e1000 problem @ current u-boot
Wolfgang,
as far as I can see on the list you sent the latest patches for the e1000 driver.
My e1000 (82541ER) stopped working on a MPC5200 based board with latest u-boot.
I have a similar problem on another board ...
Is your e1000 working properly on the latest u-boot ? Do I need any additional defines or environment settings to get it working again ?
Obviously it is - again :-[ - my fault or is related to my build system.
Any help is welcome.
regards,
Andre
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner
Quoted 4 lines · Andre Schwarz
Wolfgang,
as far as I can see on the list you sent the latest patches for the e1000 driver.
My patches just added some device ids,
Quoted 5 lines
My e1000 (82541ER) stopped working on a MPC5200 based board with latest u-boot.
I have a similar problem on another board ...Is your e1000 working properly on the latest u-boot ?
Yes, on a MPC8548 board. I have not tested it on the MPC5200.
Quoted 4 lines
Do I need any additional defines or environment settings to get it working again ?
Obviously it is - again :-[ - my fault or is related to my build system.
I think there are some known problems with PCI on boards with a MPC5200 Rev. A processor, e.g. my EEPRO100 card does not work on it. What exactly does not work?
Wolfgang.
Wolfgang,
of course I meant no offense - of course your patch is harmless.
The System (network camera) is running for nearly 2 years now. Last working version has been u-boot 1.2.x with a 2.6.19 kernel.
Since we've moved to the latest kernel we need a more recent u-boot.
This is what I did - and e1000 no longer works.
Of course I diff'ed the network stuff - no obvious changes at all. So I wonder if the problem is elsewhere and if e1000 is still working in general.
As you say this is obviously true - thanks.
regards,
Andre
Quoted 20 lines · Wolfgang Grandegger
Quoted 4 lines · Andre Schwarz
Wolfgang,
as far as I can see on the list you sent the latest patches for the e1000 driver.
My patches just added some device ids,
Quoted 5 lines
My e1000 (82541ER) stopped working on a MPC5200 based board with latest u-boot.
I have a similar problem on another board ...Is your e1000 working properly on the latest u-boot ?
Yes, on a MPC8548 board. I have not tested it on the MPC5200.
Quoted 3 lines
Do I need any additional defines or environment settings to get it working again ?
Quoted 7 lines
Quoted 1 line
Obviously it is - again :-[ - my fault or is related to my build system.
I think there are some known problems with PCI on boards with a MPC5200 Rev. A processor, e.g. my EEPRO100 card does not work on it. What exactly does not work?
Wolfgang.
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner
Quoted 3 lines · Andre Schwarz
Wolfgang,
of course I meant no offense - of course your patch is harmless.
No problem.
Quoted 10 lines
The System (network camera) is running for nearly 2 years now. Last working version has been u-boot 1.2.x with a 2.6.19 kernel.
Since we've moved to the latest kernel we need a more recent u-boot.
This is what I did - and e1000 no longer works.
Of course I diff'ed the network stuff - no obvious changes at all. So I wonder if the problem is elsewhere and if e1000 is still working in general.
Have you read my previous mail? See below.
Quoted 16 lines
Quoted 15 lines · Wolfgang Grandegger
Quoted 4 lines · Andre Schwarz
Wolfgang,
as far as I can see on the list you sent the latest patches for the e1000 driver.
My patches just added some device ids,
Quoted 5 lines
My e1000 (82541ER) stopped working on a MPC5200 based board with latest u-boot.
I have a similar problem on another board ...Is your e1000 working properly on the latest u-boot ?
Yes, on a MPC8548 board. I have not tested it on the MPC5200.
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines
Do I need any additional defines or environment settings to get it working again ?
Obviously it is - again :-[ - my fault or is related to my build system.
I think there are some known problems with PCI on boards with a MPC5200 Rev. A processor, e.g. my EEPRO100 card does not work on it. What exactly does not work?
More information could be useful.
Wolfgang.
Today I've stressed my diff a quite a bit and tried several config options from other boards that I did _not_ have ...
After adding the config option for skipping the pci host bridge it worked again.
Unfortunately I have no clue why since this can hardly cause that ... maybe I'll dig a little deeper.
cheers,
Andr?
Quoted 42 lines · Wolfgang Grandegger
Quoted 3 lines · Andre Schwarz
Wolfgang,
of course I meant no offense - of course your patch is harmless.
No problem.
Quoted 10 lines
The System (network camera) is running for nearly 2 years now. Last working version has been u-boot 1.2.x with a 2.6.19 kernel.
Since we've moved to the latest kernel we need a more recent u-boot.
This is what I did - and e1000 no longer works.
Of course I diff'ed the network stuff - no obvious changes at all. So I wonder if the problem is elsewhere and if e1000 is still working in general.
Have you read my previous mail? See below.
Quoted 22 lines
Quoted 21 lines · Wolfgang Grandegger
Quoted 4 lines · Andre Schwarz
Wolfgang,
as far as I can see on the list you sent the latest patches for the e1000 driver.
My patches just added some device ids,
Quoted 6 lines
My e1000 (82541ER) stopped working on a MPC5200 based board with latest
u-boot.
I have a similar problem on another board ...Is your e1000 working properly on the latest u-boot ?
Yes, on a MPC8548 board. I have not tested it on the MPC5200.
Quoted 5 lines
Do I need any additional defines or environment settings to get it working again ?
Obviously it is - again :-[ - my fault or is related to my build system.
Quoted 8 lines
Quoted 3 lines
Quoted 3 lines
I think there are some known problems with PCI on boards with a MPC5200 Rev. A processor, e.g. my EEPRO100 card does not work on it. What exactly does not work?
More information could be useful.
Wolfgang.
MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler - Registergericht: Amtsgericht Stuttgart, HRB 271090 Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner