Skip to contentSkip to conversation

PCA9665 support added to i2c-algo-pca and i2c-pca-isa.c

PATCH Marco Aurelio da Costa 2 participants 13 messages Sep 19, 2008 – Jan 14, 2009 12 messages not in the archive I2C subsystem host drivers

lore
Share & tools
lore

Marco Aurelio da Costa

author
#0 lore raw

Hi Wolfram,

Here is the patch against 2.6.26.5.
Please tell me if I did something very wrong ;)

Regards,

Marco

drivers/i2c/algos/i2c-algo-pca.c +128 -12
diff -ur linux-2.6.26.5/drivers/i2c/algos/i2c-algo-pca.c linux-2.6.26.5-new/drivers/i2c/algos/i2c-algo-pca.c
@@ -43,6 +43,14 @@
 #define pca_wait(adap) adap->wait_for_completion(adap->data)
 #define pca_reset(adap) adap->reset_chip(adap->data)
 
+static void pca9665_reset(void *pd)
+{
+	struct i2c_algo_pca_data *adap = pd;
+	pca_outw(adap,I2C_PCA_INDPTR,I2C_PCA_IPRESET);
+	pca_outw(adap,I2C_PCA_IND,0xA5);
+	pca_outw(adap,I2C_PCA_IND,0x5A);
+}
+
 /*
  * Generate a start condition on the i2c bus.
  *

@@ -332,24 +340,132 @@
 
 static int pca_init(struct i2c_adapter *adap)
 {
-	static int freqs[] = {330,288,217,146,88,59,44,36};
-	int clock;
 	struct i2c_algo_pca_data *pca_data = adap->algo_data;
 
-	if (pca_data->i2c_clock > 7) {
-		printk(KERN_WARNING "%s: Invalid I2C clock speed selected. Trying default.\n",
-			adap->name);
-		pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+	adap->algo = &pca_algo;
+	
+	if (pca_data->i2c_chip_type != I2C_PCA_CHIP_9564 && pca_data->i2c_chip_type != I2C_PCA_CHIP_9665 ) {
+		printk(KERN_WARNING "%s: Invalid chip selected. Assuming PCA9564.\n",
+					 adap->name);
+		pca_data->i2c_chip_type = I2C_PCA_CHIP_9564;
 	}
 
-	adap->algo = &pca_algo;
+	if (pca_data->i2c_chip_type == I2C_PCA_CHIP_9564) {
+		static int freqs[] = {330,288,217,146,88,59,44,36};
+		int clock;
+	
+		if (pca_data->i2c_clock > 7) {
+			switch (pca_data->i2c_clock) {
+				case 330000:
+					pca_data->i2c_clock = I2C_PCA_CON_330kHz;
+					break;
+				case 288000:
+					pca_data->i2c_clock = I2C_PCA_CON_288kHz;
+					break;
+				case 217000:
+					pca_data->i2c_clock = I2C_PCA_CON_217kHz;
+					break;
+				case 146000:
+					pca_data->i2c_clock = I2C_PCA_CON_146kHz;
+					break;
+				case 88000:
+					pca_data->i2c_clock = I2C_PCA_CON_88kHz;
+					break;
+				case 59000:
+					pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+					break;
+				case 44000:
+					pca_data->i2c_clock = I2C_PCA_CON_44kHz;
+					break;
+				case 36000:
+					pca_data->i2c_clock = I2C_PCA_CON_36kHz;
+					break;
+				default:
+			printk(KERN_WARNING "%s: Invalid I2C clock speed selected. Trying default.\n",
+				adap->name);
+			pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+			}
+		} else {
+			printk(KERN_WARNING "%s: Choosing the clock frequency based on index is deprecated. Use the nominal frequency.\n",
+						 adap->name);
+		}
+	
+		pca_reset(pca_data);
+	
+		clock = pca_clock(pca_data);
+		DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);
+	
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+	} else {
+		int clock;
+		int mode;
+		int tlow, thigh;
+		int minTLow, minTHi;
+		int tRaiseFall;
+	
+		struct i2c_algo_pca_data *pca_data = adap->algo_data;
+		
+		/* Ignore the reset function from the module, we can use the parallel bus reset */
+		pca_data->reset_chip = pca9665_reset;
+
+		if (pca_data->i2c_clock > 1265800) {
+			printk(KERN_WARNING "%s: I2C clock speed too high. Using 1265.8kHz.\n",
+						 adap->name);
+			pca_data->i2c_clock = 1265800;
+		}
+	
+		if (pca_data->i2c_clock < 60300) {
+			printk(KERN_WARNING "%s: I2C clock speed too low. Using 60.3kHz.\n",
+						 adap->name);
+			pca_data->i2c_clock = 60300;
+		}
+	
+		clock = pca_clock(pca_data)/100; /* Hz*100 */
+	
+
+		if (pca_data->i2c_clock > 10000) {
+			mode = I2C_PCA_MODE_TURBO;
+			minTLow = 14;
+			minTHi  = 5;
+			tRaiseFall = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 4000) {
+			mode = I2C_PCA_MODE_FASTP;
+			minTLow = 17;
+			minTHi  = 9;
+			tRaiseFall = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 1000) {
+			mode = I2C_PCA_MODE_FAST;
+			minTLow = 44;
+			minTHi  = 20;
+			tRaiseFall = 58; /* Raise 29e-8s, Fall 29e-8s */
+		} else {
+			mode = I2C_PCA_MODE_STD;
+			minTLow = 157;
+			minTHi  = 134;
+			tRaiseFall = 127; /* Raise 29e-8s, Fall 98e-8s */
+		}
 
-	pca_reset(pca_data);
+		if (clock < 648) {
+			tlow = 255;
+			thigh = (1000000 - clock*tRaiseFall)/(3*clock)-tlow;
+		} else {
+			tlow = ((1000000 - clock*tRaiseFall)*minTLow)/(3*clock*(minTHi+minTLow));
+			thigh = tlow*minTHi/minTLow;
+		}
+
+		pca_reset(pca_data);
 
-	clock = pca_clock(pca_data);
-	DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);
+		DEB1(KERN_INFO "%s: Clock frequency is %dHz\n", adap->name, clock*100);
 
-	pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+		pca_outw(pca_data,I2C_PCA_INDPTR,I2C_PCA_IMODE);
+		pca_outw(pca_data,I2C_PCA_IND,mode);
+		pca_outw(pca_data,I2C_PCA_INDPTR,I2C_PCA_ISCLL);
+		pca_outw(pca_data,I2C_PCA_IND,tlow);
+		pca_outw(pca_data,I2C_PCA_INDPTR,I2C_PCA_ISCLH);
+		pca_outw(pca_data,I2C_PCA_IND,thigh);
+	
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO);
+	}
 	udelay(500); /* 500 us for oscilator to stabilise */
 
 	return 0;

@@ -384,7 +500,7 @@
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>, "
 	"Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-Bus PCA9564 algorithm");
+MODULE_DESCRIPTION("I2C-Bus PCA9564/PCA9665 algorithm");
 MODULE_LICENSE("GPL");
 
 module_param(i2c_debug, int, 0);
drivers/i2c/busses/i2c-pca-isa.c +9 -3
diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-isa.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-isa.c
@@ -42,6 +42,7 @@
 /* Data sheet recommends 59kHz for 100kHz operation due to variation
  * in the actual clock rate */
 static int clock  = I2C_PCA_CON_59kHz;
+static int chip   = I2C_PCA_CHIP_9564;
 
 static wait_queue_head_t pca_wait;
 

@@ -103,7 +104,7 @@
 	.owner          = THIS_MODULE,
 	.id		= I2C_HW_A_ISA,
 	.algo_data	= &pca_isa_data,
-	.name		= "PCA9564 ISA Adapter",
+	.name		= "PCA9564/PCA9665 ISA Adapter",
 	.timeout	= 100,
 };
 

@@ -132,6 +133,7 @@
 		}
 	}
 
+	pca_isa_data.i2c_chip_type = chip;
 	pca_isa_data.i2c_clock = clock;
 	if (i2c_pca_add_bus(&pca_isa_ops) < 0) {
 		dev_err(dev, "Failed to add i2c bus\n");

@@ -182,7 +184,7 @@
 }
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>");
-MODULE_DESCRIPTION("ISA base PCA9564 driver");
+MODULE_DESCRIPTION("ISA base PCA9564/PCA9665 driver");
 MODULE_LICENSE("GPL");
 
 module_param(base, ulong, 0);

@@ -191,7 +193,11 @@
 module_param(irq, int, 0);
 MODULE_PARM_DESC(irq, "IRQ");
 module_param(clock, int, 0);
-MODULE_PARM_DESC(clock, "Clock rate as described in table 1 of PCA9564 datasheet");
+MODULE_PARM_DESC(clock, "Clock rate in hertz.\n\t\tFor PCA9564: 330000,288000,217000,146000,88000,59000,44000,36000\n"
+		"\t\tFor PCA9665:\tStandard: 60300 - 100099\n\t\t\t\tFast: 100100 - 400099\n\t\t\t\tFast+: 400100 - 10000099\n"
+		"\t\t\t\tTurbo: Up to 1265800");
+module_param(chip, int, 0);
+MODULE_PARM_DESC(chip, "Chip type: 0 = PCA9564; 1 - PCA9665");
 
 module_init(pca_isa_init);
 module_exit(pca_isa_exit);
drivers/i2c/busses/i2c-pca-platform.c +3 -3
diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-platform.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-platform.c
@@ -172,7 +172,7 @@
 
 	i2c->adap.nr = pdev->id >= 0 ? pdev->id : 0;
 	i2c->adap.owner = THIS_MODULE;
-	snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564 at 0x%08lx",
+	snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564/PCA9665 at 0x%08lx",
 		(unsigned long) res->start);
 	i2c->adap.algo_data = &i2c->algo_data;
 	i2c->adap.dev.parent = &pdev->dev;

@@ -246,7 +246,7 @@
 e_alloc:
 	release_mem_region(res->start, res_len(res));
 e_print:
-	printk(KERN_ERR "Registering PCA9564 FAILED! (%d)\n", ret);
+	printk(KERN_ERR "Registering PCA9564/PCA9665 FAILED! (%d)\n", ret);
 	return ret;
 }
 

@@ -290,7 +290,7 @@
 }
 
 MODULE_AUTHOR("Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-PCA9564 platform driver");
+MODULE_DESCRIPTION("I2C-PCA9564/PCA9665 platform driver");
 MODULE_LICENSE("GPL");
 
 module_init(i2c_pca_pf_init);
drivers/i2c/busses/Kconfig +2 -2
diff -ur linux-2.6.26.5/drivers/i2c/busses/Kconfig linux-2.6.26.5-new/drivers/i2c/busses/Kconfig
@@ -630,7 +630,7 @@
 	  will be called i2c-voodoo3.
 
 config I2C_PCA_ISA
-	tristate "PCA9564 on an ISA bus"
+	tristate "PCA9564/PCA9665 on an ISA bus"
 	depends on ISA
 	select I2C_ALGOPCA
 	default n

@@ -647,7 +647,7 @@
 	  time).  If unsure, say N.
 
 config I2C_PCA_PLATFORM
-	tristate "PCA9564 as platform device"
+	tristate "PCA9564/PCA9665 as platform device"
 	select I2C_ALGOPCA
 	default n
 	help
include/linux/i2c-algo-pca.h +29 -2
diff -ur linux-2.6.26.5/include/linux/i2c-algo-pca.h linux-2.6.26.5-new/include/linux/i2c-algo-pca.h
@@ -1,7 +1,11 @@
 #ifndef _LINUX_I2C_ALGO_PCA_H
 #define _LINUX_I2C_ALGO_PCA_H
 
-/* Clock speeds for the bus */
+/* Chips known to the pca algo */
+#define I2C_PCA_CHIP_9564	0x00
+#define I2C_PCA_CHIP_9665	0x01
+
+/* Clock speeds for the bus for PCA9564*/
 #define I2C_PCA_CON_330kHz	0x00
 #define I2C_PCA_CON_288kHz	0x01
 #define I2C_PCA_CON_217kHz	0x02

@@ -18,6 +22,26 @@
 #define I2C_PCA_ADR		0x02 /* OWN ADR Read/Write */
 #define I2C_PCA_CON		0x03 /* CONTROL Read/Write */
 
+/* PCA9665 registers */
+#define I2C_PCA_INDPTR          0x00 /* INDIRECT Pointer Write Only */
+#define I2C_PCA_IND             0x02 /* INDIRECT Read/Write */
+
+/* PCA9665 indirect registers */
+#define I2C_PCA_ICOUNT          0x00 /* Byte Count for buffered mode */
+#define I2C_PCA_IADR            0x01 /* OWN ADR */
+#define I2C_PCA_ISCLL           0x02 /* SCL LOW period */
+#define I2C_PCA_ISCLH           0x03 /* SCL HIGH period */
+#define I2C_PCA_ITO             0x04 /* TIMEOUT */
+#define I2C_PCA_IPRESET         0x05 /* Parallel bus reset */
+#define I2C_PCA_IMODE           0x06 /* I2C Bus mode */
+
+/* PCA9665 I2C bus mode */
+#define I2C_PCA_MODE_STD        0x00 /* Standard mode */
+#define I2C_PCA_MODE_FAST       0x01 /* Fast mode */
+#define I2C_PCA_MODE_FASTP      0x02 /* Fast Plus mode */
+#define I2C_PCA_MODE_TURBO      0x03 /* Turbo mode */
+
+
 #define I2C_PCA_CON_AA		0x80 /* Assert Acknowledge */
 #define I2C_PCA_CON_ENSIO	0x40 /* Enable */
 #define I2C_PCA_CON_STA		0x20 /* Start */

@@ -31,8 +55,11 @@
 	int  (*read_byte)		(void *data, int reg);
 	int  (*wait_for_completion)	(void *data);
 	void (*reset_chip)		(void *data);
-	/* i2c_clock values are defined in linux/i2c-algo-pca.h */
+	/* For PCA9964, use one of the predefined frequencies:
+	 * 330000, 288000, 217000, 146000, 88000, 59000, 44000, 36000
+	 * For PCA9665, use the frequency you want here. */
 	unsigned int			i2c_clock;
+	unsigned int			i2c_chip_type;
 };
 
 int i2c_pca_add_bus(struct i2c_adapter *);

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

#2 lore raw
In reply to a message not in the archive
Quoted 3 lines

Here is the patch against 2.6.26.5.
Please tell me if I did something very wrong ;)

I'm just about to leave the office, so just the first notes. Will have a deeper look later this evening...

drivers/i2c/algos/i2c-algo-pca.c line 51

Quoted 6 lines
drivers/i2c/algos/i2c-algo-pca.c +6 -0
+static void pca9665_reset(void *pd)
+{
+	struct i2c_algo_pca_data *adap = pd;
+	pca_outw(adap,I2C_PCA_INDPTR,I2C_PCA_IPRESET);
+	pca_outw(adap,I2C_PCA_IND,0xA5);
+	pca_outw(adap,I2C_PCA_IND,0x5A);

CodingStyle issues (space after comma)...

drivers/i2c/algos/i2c-algo-pca.c line 347

Quoted 1 line
drivers/i2c/algos/i2c-algo-pca.c +1 -0
+	if (pca_data->i2c_chip_type != I2C_PCA_CHIP_9564 && pca_data->i2c_chip_type != I2C_PCA_CHIP_9665 ) {

Line is longer than 80 chars. Please be sure to have run checkpatch.pl before submitting.

Review

Quoted 1 line
(quoted diff) +1 -0
+

Trailing whitespaces here (and in some other places).

drivers/i2c/algos/i2c-algo-pca.c line 403

Quoted 1 line
drivers/i2c/algos/i2c-algo-pca.c +1 -0
+		int minTLow, minTHi;

This style of naming is at least unusual in kernel. Maybe min_tlow?

So much for now, more later...

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

author
#4 lore raw
In reply to a message not in the archive

Hi Wolfram.

Quoted 3 lines · Wolfram Sang

I'm just about to leave the office, so just the first notes. Will have a deeper look later this evening...

I did the fixes you pointed out and run the script. This is the result.

Regards,

Marco

drivers/i2c/algos/i2c-algo-pca.c +136 -12
diff -ur linux-2.6.26.5/drivers/i2c/algos/i2c-algo-pca.c linux-2.6.26.5-new/drivers/i2c/algos/i2c-algo-pca.c
@@ -43,6 +43,14 @@
 #define pca_wait(adap) adap->wait_for_completion(adap->data)
 #define pca_reset(adap) adap->reset_chip(adap->data)
 
+static void pca9665_reset(void *pd)
+{
+	struct i2c_algo_pca_data *adap = pd;
+	pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_IPRESET);
+	pca_outw(adap, I2C_PCA_IND, 0xA5);
+	pca_outw(adap, I2C_PCA_IND, 0x5A);
+}
+
 /*
  * Generate a start condition on the i2c bus.
  *

@@ -332,24 +340,140 @@
 
 static int pca_init(struct i2c_adapter *adap)
 {
-	static int freqs[] = {330,288,217,146,88,59,44,36};
-	int clock;
 	struct i2c_algo_pca_data *pca_data = adap->algo_data;
 
-	if (pca_data->i2c_clock > 7) {
-		printk(KERN_WARNING "%s: Invalid I2C clock speed selected. Trying default.\n",
-			adap->name);
-		pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+	adap->algo = &pca_algo;
+
+	if (pca_data->i2c_chip_type > I2C_PCA_CHIP_9665) {
+		printk(KERN_WARNING "%s: Invalid chip selected."
+				"Assuming PCA9564.\n", adap->name);
+		pca_data->i2c_chip_type = I2C_PCA_CHIP_9564;
 	}
 
-	adap->algo = &pca_algo;
+	if (pca_data->i2c_chip_type == I2C_PCA_CHIP_9564) {
+		static int freqs[] = {330, 288, 217, 146, 88, 59, 44, 36};
+		int clock;
+
+		if (pca_data->i2c_clock > 7) {
+			switch (pca_data->i2c_clock) {
+			case 330000:
+				pca_data->i2c_clock = I2C_PCA_CON_330kHz;
+				break;
+			case 288000:
+				pca_data->i2c_clock = I2C_PCA_CON_288kHz;
+				break;
+			case 217000:
+				pca_data->i2c_clock = I2C_PCA_CON_217kHz;
+				break;
+			case 146000:
+				pca_data->i2c_clock = I2C_PCA_CON_146kHz;
+				break;
+			case 88000:
+				pca_data->i2c_clock = I2C_PCA_CON_88kHz;
+				break;
+			case 59000:
+				pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+				break;
+			case 44000:
+				pca_data->i2c_clock = I2C_PCA_CON_44kHz;
+				break;
+			case 36000:
+				pca_data->i2c_clock = I2C_PCA_CON_36kHz;
+				break;
+			default:
+				printk(KERN_WARNING
+					"%s: Invalid I2C clock speed selected."
+					"Trying default.\n", adap->name);
+			pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+			}
+		} else {
+			printk(KERN_WARNING "%s: "
+				"Choosing the clock frequency based on "
+				"index is deprecated."
+				" Use the nominal frequency.\n", adap->name);
+		}
+
+		pca_reset(pca_data);
+
+		clock = pca_clock(pca_data);
+		DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n",
+		     adap->name, freqs[clock]);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+	} else {
+		int clock;
+		int mode;
+		int tlow, thigh;
+		int min_tlow, min_thigh;
+		int raise_fall_time;
+
+		struct i2c_algo_pca_data *pca_data = adap->algo_data;
+
+		/* Ignore the reset function from the module,
+		 * we can use the parallel bus reset
+		 */
+		pca_data->reset_chip = pca9665_reset;
+
+		if (pca_data->i2c_clock > 1265800) {
+			printk(KERN_WARNING "%s: I2C clock speed too high."
+				" Using 1265.8kHz.\n", adap->name);
+			pca_data->i2c_clock = 1265800;
+		}
+
+		if (pca_data->i2c_clock < 60300) {
+			printk(KERN_WARNING "%s: I2C clock speed too low."
+				" Using 60.3kHz.\n", adap->name);
+			pca_data->i2c_clock = 60300;
+		}
+
+		clock = pca_clock(pca_data)/100; /* Hz*100 */
 
-	pca_reset(pca_data);
 
-	clock = pca_clock(pca_data);
-	DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);
+		if (pca_data->i2c_clock > 10000) {
+			mode = I2C_PCA_MODE_TURBO;
+			min_tlow = 14;
+			min_thigh  = 5;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 4000) {
+			mode = I2C_PCA_MODE_FASTP;
+			min_tlow = 17;
+			min_thigh  = 9;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 1000) {
+			mode = I2C_PCA_MODE_FAST;
+			min_tlow = 44;
+			min_thigh  = 20;
+			raise_fall_time = 58; /* Raise 29e-8s, Fall 29e-8s */
+		} else {
+			mode = I2C_PCA_MODE_STD;
+			min_tlow = 157;
+			min_thigh  = 134;
+			raise_fall_time = 127; /* Raise 29e-8s, Fall 98e-8s */
+		}
+
+		if (clock < 648) {
+			tlow = 255;
+			thigh = (1000000-clock*raise_fall_time)/(3*clock)-tlow;
+		} else {
+			tlow = ((1000000-clock*raise_fall_time)*min_tlow);
+			tlow /= (3*clock*(min_thigh+min_tlow));
+			thigh = tlow*min_thigh/min_tlow;
+		}
+
+		pca_reset(pca_data);
 
-	pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+		DEB1(KERN_INFO
+		     "%s: Clock frequency is %dHz\n", adap->name, clock*100);
+
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IMODE);
+		pca_outw(pca_data, I2C_PCA_IND, mode);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLL);
+		pca_outw(pca_data, I2C_PCA_IND, tlow);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLH);
+		pca_outw(pca_data, I2C_PCA_IND, thigh);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO);
+	}
 	udelay(500); /* 500 us for oscilator to stabilise */
 
 	return 0;

@@ -384,7 +508,7 @@
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>, "
 	"Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-Bus PCA9564 algorithm");
+MODULE_DESCRIPTION("I2C-Bus PCA9564/PCA9665 algorithm");
 MODULE_LICENSE("GPL");
 
 module_param(i2c_debug, int, 0);
drivers/i2c/busses/i2c-pca-isa.c +14 -4
diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-isa.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-isa.c
@@ -41,7 +41,8 @@
 
 /* Data sheet recommends 59kHz for 100kHz operation due to variation
  * in the actual clock rate */
-static int clock  = I2C_PCA_CON_59kHz;
+static int clock  = 59000;
+static int chip   = I2C_PCA_CHIP_9564;
 
 static wait_queue_head_t pca_wait;
 

@@ -103,7 +104,7 @@
 	.owner          = THIS_MODULE,
 	.id		= I2C_HW_A_ISA,
 	.algo_data	= &pca_isa_data,
-	.name		= "PCA9564 ISA Adapter",
+	.name		= "PCA9564/PCA9665 ISA Adapter",
 	.timeout	= 100,
 };
 

@@ -132,6 +133,7 @@
 		}
 	}
 
+	pca_isa_data.i2c_chip_type = chip;
 	pca_isa_data.i2c_clock = clock;
 	if (i2c_pca_add_bus(&pca_isa_ops) < 0) {
 		dev_err(dev, "Failed to add i2c bus\n");

@@ -182,7 +184,7 @@
 }
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>");
-MODULE_DESCRIPTION("ISA base PCA9564 driver");
+MODULE_DESCRIPTION("ISA base PCA9564/PCA9665 driver");
 MODULE_LICENSE("GPL");
 
 module_param(base, ulong, 0);

@@ -191,7 +193,15 @@
 module_param(irq, int, 0);
 MODULE_PARM_DESC(irq, "IRQ");
 module_param(clock, int, 0);
-MODULE_PARM_DESC(clock, "Clock rate as described in table 1 of PCA9564 datasheet");
+MODULE_PARM_DESC(clock, "Clock rate in hertz.\n\t\t"
+		"For PCA9564: 330000,288000,217000,146000,"
+		"88000,59000,44000,36000\n"
+		"\t\tFor PCA9665:\tStandard: 60300 - 100099\n"
+		"\t\t\t\tFast: 100100 - 400099\n"
+		"\t\t\t\tFast+: 400100 - 10000099\n"
+		"\t\t\t\tTurbo: Up to 1265800");
+module_param(chip, int, 0);
+MODULE_PARM_DESC(chip, "Chip type: 0 = PCA9564; 1 - PCA9665");
 
 module_init(pca_isa_init);
 module_exit(pca_isa_exit);
drivers/i2c/busses/i2c-pca-platform.c +5 -4
diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-platform.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-platform.c
@@ -172,8 +172,9 @@
 
 	i2c->adap.nr = pdev->id >= 0 ? pdev->id : 0;
 	i2c->adap.owner = THIS_MODULE;
-	snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564 at 0x%08lx",
-		(unsigned long) res->start);
+	snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+		 "PCA9564/PCA9665 at 0x%08lx",
+		 (unsigned long) res->start);
 	i2c->adap.algo_data = &i2c->algo_data;
 	i2c->adap.dev.parent = &pdev->dev;
 	i2c->adap.timeout = platform_data->timeout;

@@ -246,7 +247,7 @@
 e_alloc:
 	release_mem_region(res->start, res_len(res));
 e_print:
-	printk(KERN_ERR "Registering PCA9564 FAILED! (%d)\n", ret);
+	printk(KERN_ERR "Registering PCA9564/PCA9665 FAILED! (%d)\n", ret);
 	return ret;
 }
 

@@ -290,7 +291,7 @@
 }
 
 MODULE_AUTHOR("Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-PCA9564 platform driver");
+MODULE_DESCRIPTION("I2C-PCA9564/PCA9665 platform driver");
 MODULE_LICENSE("GPL");
 
 module_init(i2c_pca_pf_init);
drivers/i2c/busses/Kconfig +2 -2
diff -ur linux-2.6.26.5/drivers/i2c/busses/Kconfig linux-2.6.26.5-new/drivers/i2c/busses/Kconfig
@@ -630,7 +630,7 @@
 	  will be called i2c-voodoo3.
 
 config I2C_PCA_ISA
-	tristate "PCA9564 on an ISA bus"
+	tristate "PCA9564/PCA9665 on an ISA bus"
 	depends on ISA
 	select I2C_ALGOPCA
 	default n

@@ -647,7 +647,7 @@
 	  time).  If unsure, say N.
 
 config I2C_PCA_PLATFORM
-	tristate "PCA9564 as platform device"
+	tristate "PCA9564/PCA9665 as platform device"
 	select I2C_ALGOPCA
 	default n
 	help

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

#6 lore raw
In reply to a message not in the archive

Hi Marco,

Quoted 2 lines

I did the fixes you pointed out and run the script. This is the result.

Thanks. This patch is somehow missing the i2c-algo-pca.h changes.

drivers/i2c/algos/i2c-algo-pca.c line 347

Quoted 3 lines
drivers/i2c/algos/i2c-algo-pca.c +3 -0
+	adap->algo = &pca_algo;
+
+	if (pca_data->i2c_chip_type > I2C_PCA_CHIP_9665) {

I wonder if something like I2C_PCA_CHIP_MAXVAL could be useful here. Then, if another chip will be added, you just need changes in the .h file.

Quoted 30 lines
drivers/i2c/algos/i2c-algo-pca.c +27 -1
+		printk(KERN_WARNING "%s: Invalid chip selected."
+				"Assuming PCA9564.\n", adap->name);
+		pca_data->i2c_chip_type = I2C_PCA_CHIP_9564;
 	}
 
-	adap->algo = &pca_algo;
+	if (pca_data->i2c_chip_type == I2C_PCA_CHIP_9564) {
+		static int freqs[] = {330, 288, 217, 146, 88, 59, 44, 36};
+		int clock;
+
+		if (pca_data->i2c_clock > 7) {
+			switch (pca_data->i2c_clock) {
+			case 330000:
+				pca_data->i2c_clock = I2C_PCA_CON_330kHz;
+				break;
+			case 288000:
+				pca_data->i2c_clock = I2C_PCA_CON_288kHz;
+				break;
+			case 217000:
+				pca_data->i2c_clock = I2C_PCA_CON_217kHz;
+				break;
+			case 146000:
+				pca_data->i2c_clock = I2C_PCA_CON_146kHz;
+				break;
+			case 88000:
+				pca_data->i2c_clock = I2C_PCA_CON_88kHz;
+				break;
+			case 59000:
+				pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+				break;

drivers/i2c/algos/i2c-algo-pca.c line 386

Quoted 10 lines
drivers/i2c/algos/i2c-algo-pca.c +10 -0
+			case 44000:
+				pca_data->i2c_clock = I2C_PCA_CON_44kHz;
+				break;
+			case 36000:
+				pca_data->i2c_clock = I2C_PCA_CON_36kHz;
+				break;
+			default:
+				printk(KERN_WARNING
+					"%s: Invalid I2C clock speed selected."
+					"Trying default.\n", adap->name);

Please mention what the default is.

Quoted 33 lines
drivers/i2c/algos/i2c-algo-pca.c +33 -0
+			pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+			}
+		} else {
+			printk(KERN_WARNING "%s: "
+				"Choosing the clock frequency based on "
+				"index is deprecated."
+				" Use the nominal frequency.\n", adap->name);
+		}
+
+		pca_reset(pca_data);
+
+		clock = pca_clock(pca_data);
+		DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n",
+		     adap->name, freqs[clock]);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+	} else {
+		int clock;
+		int mode;
+		int tlow, thigh;
+		int min_tlow, min_thigh;
+		int raise_fall_time;
+
+		struct i2c_algo_pca_data *pca_data = adap->algo_data;
+
+		/* Ignore the reset function from the module,
+		 * we can use the parallel bus reset
+		 */
+		pca_data->reset_chip = pca9665_reset;
+
+		if (pca_data->i2c_clock > 1265800) {
+			printk(KERN_WARNING "%s: I2C clock speed too high."
+				" Using 1265.8kHz.\n", adap->name);

drivers/i2c/algos/i2c-algo-pca.c line 429

Quoted 10 lines
drivers/i2c/algos/i2c-algo-pca.c +10 -0
+			pca_data->i2c_clock = 1265800;
+		}
+
+		if (pca_data->i2c_clock < 60300) {
+			printk(KERN_WARNING "%s: I2C clock speed too low."
+				" Using 60.3kHz.\n", adap->name);
+			pca_data->i2c_clock = 60300;
+		}
+
+		clock = pca_clock(pca_data)/100; /* Hz*100 */

CodingStyle (no spaces around operators)
The comment is also a bit misleading as it is the opposite from the code. Please be a bit more detailed here.

Quoted 20 lines
drivers/i2c/algos/i2c-algo-pca.c +15 -3
-	pca_reset(pca_data);
 
-	clock = pca_clock(pca_data);
-	DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);
+		if (pca_data->i2c_clock > 10000) {
+			mode = I2C_PCA_MODE_TURBO;
+			min_tlow = 14;
+			min_thigh  = 5;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 4000) {
+			mode = I2C_PCA_MODE_FASTP;
+			min_tlow = 17;
+			min_thigh  = 9;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 1000) {
+			mode = I2C_PCA_MODE_FAST;
+			min_tlow = 44;
+			min_thigh  = 20;
+			raise_fall_time = 58; /* Raise 29e-8s, Fall 29e-8s */

drivers/i2c/algos/i2c-algo-pca.c line 456

Quoted 10 lines
drivers/i2c/algos/i2c-algo-pca.c +10 -0
+		} else {
+			mode = I2C_PCA_MODE_STD;
+			min_tlow = 157;
+			min_thigh  = 134;
+			raise_fall_time = 127; /* Raise 29e-8s, Fall 98e-8s */
+		}
+
+		if (clock < 648) {
+			tlow = 255;
+			thigh = (1000000-clock*raise_fall_time)/(3*clock)-tlow;

CodingStyle (no spaces around operators)
The values look a bit magic. I could find min_t*-values in the spec, still a reference to the section of the spec will be helpful. I think you could elaborate a bit more on raise_fall_time and clock < 648, though.

drivers/i2c/algos/i2c-algo-pca.c line 461

Quoted 5 lines
drivers/i2c/algos/i2c-algo-pca.c +5 -0
+		} else {
+			tlow = ((1000000-clock*raise_fall_time)*min_tlow);
+			tlow /= (3*clock*(min_thigh+min_tlow));
+			thigh = tlow*min_thigh/min_tlow;
+		}

CodingStyle (no spaces around operators)

drivers/i2c/algos/i2c-algo-pca.c line 466

Quoted 6 lines
drivers/i2c/algos/i2c-algo-pca.c +4 -1
+
+		pca_reset(pca_data);
 
-	pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+		DEB1(KERN_INFO
+		     "%s: Clock frequency is %dHz\n", adap->name, clock*100);

CodingStyle (no spaces around operators)

Quoted 82 lines
drivers/i2c/algos/i2c-algo-pca.c +11 -1
+
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IMODE);
+		pca_outw(pca_data, I2C_PCA_IND, mode);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLL);
+		pca_outw(pca_data, I2C_PCA_IND, tlow);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLH);
+		pca_outw(pca_data, I2C_PCA_IND, thigh);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO);
+	}
 	udelay(500); /* 500 us for oscilator to stabilise */
 
 	return 0;

@@ -384,7 +508,7 @@
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>, "
 	"Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-Bus PCA9564 algorithm");
+MODULE_DESCRIPTION("I2C-Bus PCA9564/PCA9665 algorithm");
 MODULE_LICENSE("GPL");
 
 module_param(i2c_debug, int, 0);

diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-isa.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-isa.c

drivers/i2c/busses/i2c-pca-isa.c +14 -4
@@ -41,7 +41,8 @@
 
 /* Data sheet recommends 59kHz for 100kHz operation due to variation
  * in the actual clock rate */
-static int clock  = I2C_PCA_CON_59kHz;
+static int clock  = 59000;
+static int chip   = I2C_PCA_CHIP_9564;
 
 static wait_queue_head_t pca_wait;
 

@@ -103,7 +104,7 @@
 	.owner          = THIS_MODULE,
 	.id		= I2C_HW_A_ISA,
 	.algo_data	= &pca_isa_data,
-	.name		= "PCA9564 ISA Adapter",
+	.name		= "PCA9564/PCA9665 ISA Adapter",
 	.timeout	= 100,
 };
 

@@ -132,6 +133,7 @@
 		}
 	}
 
+	pca_isa_data.i2c_chip_type = chip;
 	pca_isa_data.i2c_clock = clock;
 	if (i2c_pca_add_bus(&pca_isa_ops) < 0) {
 		dev_err(dev, "Failed to add i2c bus\n");

@@ -182,7 +184,7 @@
 }
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>");
-MODULE_DESCRIPTION("ISA base PCA9564 driver");
+MODULE_DESCRIPTION("ISA base PCA9564/PCA9665 driver");
 MODULE_LICENSE("GPL");
 
 module_param(base, ulong, 0);

@@ -191,7 +193,15 @@
 module_param(irq, int, 0);
 MODULE_PARM_DESC(irq, "IRQ");
 module_param(clock, int, 0);
-MODULE_PARM_DESC(clock, "Clock rate as described in table 1 of PCA9564 datasheet");
+MODULE_PARM_DESC(clock, "Clock rate in hertz.\n\t\t"
+		"For PCA9564: 330000,288000,217000,146000,"
+		"88000,59000,44000,36000\n"
+		"\t\tFor PCA9665:\tStandard: 60300 - 100099\n"
+		"\t\t\t\tFast: 100100 - 400099\n"
+		"\t\t\t\tFast+: 400100 - 10000099\n"
+		"\t\t\t\tTurbo: Up to 1265800");
+module_param(chip, int, 0);
+MODULE_PARM_DESC(chip, "Chip type: 0 = PCA9564; 1 - PCA9665");
 
 module_init(pca_isa_init);
 module_exit(pca_isa_exit);

diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-platform.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-platform.c

drivers/i2c/busses/i2c-pca-platform.c line 176

Quoted 7 lines
drivers/i2c/busses/i2c-pca-platform.c +2 -2
@@ -172,8 +172,9 @@
 
 	i2c->adap.nr = pdev->id >= 0 ? pdev->id : 0;
 	i2c->adap.owner = THIS_MODULE;
-	snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564 at 0x%08lx",
-		(unsigned long) res->start);
+	snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+		 "PCA9564/PCA9665 at 0x%08lx",

I think we could be precise here as we know the chip-type. I just got the idea: Do you think it is possible to detect the chip type at runtime? Perhaps by somehow checking the presence of the indirect register?

Quoted 44 lines
drivers/i2c/busses/i2c-pca-platform.c +3 -2
+		 (unsigned long) res->start);
 	i2c->adap.algo_data = &i2c->algo_data;
 	i2c->adap.dev.parent = &pdev->dev;
 	i2c->adap.timeout = platform_data->timeout;

@@ -246,7 +247,7 @@
 e_alloc:
 	release_mem_region(res->start, res_len(res));
 e_print:
-	printk(KERN_ERR "Registering PCA9564 FAILED! (%d)\n", ret);
+	printk(KERN_ERR "Registering PCA9564/PCA9665 FAILED! (%d)\n", ret);
 	return ret;
 }
 

@@ -290,7 +291,7 @@
 }
 
 MODULE_AUTHOR("Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-PCA9564 platform driver");
+MODULE_DESCRIPTION("I2C-PCA9564/PCA9665 platform driver");
 MODULE_LICENSE("GPL");
 
 module_init(i2c_pca_pf_init);

diff -ur linux-2.6.26.5/drivers/i2c/busses/Kconfig linux-2.6.26.5-new/drivers/i2c/busses/Kconfig

drivers/i2c/busses/Kconfig +2 -2
@@ -630,7 +630,7 @@
 	  will be called i2c-voodoo3.
 
 config I2C_PCA_ISA
-	tristate "PCA9564 on an ISA bus"
+	tristate "PCA9564/PCA9665 on an ISA bus"
 	depends on ISA
 	select I2C_ALGOPCA
 	default n

@@ -647,7 +647,7 @@
 	  time).  If unsure, say N.
 
 config I2C_PCA_PLATFORM
-	tristate "PCA9564 as platform device"
+	tristate "PCA9564/PCA9665 as platform device"
 	select I2C_ALGOPCA
 	default n
 	help
Quoted 4 lines

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

I haven't really applied the patch yet. Will do on Monday when I have access to the PCA9564-equipped board.

All the best,

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

author
#8 lore raw
In reply to a message not in the archive

Hi Wolfram

Quoted 5 lines · Wolfram Sang
Quoted 1 line

+ if (pca_data->i2c_chip_type > I2C_PCA_CHIP_9665) {

I wonder if something like I2C_PCA_CHIP_MAXVAL could be useful here. Then, if another chip will be added, you just need changes in the .h file.

You are right. Done.

Quoted 6 lines

drivers/i2c/algos/i2c-algo-pca.c line 386

Quoted 4 lines
drivers/i2c/algos/i2c-algo-pca.c +4 -0
+                     default:
+                             printk(KERN_WARNING
+                                     "%s: Invalid I2C clock speed selected."
+                                     "Trying default.\n", adap->name);

Please mention what the default is.

Done.

Quoted 5 lines
Quoted 1 line

+ clock = pca_clock(pca_data)/100; /* Hz*100 */

CodingStyle (no spaces around operators)
The comment is also a bit misleading as it is the opposite from the code. Please be a bit more detailed here.

Done.

Quoted 9 lines

drivers/i2c/algos/i2c-algo-pca.c line 456

Quoted 3 lines
drivers/i2c/algos/i2c-algo-pca.c +3 -0
+             if (clock < 648) {
+                     tlow = 255;
+                     thigh = (1000000-clock*raise_fall_time)/(3*clock)-tlow;

CodingStyle (no spaces around operators)
The values look a bit magic. I could find min_t*-values in the spec, still a reference to the section of the spec will be helpful. I think you could elaborate a bit more on raise_fall_time and clock < 648, though.

Done.

Quoted 9 lines

drivers/i2c/busses/i2c-pca-platform.c line 176

Quoted 4 lines
drivers/i2c/busses/i2c-pca-platform.c +2 -2
-     snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564 at 0x%08lx",
-             (unsigned long) res->start);
+     snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+              "PCA9564/PCA9665 at 0x%08lx",

I think we could be precise here as we know the chip-type. I just got the idea: Do you think it is possible to detect the chip type at runtime? Perhaps by somehow checking the presence of the indirect register?

I thought the same before, but I was afraid that it would be too much of a hack. As the user has to know which chip he has (there is no auto-detection at all for this), I thought that this is not really a necessity. I can do it if you think that it is a good idea.

I will send you the corrected patch after your comment on the auto-detection issue.

Best regards,

Marco

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

author
#10 lore raw
In reply to a message not in the archive

Hi Wolfram.

Quoted 3 lines · Marco Aurelio da Costa

I will send you the corrected patch after your comment on the auto-detection issue.

Actually, I changed my mind and implemented the auto-detection code. Here is the new patch.

Regards,

Marco

drivers/i2c/algos/i2c-algo-pca.c +170 -12
diff -ur linux-2.6.26.5/drivers/i2c/algos/i2c-algo-pca.c linux-2.6.26.5-new/drivers/i2c/algos/i2c-algo-pca.c
@@ -43,6 +43,14 @@
 #define pca_wait(adap) adap->wait_for_completion(adap->data)
 #define pca_reset(adap) adap->reset_chip(adap->data)
 
+static void pca9665_reset(void *pd)
+{
+	struct i2c_algo_pca_data *adap = pd;
+	pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_IPRESET);
+	pca_outw(adap, I2C_PCA_IND, 0xA5);
+	pca_outw(adap, I2C_PCA_IND, 0x5A);
+}
+
 /*
  * Generate a start condition on the i2c bus.
  *

@@ -330,26 +338,176 @@
 	.functionality	= pca_func,
 };
 
-static int pca_init(struct i2c_adapter *adap)
+static unsigned int pca_probe_chip(struct i2c_adapter *adap)
 {
-	static int freqs[] = {330,288,217,146,88,59,44,36};
-	int clock;
 	struct i2c_algo_pca_data *pca_data = adap->algo_data;
-
-	if (pca_data->i2c_clock > 7) {
-		printk(KERN_WARNING "%s: Invalid I2C clock speed selected. Trying default.\n",
+	/* The trick here is to check if there is an indirect register
+	 * available. If there is one, we will read the value we first
+	 * wrote on I2C_PCA_IADR. Otherwise, we will read the last value
+	 * we wrote on I2C_PCA_ADR
+	 */
+	pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IADR);
+	pca_outw(pca_data, I2C_PCA_IND, 0xAA);
+	pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ITO);
+	pca_outw(pca_data, I2C_PCA_IND, 0x00);
+	pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IADR);
+	if (pca_inw(pca_data, I2C_PCA_IND) == 0xAA) {
+		printk(KERN_INFO
+			"%s: PCA9665 detected.",
 			adap->name);
-		pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+		 return I2C_PCA_CHIP_9665;
+	} else {
+		printk(KERN_INFO
+			"%s: PCA9564 detected.",
+			adap->name);
+		return I2C_PCA_CHIP_9564;
 	}
+}
+
+static int pca_init(struct i2c_adapter *adap)
+{
+	struct i2c_algo_pca_data *pca_data = adap->algo_data;
 
 	adap->algo = &pca_algo;
 
-	pca_reset(pca_data);
+	if (pca_probe_chip(adap) == I2C_PCA_CHIP_9564) {
+		static int freqs[] = {330, 288, 217, 146, 88, 59, 44, 36};
+		int clock;
+
+		if (pca_data->i2c_clock > 7) {
+			switch (pca_data->i2c_clock) {
+			case 330000:
+				pca_data->i2c_clock = I2C_PCA_CON_330kHz;
+				break;
+			case 288000:
+				pca_data->i2c_clock = I2C_PCA_CON_288kHz;
+				break;
+			case 217000:
+				pca_data->i2c_clock = I2C_PCA_CON_217kHz;
+				break;
+			case 146000:
+				pca_data->i2c_clock = I2C_PCA_CON_146kHz;
+				break;
+			case 88000:
+				pca_data->i2c_clock = I2C_PCA_CON_88kHz;
+				break;
+			case 59000:
+				pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+				break;
+			case 44000:
+				pca_data->i2c_clock = I2C_PCA_CON_44kHz;
+				break;
+			case 36000:
+				pca_data->i2c_clock = I2C_PCA_CON_36kHz;
+				break;
+			default:
+				printk(KERN_WARNING
+					"%s: Invalid I2C clock speed selected."
+					"Using default 59kHz.\n", adap->name);
+			pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+			}
+		} else {
+			printk(KERN_WARNING "%s: "
+				"Choosing the clock frequency based on "
+				"index is deprecated."
+				" Use the nominal frequency.\n", adap->name);
+		}
+
+		pca_reset(pca_data);
+
+		clock = pca_clock(pca_data);
+		DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n",
+		     adap->name, freqs[clock]);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+	} else {
+		int clock;
+		int mode;
+		int tlow, thi;
+		/* Values can be found on PCA9665 datasheet section 7.3.2.6 */
+		int min_tlow, min_thi;
+		/* These values are the maximum raise and fall values allowed
+		 * by the I2C operation mode (Standard, Fast or Fast+)
+		 * They are used (added) below to calculate the clock dividers
+		 * of PCA9665. Note that they are slightly different of the
+		 * real maximum, to allow the change on mode exactly on the
+		 * maximum clock rate for each mode
+		 */
+		int raise_fall_time;
+
+		struct i2c_algo_pca_data *pca_data = adap->algo_data;
+
+		/* Ignore the reset function from the module,
+		 * we can use the parallel bus reset
+		 */
+		pca_data->reset_chip = pca9665_reset;
+
+		if (pca_data->i2c_clock > 1265800) {
+			printk(KERN_WARNING "%s: I2C clock speed too high."
+				" Using 1265.8kHz.\n", adap->name);
+			pca_data->i2c_clock = 1265800;
+		}
+
+		if (pca_data->i2c_clock < 60300) {
+			printk(KERN_WARNING "%s: I2C clock speed too low."
+				" Using 60.3kHz.\n", adap->name);
+			pca_data->i2c_clock = 60300;
+		}
+
+		/* To avoid integer overflow, use clock/100 for calculations */
+		clock = pca_clock(pca_data)/100;
 
-	clock = pca_clock(pca_data);
-	DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);
 
-	pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+		if (pca_data->i2c_clock > 10000) {
+			mode = I2C_PCA_MODE_TURBO;
+			min_tlow = 14;
+			min_thi  = 5;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 4000) {
+			mode = I2C_PCA_MODE_FASTP;
+			min_tlow = 17;
+			min_thi  = 9;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 1000) {
+			mode = I2C_PCA_MODE_FAST;
+			min_tlow = 44;
+			min_thi  = 20;
+			raise_fall_time = 58; /* Raise 29e-8s, Fall 29e-8s */
+		} else {
+			mode = I2C_PCA_MODE_STD;
+			min_tlow = 157;
+			min_thi  = 134;
+			raise_fall_time = 127; /* Raise 29e-8s, Fall 98e-8s */
+		}
+
+		/* The minimum clock that respects the thi/tlow = 134/157 is
+		 * 64800 Hz. Below that, we have to fix the tlow to 255 and
+		 * calculate the thi factor.
+		 */
+		if (clock < 648) {
+			tlow = 255;
+			thi = 1000000 - clock * raise_fall_time;
+			thi /= (I2C_PCA_OSC_PER * clock) - tlow;
+		} else {
+			tlow = (1000000 - clock * raise_fall_time) * min_tlow;
+			tlow /= I2C_PCA_OSC_PER * clock * (min_thi + min_tlow);
+			thi = tlow * min_thi / min_tlow;
+		}
+
+		pca_reset(pca_data);
+
+		DEB1(KERN_INFO
+		     "%s: Clock frequency is %dHz\n", adap->name, clock * 100);
+
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IMODE);
+		pca_outw(pca_data, I2C_PCA_IND, mode);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLL);
+		pca_outw(pca_data, I2C_PCA_IND, tlow);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLH);
+		pca_outw(pca_data, I2C_PCA_IND, thi);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO);
+	}
 	udelay(500); /* 500 us for oscilator to stabilise */
 
 	return 0;

