Skip to contentSkip to conversation

MPC83xx ipic problem

DISCUSSION André Schwarz 3 participants 5 messages Jun 30, 2008 – Jul 1, 2008

lore
Share & tools
lore
#0 lore raw

Scott,

actually I'm having trouble with my PCI interrupts. We are running 2.6.26-rc6 on a MPC8343 based board.

There are two external PCI devices connected (FPGA + miniPCI socket). The FPGA is working fine and uses IRQ0 for its PCI_INTA line.

As soon there's a miniPCI module present and the driver loaded (actually=20 an ath5k WiFi module) the system complains after a while :

irq 48: nobody cared
handlers: .... location of the FPGA irq handler
Disabling IRQ #48

-> This is weird since the FPGA isn't working at all and IRQ0 is *not*=20 asserted !

Of course the miniPCI irq is routed to a different pin on the CPU=20 (IRQ1). Having a look at the irq count it's obvious that the WiFi irqs=20 are handled (ath module). The FPGA irq handler is located in the=20 "mvbcdma0" module which is running rock solid without miniPCI present !

mvBL-M7> cat /proc/interrupts
CPU0

16:       1826   IPIC   Level     i2c-mpc
17:          9   IPIC   Level     i2c-mpc
18:        201   IPIC   Level     ath
19:       2896   IPIC   Level     serial
21:          0   IPIC   Level     mpc83xx_spi
32:          2   IPIC   Level     enet_tx
33:        257   IPIC   Level     enet_rx
34:          0   IPIC   Level     enet_error
48:     100000   IPIC   Level     mvbcdma0

BAD: 0

The irq mapping insides the dts :

interrupt-map =3D <0x5800 0 0 1 &ipic 0x30 0x8 -> FPGA @ IRQ0

                 0x6000 0 0 1 &ipic 0x11 0x8      -> miniPCI INTA @ IRQ1
                 0x6000 0 0 2 &ipic 0x11 0x8>;    -> miniPCI INTB @ IRQ1

Is it legal to use a single irq pin twice ?
After all the ath5k doesn't use/assert the INTB line at all ...

If I do all the above after removing the FPGA module and releasing irq48=20 the system doesn't complain anymore ... but hangs after a while with the=20 IRQ1 line being unserviced.

What do you think ?
Any hints ?

Am I doing anything obviously wrong ?

regards,
Andr=E9

MATRIX VISION GmbH, Talstra=DFe 16, DE-71570 Oppenweiler - Registergeric=
ht: Amtsgericht Stuttgart, HRB 271090
Gesch=E4ftsf=FChrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner

#1 lore raw
Quoted 7 lines

interrupt-map = <0x5800 0 0 1 &ipic 0x30 0x8 -> FPGA @ IRQ0

                 0x6000 0 0 1 &ipic 0x11 0x8      -> miniPCI INTA @ 
IRQ1
                 0x6000 0 0 2 &ipic 0x11 0x8>;    -> miniPCI INTB @ 

IRQ1

Is it legal to use a single irq pin twice ?

The device tree simply describes the hardware; if the hardware connects both INTXs to the same IPIC interrupt pin, then it is correct. You'll have to ask a hardware designer whether it is okay to just tie the two lines together; I believe it is, for PCI, but you better ask someone who really knows :-)

Segher

#2 lore raw

Segher,

actually I'm the hardware designer ... :-) .... having trouble with=20 software.

The outputs are open-drain and can be connected (wired-or) together. Otherwise "shared irq" wouldn't be possible that easy.

cheers,
Andr=E9

Quoted 2 lines · Segher Boessenkool
Quoted 2 lines

interrupt-map =3D <0x5800 0 0 1 &ipic 0x30 0x8 -> FPGA @ IRQ0

                 0x6000 0 0 1 &ipic 0x11 0x8      -> miniPCI INTA @ IR=

Q1

Quoted 1 line
Quoted 1 line
                 0x6000 0 0 2 &ipic 0x11 0x8>;    -> miniPCI INTB @ IR=

Q1

Quoted 12 lines
Quoted 2 lines

Is it legal to use a single irq pin twice ?

