I have already past mvsas driver testing. By far, look well. If you have any suggestions to help me, pls let me know.

Best regards.
Ke

Thanks ... although we have contributors whose use of outlook is mandated by their companies ... although they tend to have to attach patches instead of inlining them.

Thunderbird apparently can be a bit of a problem. There's a section about configuring it in the kernel documentation:

Documentation/email-clients.txt

Will do ... let me review the patches first (got a long flight coming up).

Thanks,

James

BTW the Windows version of Evolution has seen some success, too...

Jeff