@@ -384,7 +542,7 @@
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>, "
 	"Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-Bus PCA9564 algorithm");
+MODULE_DESCRIPTION("I2C-Bus PCA9564/PCA9665 algorithm");
 MODULE_LICENSE("GPL");
 
 module_param(i2c_debug, int, 0);
drivers/i2c/busses/i2c-pca-isa.c +10 -4
diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-isa.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-isa.c
@@ -41,7 +41,7 @@
 
 /* Data sheet recommends 59kHz for 100kHz operation due to variation
  * in the actual clock rate */
-static int clock  = I2C_PCA_CON_59kHz;
+static int clock  = 59000;
 
 static wait_queue_head_t pca_wait;
 

@@ -103,7 +103,7 @@
 	.owner          = THIS_MODULE,
 	.id		= I2C_HW_A_ISA,
 	.algo_data	= &pca_isa_data,
-	.name		= "PCA9564 ISA Adapter",
+	.name		= "PCA9564/PCA9665 ISA Adapter",
 	.timeout	= 100,
 };
 

@@ -182,7 +182,7 @@
 }
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>");
-MODULE_DESCRIPTION("ISA base PCA9564 driver");
+MODULE_DESCRIPTION("ISA base PCA9564/PCA9665 driver");
 MODULE_LICENSE("GPL");
 
 module_param(base, ulong, 0);

@@ -191,7 +191,13 @@
 module_param(irq, int, 0);
 MODULE_PARM_DESC(irq, "IRQ");
 module_param(clock, int, 0);
-MODULE_PARM_DESC(clock, "Clock rate as described in table 1 of PCA9564 datasheet");
+MODULE_PARM_DESC(clock, "Clock rate in hertz.\n\t\t"
+		"For PCA9564: 330000,288000,217000,146000,"
+		"88000,59000,44000,36000\n"
+		"\t\tFor PCA9665:\tStandard: 60300 - 100099\n"
+		"\t\t\t\tFast: 100100 - 400099\n"
+		"\t\t\t\tFast+: 400100 - 10000099\n"
+		"\t\t\t\tTurbo: Up to 1265800");
 
 module_init(pca_isa_init);
 module_exit(pca_isa_exit);
drivers/i2c/busses/i2c-pca-platform.c +5 -4
diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-platform.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-platform.c
@@ -172,8 +172,9 @@
 
 	i2c->adap.nr = pdev->id >= 0 ? pdev->id : 0;
 	i2c->adap.owner = THIS_MODULE;
-	snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564 at 0x%08lx",
-		(unsigned long) res->start);
+	snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+		 "PCA9564/PCA9665 at 0x%08lx",
+		 (unsigned long) res->start);
 	i2c->adap.algo_data = &i2c->algo_data;
 	i2c->adap.dev.parent = &pdev->dev;
 	i2c->adap.timeout = platform_data->timeout;

@@ -246,7 +247,7 @@
 e_alloc:
 	release_mem_region(res->start, res_len(res));
 e_print:
-	printk(KERN_ERR "Registering PCA9564 FAILED! (%d)\n", ret);
+	printk(KERN_ERR "Registering PCA9564/PCA9665 FAILED! (%d)\n", ret);
 	return ret;
 }
 

@@ -290,7 +291,7 @@
 }
 
 MODULE_AUTHOR("Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-PCA9564 platform driver");
+MODULE_DESCRIPTION("I2C-PCA9564/PCA9665 platform driver");
 MODULE_LICENSE("GPL");
 
 module_init(i2c_pca_pf_init);
drivers/i2c/busses/Kconfig +2 -2
diff -ur linux-2.6.26.5/drivers/i2c/busses/Kconfig linux-2.6.26.5-new/drivers/i2c/busses/Kconfig
@@ -630,7 +630,7 @@
 	  will be called i2c-voodoo3.
 
 config I2C_PCA_ISA
-	tristate "PCA9564 on an ISA bus"
+	tristate "PCA9564/PCA9665 on an ISA bus"
 	depends on ISA
 	select I2C_ALGOPCA
 	default n

@@ -647,7 +647,7 @@
 	  time).  If unsure, say N.
 
 config I2C_PCA_PLATFORM
-	tristate "PCA9564 as platform device"
+	tristate "PCA9564/PCA9665 as platform device"
 	select I2C_ALGOPCA
 	default n
 	help
include/linux/i2c-algo-pca.h +31 -2
diff -ur linux-2.6.26.5/include/linux/i2c-algo-pca.h linux-2.6.26.5-new/include/linux/i2c-algo-pca.h
@@ -1,7 +1,14 @@
 #ifndef _LINUX_I2C_ALGO_PCA_H
 #define _LINUX_I2C_ALGO_PCA_H
 
-/* Clock speeds for the bus */
+/* Chips known to the pca algo */
+#define I2C_PCA_CHIP_9564	0x00
+#define I2C_PCA_CHIP_9665	0x01
+
+/* Internal period for PCA9665 oscilator */
+#define I2C_PCA_OSC_PER		3 /* e10-8s */
+
+/* Clock speeds for the bus for PCA9564*/
 #define I2C_PCA_CON_330kHz	0x00
 #define I2C_PCA_CON_288kHz	0x01
 #define I2C_PCA_CON_217kHz	0x02

@@ -18,6 +25,26 @@
 #define I2C_PCA_ADR		0x02 /* OWN ADR Read/Write */
 #define I2C_PCA_CON		0x03 /* CONTROL Read/Write */
 
+/* PCA9665 registers */
+#define I2C_PCA_INDPTR          0x00 /* INDIRECT Pointer Write Only */
+#define I2C_PCA_IND             0x02 /* INDIRECT Read/Write */
+
+/* PCA9665 indirect registers */
+#define I2C_PCA_ICOUNT          0x00 /* Byte Count for buffered mode */
+#define I2C_PCA_IADR            0x01 /* OWN ADR */
+#define I2C_PCA_ISCLL           0x02 /* SCL LOW period */
+#define I2C_PCA_ISCLH           0x03 /* SCL HIGH period */
+#define I2C_PCA_ITO             0x04 /* TIMEOUT */
+#define I2C_PCA_IPRESET         0x05 /* Parallel bus reset */
+#define I2C_PCA_IMODE           0x06 /* I2C Bus mode */
+
+/* PCA9665 I2C bus mode */
+#define I2C_PCA_MODE_STD        0x00 /* Standard mode */
+#define I2C_PCA_MODE_FAST       0x01 /* Fast mode */
+#define I2C_PCA_MODE_FASTP      0x02 /* Fast Plus mode */
+#define I2C_PCA_MODE_TURBO      0x03 /* Turbo mode */
+
+
 #define I2C_PCA_CON_AA		0x80 /* Assert Acknowledge */
 #define I2C_PCA_CON_ENSIO	0x40 /* Enable */
 #define I2C_PCA_CON_STA		0x20 /* Start */

@@ -31,7 +58,9 @@
 	int  (*read_byte)		(void *data, int reg);
 	int  (*wait_for_completion)	(void *data);
 	void (*reset_chip)		(void *data);
-	/* i2c_clock values are defined in linux/i2c-algo-pca.h */
+	/* For PCA9964, use one of the predefined frequencies:
+	 * 330000, 288000, 217000, 146000, 88000, 59000, 44000, 36000
+	 * For PCA9665, use the frequency you want here. */
 	unsigned int			i2c_clock;
 };

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

author
#12 lore raw
In reply to a message not in the archive

Hi Wolfram.

Did you have time to look into the patch I sent?

Thank you in advance,

Marco

Quoted 6 lines · Marco Aurelio da Costa

Hi Wolfram.

Quoted 3 lines · Marco Aurelio da Costa

I will send you the corrected patch after your comment on the auto-detection issue.

Quoted 7 lines

Actually, I changed my mind and implemented the auto-detection code. Here is the new patch.

Regards,

Marco

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

#14 lore raw
In reply to a message not in the archive

Hi Marco,

Quoted 1 line · Marco Aurelio da Costa

Did you have time to look into the patch I sent?

I had a look and found very minor issues only (spaces around operators), still I haven't had the time to actually test it on my pca9564-device. I haven't forgotten, but it is one of those weeks... :(

All the best,

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

Reviewed-by
#15 lore raw
In reply to a message not in the archive

Hi Marco,

finally I came around to setup my board with the PCA9564. Here are my
results: The algo detected the PCA9564 and moaned about the old style of supplying the frequency. I could easily change it to newstyle. In every case, I could still correctly read out the eeprom. So, everything worked flawlessly with a PCA9564. So, if the PCA9665 works for you and you just apply these minor suggestions below, I think the patch is ready for submission. For that, you should follow the canocical patch format (Documentation/SubmittingPatches, Chapter 15) when you post that version.

Reviewed-by Wolfram Sang <[email protected]>
Quoted 47 lines · Marco Aurelio da Costa

Hi Wolfram.

Quoted 3 lines · Marco Aurelio da Costa

I will send you the corrected patch after your comment on the auto-detection issue.

Actually, I changed my mind and implemented the auto-detection code. Here is the new patch.

Regards,

Marco

diff -ur linux-2.6.26.5/drivers/i2c/algos/i2c-algo-pca.c linux-2.6.26.5-new/drivers/i2c/algos/i2c-algo-pca.c

drivers/i2c/algos/i2c-algo-pca.c +12 -6
@@ -43,6 +43,14 @@
 #define pca_wait(adap) adap->wait_for_completion(adap->data)
 #define pca_reset(adap) adap->reset_chip(adap->data)
 
+static void pca9665_reset(void *pd)
+{
+	struct i2c_algo_pca_data *adap = pd;
+	pca_outw(adap, I2C_PCA_INDPTR, I2C_PCA_IPRESET);
+	pca_outw(adap, I2C_PCA_IND, 0xA5);
+	pca_outw(adap, I2C_PCA_IND, 0x5A);
+}
+
 /*
  * Generate a start condition on the i2c bus.
  *

@@ -330,26 +338,176 @@
 	.functionality	= pca_func,
 };
 
-static int pca_init(struct i2c_adapter *adap)
+static unsigned int pca_probe_chip(struct i2c_adapter *adap)
 {
-	static int freqs[] = {330,288,217,146,88,59,44,36};
-	int clock;
 	struct i2c_algo_pca_data *pca_data = adap->algo_data;
-
-	if (pca_data->i2c_clock > 7) {
-		printk(KERN_WARNING "%s: Invalid I2C clock speed selected. Trying default.\n",
+	/* The trick here is to check if there is an indirect register
+	 * available. If there is one, we will read the value we first
+	 * wrote on I2C_PCA_IADR. Otherwise, we will read the last value

drivers/i2c/algos/i2c-algo-pca.c line 356

Quoted 10 lines
drivers/i2c/algos/i2c-algo-pca.c +10 -0
+	 * we wrote on I2C_PCA_ADR
+	 */
+	pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IADR);
+	pca_outw(pca_data, I2C_PCA_IND, 0xAA);
+	pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ITO);
+	pca_outw(pca_data, I2C_PCA_IND, 0x00);
+	pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IADR);
+	if (pca_inw(pca_data, I2C_PCA_IND) == 0xAA) {
+		printk(KERN_INFO
+			"%s: PCA9665 detected.",

"\n" is missing. Also, the whole printk should fit into one line.

drivers/i2c/algos/i2c-algo-pca.c line 361

Quoted 6 lines
drivers/i2c/algos/i2c-algo-pca.c +4 -1
 			adap->name);
-		pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+		 return I2C_PCA_CHIP_9665;
+	} else {
+		printk(KERN_INFO
+			"%s: PCA9564 detected.",

Here, too.

Quoted 36 lines
drivers/i2c/algos/i2c-algo-pca.c +31 -1
+			adap->name);
+		return I2C_PCA_CHIP_9564;
 	}
+}
+
+static int pca_init(struct i2c_adapter *adap)
+{
+	struct i2c_algo_pca_data *pca_data = adap->algo_data;
 
 	adap->algo = &pca_algo;
 
-	pca_reset(pca_data);
+	if (pca_probe_chip(adap) == I2C_PCA_CHIP_9564) {
+		static int freqs[] = {330, 288, 217, 146, 88, 59, 44, 36};
+		int clock;
+
+		if (pca_data->i2c_clock > 7) {
+			switch (pca_data->i2c_clock) {
+			case 330000:
+				pca_data->i2c_clock = I2C_PCA_CON_330kHz;
+				break;
+			case 288000:
+				pca_data->i2c_clock = I2C_PCA_CON_288kHz;
+				break;
+			case 217000:
+				pca_data->i2c_clock = I2C_PCA_CON_217kHz;
+				break;
+			case 146000:
+				pca_data->i2c_clock = I2C_PCA_CON_146kHz;
+				break;
+			case 88000:
+				pca_data->i2c_clock = I2C_PCA_CON_88kHz;
+				break;
+			case 59000:
+				pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+				break;

drivers/i2c/algos/i2c-algo-pca.c line 406

Quoted 10 lines
drivers/i2c/algos/i2c-algo-pca.c +10 -0
+			case 44000:
+				pca_data->i2c_clock = I2C_PCA_CON_44kHz;
+				break;
+			case 36000:
+				pca_data->i2c_clock = I2C_PCA_CON_36kHz;
+				break;
+			default:
+				printk(KERN_WARNING
+					"%s: Invalid I2C clock speed selected."
+					"Using default 59kHz.\n", adap->name);

Space before "Using".

Quoted 42 lines
drivers/i2c/algos/i2c-algo-pca.c +42 -0
+			pca_data->i2c_clock = I2C_PCA_CON_59kHz;
+			}
+		} else {
+			printk(KERN_WARNING "%s: "
+				"Choosing the clock frequency based on "
+				"index is deprecated."
+				" Use the nominal frequency.\n", adap->name);
+		}
+
+		pca_reset(pca_data);
+
+		clock = pca_clock(pca_data);
+		DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n",
+		     adap->name, freqs[clock]);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+	} else {
+		int clock;
+		int mode;
+		int tlow, thi;
+		/* Values can be found on PCA9665 datasheet section 7.3.2.6 */
+		int min_tlow, min_thi;
+		/* These values are the maximum raise and fall values allowed
+		 * by the I2C operation mode (Standard, Fast or Fast+)
+		 * They are used (added) below to calculate the clock dividers
+		 * of PCA9665. Note that they are slightly different of the
+		 * real maximum, to allow the change on mode exactly on the
+		 * maximum clock rate for each mode
+		 */
+		int raise_fall_time;
+
+		struct i2c_algo_pca_data *pca_data = adap->algo_data;
+
+		/* Ignore the reset function from the module,
+		 * we can use the parallel bus reset
+		 */
+		pca_data->reset_chip = pca9665_reset;
+
+		if (pca_data->i2c_clock > 1265800) {
+			printk(KERN_WARNING "%s: I2C clock speed too high."
+				" Using 1265.8kHz.\n", adap->name);
+			pca_data->i2c_clock = 1265800;

drivers/i2c/algos/i2c-algo-pca.c line 458

Quoted 10 lines
drivers/i2c/algos/i2c-algo-pca.c +10 -0
+		}
+
+		if (pca_data->i2c_clock < 60300) {
+			printk(KERN_WARNING "%s: I2C clock speed too low."
+				" Using 60.3kHz.\n", adap->name);
+			pca_data->i2c_clock = 60300;
+		}
+
+		/* To avoid integer overflow, use clock/100 for calculations */
+		clock = pca_clock(pca_data)/100;

Spaces around operators.

Quoted 213 lines
drivers/i2c/algos/i2c-algo-pca.c +51 -4
-	clock = pca_clock(pca_data);
-	DEB1(KERN_INFO "%s: Clock frequency is %dkHz\n", adap->name, freqs[clock]);
 
-	pca_set_con(pca_data, I2C_PCA_CON_ENSIO | clock);
+		if (pca_data->i2c_clock > 10000) {
+			mode = I2C_PCA_MODE_TURBO;
+			min_tlow = 14;
+			min_thi  = 5;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 4000) {
+			mode = I2C_PCA_MODE_FASTP;
+			min_tlow = 17;
+			min_thi  = 9;
+			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
+		} else if (pca_data->i2c_clock > 1000) {
+			mode = I2C_PCA_MODE_FAST;
+			min_tlow = 44;
+			min_thi  = 20;
+			raise_fall_time = 58; /* Raise 29e-8s, Fall 29e-8s */
+		} else {
+			mode = I2C_PCA_MODE_STD;
+			min_tlow = 157;
+			min_thi  = 134;
+			raise_fall_time = 127; /* Raise 29e-8s, Fall 98e-8s */
+		}
+
+		/* The minimum clock that respects the thi/tlow = 134/157 is
+		 * 64800 Hz. Below that, we have to fix the tlow to 255 and
+		 * calculate the thi factor.
+		 */
+		if (clock < 648) {
+			tlow = 255;
+			thi = 1000000 - clock * raise_fall_time;
+			thi /= (I2C_PCA_OSC_PER * clock) - tlow;
+		} else {
+			tlow = (1000000 - clock * raise_fall_time) * min_tlow;
+			tlow /= I2C_PCA_OSC_PER * clock * (min_thi + min_tlow);
+			thi = tlow * min_thi / min_tlow;
+		}
+
+		pca_reset(pca_data);
+
+		DEB1(KERN_INFO
+		     "%s: Clock frequency is %dHz\n", adap->name, clock * 100);
+
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_IMODE);
+		pca_outw(pca_data, I2C_PCA_IND, mode);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLL);
+		pca_outw(pca_data, I2C_PCA_IND, tlow);
+		pca_outw(pca_data, I2C_PCA_INDPTR, I2C_PCA_ISCLH);
+		pca_outw(pca_data, I2C_PCA_IND, thi);
+
+		pca_set_con(pca_data, I2C_PCA_CON_ENSIO);
+	}
 	udelay(500); /* 500 us for oscilator to stabilise */
 
 	return 0;

