Skip to contentSkip to conversation

Burning U-boot on 460EX using BDI3000

U-Boot Felix Radensky 3 participants 4 messages Sep 1, 2008 – Sep 2, 2008

lore
Share & tools
lore
#0 lore raw

Hi,

Can U-boot be burned on 460EX based board (using BDI3000) without configuring DDR controller ? The BDI configuration file for Canyonlands board on Denx site
http://www.denx.de/wiki/view/DULG/Appendix#Section_13.1.
has no DDR setup, but also doesn't work on Canyonlands (fails on flash erase). The configuration file from AMCC site does work, but it contains full DDR setup.

Thanks a lot.

Felix.

#1 lore raw

Hi Felix,

Quoted 7 lines

Can U-boot be burned on 460EX based board (using BDI3000) without configuring DDR controller? The BDI configuration file for Canyonlands board on Denx site
http://www.denx.de/wiki/view/DULG/Appendix#Section_13.1.
has no DDR setup, but also doesn't work on Canyonlands (fails on flash erase). The configuration file from AMCC site does work, but it contains full DDR setup.

It should be possible.

A BDI2000 configuration file flash section looks
something like this:

; ================================================================= [FLASH]

CHIPTYPE    MIRRORX16   ;Flash type: Spansion S29GL256N 32MB
CHIPSIZE    0x2000000   ;The size of one flash chip in bytes
BUSWIDTH    16          ;The width of the flash memory bus in bits
                         ; (8 | 16 | 32 | 64)
;WORKSPACE   0x1000      ;workspace in DDR RAM
FILE        u-boot-1.3.1.bin
FORMAT      BIN 0xfe000000
ERASE       0xfe000000  ;erase sector 0 (128kB sectors)
ERASE       0xfe020000  ;erase sector 1

Make sure to comment out WORKSPACE, and the BDI should be able to program the board flash without needing DDR configured.

Cheers,
Dave

#2 lore raw
In reply to Felix Radensky

Hi Felix,

Here is my BDI configuration file for Canyonlands.

This one should work for you. This one configures OCM instead DDR.

-Victor Gallardo

-----Original Message-----
From: [email protected] [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Felix Radensky
Sent: Monday, September 01, 2008 9:43 AM
To: U-Boot
Subject: [U-Boot] Burning U-boot on 460EX using BDI3000

Hi,

Can U-boot be burned on 460EX based board (using BDI3000) without configuring DDR controller ? The BDI configuration file for Canyonlands board on Denx site
http://www.denx.de/wiki/view/DULG/Appendix#Section_13.1.
has no DDR setup, but also doesn't work on Canyonlands (fails on flash erase). The configuration file from AMCC site does work, but it contains full DDR setup.

Thanks a lot.

Felix.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
-------------- next part --------------
A non-text attachment was scrubbed...
Name: amcc_evb460ex.cfg
Type: application/octet-stream
Size: 3808 bytes
Desc: amcc_evb460ex.cfg
Url : http://lists.denx.de/pipermail/u-boot/attachments/20080901/23902056/attachment.obj

#3 lore raw

Hi, Victor

Quoted 10 lines · Victor Gallardo

Hi Felix,

Here is my BDI configuration file for Canyonlands.

This one should work for you. This one configures OCM instead DDR.

-Victor Gallardo

Your configuration works fine, thanks a lot.

Felix.

Quoted 25 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Felix Radensky
Sent: Monday, September 01, 2008 9:43 AM
To: U-Boot
Subject: [U-Boot] Burning U-boot on 460EX using BDI3000

Hi,

Can U-boot be burned on 460EX based board (using BDI3000) without configuring DDR controller ? The BDI configuration file for Canyonlands board on Denx site
http://www.denx.de/wiki/view/DULG/Appendix#Section_13.1.
has no DDR setup, but also doesn't work on Canyonlands (fails on flash erase). The configuration file from AMCC site does work, but it contains full DDR setup.

Thanks a lot.

Felix.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot