broken changes @ MPC83xx

Kim,

after being back from holiday and pulling the lates u-boot today (v1.3.3) my MPC8343 based board (mvBL-M7) doesn't work any longer. Not a single character is put out on serial - yet build is not complaining about anything and System.map looks quite normal.

Any ideas what commit can cause this ?

Am I missing any #defines introduced lately ?

regards,
Andre

MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner

-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users

Hi Andre,

I had a similar problem a while back.

Adding the new define:

#define CONFIG_HIGH_BATS 1 /* High BATs supported */

To my config solved the problem.

/Tor

Quoted 29 lines · Andre Schwarz

Kim,

after being back from holiday and pulling the lates u-boot today (v1.3.3) my MPC8343 based board (mvBL-M7) doesn't work any longer. Not a single character is put out on serial - yet build is not complaining about anything and System.map looks quite normal.

Any ideas what commit can cause this ?

Am I missing any #defines introduced lately ?

regards,
Andre

MATRIX VISION GmbH, Talstra??e 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch??ftsf??hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner

-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users

On Mon, 23 Jun 2008 13:25:34 +0200
Andre Schwarz <[email protected]> wrote:

Hello Andre,

include/configs/MVBLM7.h line 30

Quoted 10 lines

include/configs/MVBLM7.h +1 -1

index 349ca14..8c0e8b6 100644
@@ -27,7 +27,7 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define MV_VERSION  "v1.0.1"
+#define MV_VERSION  "v1.0.2"

instead of incrementing this for each patch, can we just use U_BOOT_VERSION instead?

include/configs/MVBLM7.h line 229

Quoted 11 lines

include/configs/MVBLM7.h +2 -0

 #define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR          b6:b4:45:eb:fb:c0
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_FEC1_PHY_NORXERR
 #define CFG_TSEC1_OFFSET	0x24000

@@ -224,6 +225,7 @@
 #define TSEC1_FLAGS		(TSEC_GIGABIT|TSEC_REDUCED)
 
 #define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR         b6:b4:45:eb:fb:c2
 #define CONFIG_TSEC2_NAME  	"TSEC1"

I had removed this from your original board port because this goes against recommended practice; see:

http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/41178

include/configs/MVBLM7.h line 230

Quoted 1 line

include/configs/MVBLM7.h +1 -0

+#define CONFIG_HIGH_BATS       1

this line applied.

Kim