@@ -384,7 +542,7 @@
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>, "
 	"Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-Bus PCA9564 algorithm");
+MODULE_DESCRIPTION("I2C-Bus PCA9564/PCA9665 algorithm");
 MODULE_LICENSE("GPL");
 
 module_param(i2c_debug, int, 0);

diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-isa.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-isa.c

drivers/i2c/busses/i2c-pca-isa.c +10 -4
@@ -41,7 +41,7 @@
 
 /* Data sheet recommends 59kHz for 100kHz operation due to variation
  * in the actual clock rate */
-static int clock  = I2C_PCA_CON_59kHz;
+static int clock  = 59000;
 
 static wait_queue_head_t pca_wait;
 

@@ -103,7 +103,7 @@
 	.owner          = THIS_MODULE,
 	.id		= I2C_HW_A_ISA,
 	.algo_data	= &pca_isa_data,
-	.name		= "PCA9564 ISA Adapter",
+	.name		= "PCA9564/PCA9665 ISA Adapter",
 	.timeout	= 100,
 };
 

@@ -182,7 +182,7 @@
 }
 
 MODULE_AUTHOR("Ian Campbell <[email protected]>");
-MODULE_DESCRIPTION("ISA base PCA9564 driver");
+MODULE_DESCRIPTION("ISA base PCA9564/PCA9665 driver");
 MODULE_LICENSE("GPL");
 
 module_param(base, ulong, 0);

@@ -191,7 +191,13 @@
 module_param(irq, int, 0);
 MODULE_PARM_DESC(irq, "IRQ");
 module_param(clock, int, 0);
-MODULE_PARM_DESC(clock, "Clock rate as described in table 1 of PCA9564 datasheet");
+MODULE_PARM_DESC(clock, "Clock rate in hertz.\n\t\t"
+		"For PCA9564: 330000,288000,217000,146000,"
+		"88000,59000,44000,36000\n"
+		"\t\tFor PCA9665:\tStandard: 60300 - 100099\n"
+		"\t\t\t\tFast: 100100 - 400099\n"
+		"\t\t\t\tFast+: 400100 - 10000099\n"
+		"\t\t\t\tTurbo: Up to 1265800");
 
 module_init(pca_isa_init);
 module_exit(pca_isa_exit);

diff -ur linux-2.6.26.5/drivers/i2c/busses/i2c-pca-platform.c linux-2.6.26.5-new/drivers/i2c/busses/i2c-pca-platform.c

drivers/i2c/busses/i2c-pca-platform.c +5 -4
@@ -172,8 +172,9 @@
 
 	i2c->adap.nr = pdev->id >= 0 ? pdev->id : 0;
 	i2c->adap.owner = THIS_MODULE;
-	snprintf(i2c->adap.name, sizeof(i2c->adap.name), "PCA9564 at 0x%08lx",
-		(unsigned long) res->start);
+	snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+		 "PCA9564/PCA9665 at 0x%08lx",
+		 (unsigned long) res->start);
 	i2c->adap.algo_data = &i2c->algo_data;
 	i2c->adap.dev.parent = &pdev->dev;
 	i2c->adap.timeout = platform_data->timeout;

@@ -246,7 +247,7 @@
 e_alloc:
 	release_mem_region(res->start, res_len(res));
 e_print:
-	printk(KERN_ERR "Registering PCA9564 FAILED! (%d)\n", ret);
+	printk(KERN_ERR "Registering PCA9564/PCA9665 FAILED! (%d)\n", ret);
 	return ret;
 }
 

@@ -290,7 +291,7 @@
 }
 
 MODULE_AUTHOR("Wolfram Sang <[email protected]>");
-MODULE_DESCRIPTION("I2C-PCA9564 platform driver");
+MODULE_DESCRIPTION("I2C-PCA9564/PCA9665 platform driver");
 MODULE_LICENSE("GPL");
 
 module_init(i2c_pca_pf_init);

diff -ur linux-2.6.26.5/drivers/i2c/busses/Kconfig linux-2.6.26.5-new/drivers/i2c/busses/Kconfig

drivers/i2c/busses/Kconfig +2 -2
@@ -630,7 +630,7 @@
 	  will be called i2c-voodoo3.
 
 config I2C_PCA_ISA
-	tristate "PCA9564 on an ISA bus"
+	tristate "PCA9564/PCA9665 on an ISA bus"
 	depends on ISA
 	select I2C_ALGOPCA
 	default n

@@ -647,7 +647,7 @@
 	  time).  If unsure, say N.
 
 config I2C_PCA_PLATFORM
-	tristate "PCA9564 as platform device"
+	tristate "PCA9564/PCA9665 as platform device"
 	select I2C_ALGOPCA
 	default n
 	help

diff -ur linux-2.6.26.5/include/linux/i2c-algo-pca.h linux-2.6.26.5-new/include/linux/i2c-algo-pca.h

include/linux/i2c-algo-pca.h +28 -1
@@ -1,7 +1,14 @@
 #ifndef _LINUX_I2C_ALGO_PCA_H
 #define _LINUX_I2C_ALGO_PCA_H
 
-/* Clock speeds for the bus */
+/* Chips known to the pca algo */
+#define I2C_PCA_CHIP_9564	0x00
+#define I2C_PCA_CHIP_9665	0x01
+
+/* Internal period for PCA9665 oscilator */
+#define I2C_PCA_OSC_PER		3 /* e10-8s */
+
+/* Clock speeds for the bus for PCA9564*/
 #define I2C_PCA_CON_330kHz	0x00
 #define I2C_PCA_CON_288kHz	0x01
 #define I2C_PCA_CON_217kHz	0x02

@@ -18,6 +25,26 @@
 #define I2C_PCA_ADR		0x02 /* OWN ADR Read/Write */
 #define I2C_PCA_CON		0x03 /* CONTROL Read/Write */
 
+/* PCA9665 registers */
+#define I2C_PCA_INDPTR          0x00 /* INDIRECT Pointer Write Only */
+#define I2C_PCA_IND             0x02 /* INDIRECT Read/Write */
+
+/* PCA9665 indirect registers */
+#define I2C_PCA_ICOUNT          0x00 /* Byte Count for buffered mode */
+#define I2C_PCA_IADR            0x01 /* OWN ADR */
+#define I2C_PCA_ISCLL           0x02 /* SCL LOW period */
+#define I2C_PCA_ISCLH           0x03 /* SCL HIGH period */
+#define I2C_PCA_ITO             0x04 /* TIMEOUT */
+#define I2C_PCA_IPRESET         0x05 /* Parallel bus reset */
+#define I2C_PCA_IMODE           0x06 /* I2C Bus mode */
+
+/* PCA9665 I2C bus mode */
+#define I2C_PCA_MODE_STD        0x00 /* Standard mode */
+#define I2C_PCA_MODE_FAST       0x01 /* Fast mode */
+#define I2C_PCA_MODE_FASTP      0x02 /* Fast Plus mode */
+#define I2C_PCA_MODE_TURBO      0x03 /* Turbo mode */
+
+
 #define I2C_PCA_CON_AA		0x80 /* Assert Acknowledge */
 #define I2C_PCA_CON_ENSIO	0x40 /* Enable */
 #define I2C_PCA_CON_STA		0x20 /* Start */

include/linux/i2c-algo-pca.h line 61

Quoted 5 lines
include/linux/i2c-algo-pca.h +1 -1
@@ -31,7 +58,9 @@
 	int  (*read_byte)		(void *data, int reg);
 	int  (*wait_for_completion)	(void *data);
 	void (*reset_chip)		(void *data);
-	/* i2c_clock values are defined in linux/i2c-algo-pca.h */
+	/* For PCA9964, use one of the predefined frequencies:

Typo: Not 9964, but 9564

Quoted 10 lines
include/linux/i2c-algo-pca.h +2 -0
+	 * 330000, 288000, 217000, 146000, 88000, 59000, 44000, 36000
+	 * For PCA9665, use the frequency you want here. */
 	unsigned int			i2c_clock;
 };

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

All the best and thanks for the patch!

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

author
#17 lore raw
In reply to a message not in the archive

Hi Wolfram.

Quoted 11 lines · Wolfram Sang

Hi Marco,

finally I came around to setup my board with the PCA9564. Here are my
results: The algo detected the PCA9564 and moaned about the old style of supplying the frequency. I could easily change it to newstyle. In every case, I could still correctly read out the eeprom. So, everything worked flawlessly with a PCA9564. So, if the PCA9665 works for you and you just apply these minor suggestions below, I think the patch is ready for submission. For that, you should follow the canocical patch format (Documentation/SubmittingPatches, Chapter 15) when you post that version.

Glad to hear! I will make the changes as you sugests and submit the patch as soon as possible. I am out of office for some time.

Quoted 3 lines

All the best and thanks for the patch!

The comunity helps me so much, It is just fair that I give something back.

Best regards,

Marco

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

#19 lore raw
In reply to a message not in the archive

Hi Marco,

Quoted 2 lines · Marco Aurelio da Costa

Glad to hear! I will make the changes as you sugests and submit the patch as soon as possible. I am out of office for some time.

Any news on your patch?

All the best,

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry

_______________________________________________
i2c mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/i2c

#22 lore raw
In reply to a message not in the archive

Hi Marco,

Quoted 5 lines · Marco Aurelio da Costa
Quoted 1 line

Any news on your patch?

Actually I am in Brazil. I will not be able to really test it until the end of November, when I go back to Germany.
I am sorry for the delay.

Bump ;)

Regards,

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry
#24 lore raw
In reply to a message not in the archive
Quoted 9 lines · Wolfram Sang

Hi Marco,

Quoted 5 lines · Marco Aurelio da Costa
Quoted 1 line

Any news on your patch?

Actually I am in Brazil. I will not be able to really test it until the end of November, when I go back to Germany.
I am sorry for the delay.

Marco, are you back from Brazil?

Regards,

Wolfram

Signature · 2 lines
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry