omap ldp board(3430) failed to read/write NAND flash device after booting from nfs

DISCUSSION Zou Tao 2 participants 2 messages Aug 5, 2008

Share & tools

Zou Tao

author

2008-08-05 15:12 UTC #0 lore raw

Hi:
I have booted the omap ldp board with nfs. I want to bootup from flash. so I want to test if linux kernel could read/write flash device. I used
make omap_ldp_defconfig
make uImage
to build kernel.
After kernel booting, I can't read/write flash device. Anyone has bootup the ldp board with Flash device?

Quoted 15 lines

Quoted 6 lines
<6>console [ttyS2] enabled
Linux version 2.6.26-rc8-omap1 (ztao@ZouTao) (gcc version 4.2.3 (Sourcery G++ Lite 2008q1-126)) #2 Thu Jul 31 16:50:54 CST 2008
CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=00c5387f
Machine: OMAP LDP board
Memory policy: ECC disabled, Data cache writeback
Quoted 9 lines
OMAP3430 ES2.2
SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
CPU0: D VIPT write-through cache
CPU0: cache: 768 bytes, associativity 1, 8 byte lines, 64 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages:
32512
Kernel command line: mem=128M console=ttyS2,115200n8 noinitrd root=/dev/nfs rw

Quoted 60 lines

nfsroot=128.247.77.91:/home/ztao/tftproot/arm-linux,nolock,tcp,rsize=4096,wsize=4096
Quoted 57 lines
ip=128.247.77.90
Clocking rate (Crystal/DPLL/ARM core): 26.0/266/500 MHz GPMC revision 5.0
IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
omap2-nand driver initializing
<6>NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
<5>Creating 6 MTD partitions on "omap2-nand.0":
Creating 6 MTD partitions on "omap2-nand.0":
<5>0x00000000-0x00080000 : "X-Loader-NAND" 0x00000000-0x00080000 : "X-Loader-NAND" <5>0x00080000-0x00100000 : "U-Boot-NAND" 0x00080000-0x00100000 : "U-Boot-NAND" <5>0x00100000-0x00140000 : "Boot Env-NAND" 0x00100000-0x00140000 : "Boot Env-NAND" <5>0x00140000-0x00540000 : "Kernel-NAND" 0x00140000-0x00540000 : "Kernel-NAND" <5>0x00540000-0x00940000 : "root file system- NAND" 0x00540000-0x00940000 : "root file system- NAND" <5>0x00940000-0x10000000 : "File System - NAND" 0x00940000-0x10000000 : "File System - NAND"
<5>usbmon: debugfs is not available
/ # dd if=/dev/mtblock4 of=test2 count=1
<3>end_request: I/O error, dev mtdblock4, sector 0
end_request: I/O error, dev mtdblock4, sector 0
<3>Buffer I/O error on device mtdblock4, logical block 0 Buffer I/O error on device mtdblock4, logical block 0 <3>end_request: I/O error, dev mtdblock4, sector 16
end_request: I/O error, dev mtdblock4, sector 16
<3>Buffer I/O error on device mtdblock4, logical block 2 Buffer I/O error on device mtdblock4, logical block 2 <3>end_request: I/O error, dev mtdblock4, sector 24
end_request: I/O error, dev mtdblock4, sector 24
<3>Buffer I/O error on device mtdblock4, logical block 3 Buffer I/O error on device mtdblock4, logical block 3 <3>end_request: I/O error, dev mtdblock4, sector 0
end_request: I/O error, dev mtdblock4, sector 0
<3>Buffer I/O error on device mtdblock4, logical block 0 Buffer I/O error on device mtdblock4, logical block 0
dd: /dev/mtdblock4: Input/output error
/ # / # dd if=ext2.img of=/dev/mtdblock5 count=4 <4>mtdblock: erase of region [0x0, 0x20000] on "File System - NAND" failed
mtdblock: erase of region [0x0, 0x20000] on "File System - NAND" failed 4+0 records in
4+0 records out
/ #

I checked the schematic, the Flash type is PC28F640P30T85, it should be Intel flash. I'm not sure if the config file using wrong flash driver.

Any suggestion will be appreciated.

Best Regards

Tao

Abraham Arce

2008-08-05 15:31 UTC #1 lore raw

Tao,

Quoted 2 lines

I have booted the omap ldp board with nfs. I want to bootup from flash. so I want to test if linux kernel could read/write flash device.

before booting, execute a 'nand unlock' in u-boot

Quoted 1 line

Quoted 1 line
Quoted 1 line
/ # dd if=/dev/mtblock4 of=test2 count=1

# dd if=/dev/mtdblock4 of=test2  count=1
1+0 records in
1+0 records out

Quoted 1 line

Quoted 1 line
Quoted 1 line
/ # / # dd if=ext2.img of=/dev/mtdblock5 count=4

# dd if=rd-ext2.bin of=/dev/mtdblock5 count=4
4+0 records in
4+0 records out
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00080000 00020000 "X-Loader-NAND"
mtd1: 00080000 00020000 "U-Boot-NAND"
mtd2: 00040000 00020000 "Boot Env-NAND"
mtd3: 00400000 00020000 "Kernel-NAND"
mtd4: 0fac0000 00020000 "File System - NAND"
# dd if=rd-ext2.bin of=/dev/mtdblock4 count=4
4+0 records in
4+0 records out

Best Regards
Abraham