2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap)partitions on a SATA drive]
Looks like this earlier message didn't get through. Sid.
-------- Original Message --------
Subject: Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap)partitions on a SATA drive
Date: Mon, 21 Apr 2008 12:55:04 +0100
From: Sid Boyce <[email protected]>
Reply-To: [email protected]
Organization: blueyonder.co.uk
To: [email protected]
Quoted 17 lines · Eric Sandeen
Quoted 7 lines · Sid Boyce
2.6.25
x86_64boots fine as does -git1/2 boxes using reiserfs and ext3. With xfs it can't find these and drops into a shell./dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2swap swap defaults 0 0/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1/ xfs defaults 1 1Quoted 8 lines
From my .config
CONFIG_XFS_FS=mCONFIG_XFS_QUOTA=yCONFIG_XFS_POSIX_ACL=yCONFIG_XFS_RT=yThe other boxes are configure pretty much the same, but I can diff the .config's if required.
Quoted 6 lines
Does it not find the device, or does it not find the filesystem? What's the relevant message? Does it enumerate the partitions it finds, and is your partition in the list? Do you see the xfs module initialization message go by before the error to indicate that it really did get loaded?
-Eric
It doesn't find the device either with 2.6.25-git1 or 2.6.25-git2. I've tried a new kernel with xfs compiled in rather than as a module. The odd thing is that other boxes with ext3, jfs and reiserfs are fine, 2 of them with SATA drives are working with 2.6.25-git2.
The BIOS settings (it's the latest BIOS), but it's OK on 2.6.25, just a problem from 2.6.25-git1.
Primary IDE Master [Optiarc DVD RW A]
SATA 1 [WDC WD5000AAKS-0]
SATA2 to SATA6 [None]
(Onboard Device Configuration)
Silicon SATAII Controller [SATA Mode]
Here goes the messages on boot for 2.6.25-git2.
-----------------------------------------------
scsi0 : sata_sil24
scsi1 : sata_sil24
ata1: SATA max UDMA/100 host n128@0xfdef8000 port 0xfdef8000 irq 16
ata2: SATA max UDMA/100 host n128@0xfdeff000 port 0xfdefa000 irq 16
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)sata_nv 0000:00:0d.0 using SUNCQ mode
scsi2: sata_nv
--- ditto to scsi16 ----
FATAL: Module xfs not found ### I have it built-in this time ### BIOS EDD facility v0.16 2004-Jun-25, 6 devices found Creating device nodes with udev
<<< USB STUFF NOT INCLUDED >>>>
Trying normal resume from /dev/sda2
resume device /dev/sda2 not found (ignoring)
Trying manual resume from /dev/sda2
resume device /dev/sda2 not found (ignoring)
Waiting for device /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 to appear could not find /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 Want me to fall back to /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1? (Y/n) y Waiting for device /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 to appear not found -- exiting to /bin/sh
$
-----------------------------------
There is no /dev/disk directory, /sys/block/ is empty
From 2.6.25 dmesg
==================
scsi0 : sata_sil24
scsi1 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfdeff000 port 0xfdef8000 irq 16
ata2: SATA max UDMA/100 host m128@0xfdeff000 port 0xfdefa000 irq 16
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input2
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)sata_nv 0000:00:0d.0: version 3.5
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xe000 irq 23
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xe008 irq 23
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133 ata3.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 0/32) ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
usbcore: registered new device driver usb
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
Regards
Sid.
Signature · 11 lines
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Specialist, Cricket Coach Microsoft Windows Free Zone - Linux used for all Computing Tasks -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Specialist, Cricket Coach Microsoft Windows Free Zone - Linux used for all Computing Tasks
Hello,
Has someone found the cause of this? I can't boot latest git as of today. I use ext3 if it's relevant. /dev/disk/by-id/ only shows my dvd-burner which is on pata. v2.6.25 is fine on this laptop.
regards, Richard