The device tree simply describes the hardware; if the hardware connects both INTXs to the same IPIC interrupt pin, then it is correct. You'll have to ask a hardware designer whether it is okay to just tie the two lines together; I believe it is, for PCI, but you better ask someone who really knows :-)

Segher

MATRIX VISION GmbH, Talstra=DFe 16, DE-71570 Oppenweiler - Registergeric=
ht: Amtsgericht Stuttgart, HRB 271090
Gesch=E4ftsf=FChrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner

#3 lore raw
In reply to André Schwarz
Quoted 11 lines · André Schwarz

There are two external PCI devices connected (FPGA + miniPCI socket). The FPGA is working fine and uses IRQ0 for its PCI_INTA line.

As soon there's a miniPCI module present and the driver loaded (actually an ath5k WiFi module) the system complains after a while :

irq 48: nobody cared
handlers: .... location of the FPGA irq handler
Disabling IRQ #48

-> This is weird since the FPGA isn't working at all and IRQ0 is *not* asserted !

Are you *sure* that IRQ0 isn't asserted? The IPIC seems to think it is.

Quoted 1 line

Of course the miniPCI irq is routed to a different pin on the CPU (IRQ1).

Perhaps the board wiring is incorrect?

Quoted 5 lines
interrupt-map = <0x5800 0 0 1 &ipic 0x30 0x8      -> FPGA @ IRQ0
                 0x6000 0 0 1 &ipic 0x11 0x8      -> miniPCI INTA @ IRQ1
                 0x6000 0 0 2 &ipic 0x11 0x8>;    -> miniPCI INTB @ IRQ1

Is it legal to use a single irq pin twice ?

Yes.

-Scott

#4 lore raw

Scott,

thanks for your reply.

Honestly I don't think the board wiring is incorrect. FPGA goes to IRQ0 and miniPCI is wired to IRQ1.

Maybe there's a crosstalk problem since the pull-up resistors are=20 packaged inside an array ... I'll check this.

regards,
Andr=C3=A9

Quoted 4 lines · Scott Wood
Quoted 3 lines · Andr=C3=A9 Schwarz wrote:

There are two external PCI devices connected (FPGA + miniPCI socket). The FPGA is working fine and uses IRQ0 for its PCI_INTA line.

Quoted 8 lines
Quoted 8 lines

As soon there's a miniPCI module present and the driver loaded=20 (actually an ath5k WiFi module) the system complains after a while :

irq 48: nobody cared
handlers: .... location of the FPGA irq handler
Disabling IRQ #48

-> This is weird since the FPGA isn't working at all and IRQ0 is *not*=

=20

Quoted 3 lines
Quoted 1 line

asserted !

=20
Are you *sure* that IRQ0 isn't asserted? The IPIC seems to think it is=

.

Quoted 2 lines

=20

Quoted 1 line

Of course the miniPCI irq is routed to a different pin on the CPU (IRQ=

1).

Quoted 5 lines

=20
Perhaps the board wiring is incorrect?
=20

Quoted 2 lines

interrupt-map =3D <0x5800 0 0 1 &ipic 0x30 0x8 -> FPGA @ IRQ0

                 0x6000 0 0 1 &ipic 0x11 0x8      -> miniPCI INTA @ IR=

Q1

Quoted 1 line
Quoted 1 line
                 0x6000 0 0 2 &ipic 0x11 0x8>;    -> miniPCI INTB @ IR=

Q1

Quoted 11 lines
Quoted 2 lines

Is it legal to use a single irq pin twice ?

=20
Yes.
=20
-Scott
=20
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev

MATRIX VISION GmbH, Talstra=DFe 16, DE-71570 Oppenweiler - Registergeric=
ht: Amtsgericht Stuttgart, HRB 271090
Gesch=E4ftsf=FChrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner