CFI driver and P33 64M flash
Hi,
I'm running U-Boot 1.3.4 on custom 460EX based board, equipped with 64M P33 flash (similar to Intel P30). See
http://www.numonyx.com/Documents/Datasheets/314749_P33_Discrete_DS.pdf
This flash is comprised internally of two 32M flashes. I have the following declarations in configuration file:
#define CFG_FLASH_CFI /* The flash is CFI compatible */
#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 518 /* max number of sectors on one
chip */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x
faster) */
#define CFG_FLASH_PROTECTION 1 /* use hardware flash
protection */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on
flinfo */
U-Boot identifies this flash as 32M flash. Below is debug output from CFI driver:
FLASH: flash detect cfi
fwc addr fc000000 cmd f0 f0 8bit x 8 bit
fwc addr fc000000 cmd ff ff 8bit x 8 bit
fwc addr fc000055 cmd 98 98 8bit x 8 bit
is= cmd 51(Q) addr fc000010 is= 0 51
fwc addr fc000555 cmd 98 98 8bit x 8 bit
is= cmd 51(Q) addr fc000010 is= 0 51
fwc addr fc000000 cmd f0 f0f0 16bit x 8 bit
fwc addr fc000000 cmd ff ffff 16bit x 8 bit
fwc addr fc0000aa cmd 98 9898 16bit x 8 bit
is= cmd 51(Q) addr fc000020 is= 0051 5151
fwc addr fc000aaa cmd 98 9898 16bit x 8 bit
is= cmd 51(Q) addr fc000020 is= 0051 5151
fwc addr fc000000 cmd f0 00f0 16bit x 16 bit
fwc addr fc000000 cmd ff 00ff 16bit x 16 bit
fwc addr fc0000aa cmd 98 0098 16bit x 16 bit
is= cmd 51(Q) addr fc000020 is= 0051 0051
is= cmd 52(R) addr fc000022 is= 0052 0052
is= cmd 59(Y) addr fc000024 is= 0059 0059
device interface is 1
found port 2 chip 2 port 16 bits chip 16 bits
00 : 51 52 59 01 00 0a 01 00 00 00 00 23 36 85 95 08 QRY........#6... 10 : 09 0a 00 01 01 02 00 19 01 00 06 00 02 03 00 80 ................ 20 : 00 fe 00 00 02 00 00 00 00 ff ff ff ff fc 36 a4 ..............6.
fwc addr fc000000 cmd ff 00ff 16bit x 16 bit fwc addr fc000000 cmd 90 0090 16bit x 16 bit fwc addr fc000000 cmd ff 00ff 16bit x 16 bit fwc addr fc0000aa cmd 98 0098 16bit x 16 bit manufacturer is 1
manufacturer id is 0x89
device id is 0x22
device id2 is 0x0
cfi version is 0x3135size_ratio 1 port 16 bits chip 16 bits found 2 erase regions
erase region 0: 0x00800003 erase_region_count = 4 erase_region_size = 32768 erase region 1: 0x020000fe erase_region_count = 255 erase_region_size = 131072 fwc addr fc000000 cmd ff 00ff 16bit x 16 bit 32 MB
What should I change in configuration/driver to get all 64M of flash detected ?
Thanks a lot.
Felix.
Quoted 5 lines · Felix Radensky
I'm running U-Boot 1.3.4 on custom 460EX based board, equipped with 64M P33 flash (similar to Intel P30). See
http://www.numonyx.com/Documents/Datasheets/314749_P33_Discrete_DS.pdfThis flash is comprised internally of two 32M flashes.
Then you have to define 2 physical chips in your U-Boot configuration.
Quoted 7 lines
I have the following declarations in configuration file:
#define
CFG_FLASH_CFI/* The flash is CFI compatible */
#defineCFG_FLASH_CFI_DRIVER/* Use common CFI driver */#define
CFG_FLASH_BANKS_LIST{CFG_FLASH_BASE}
#defineCFG_MAX_FLASH_BANKS1 /* max number of memory banks */
This will not work. Take a look at the lwmon5 configuration. It has a similar Intel FLASH which has two chips inside:
#define CFG_FLASH0 0xFC000000
#define CFG_FLASH1 0xF8000000
#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }#define CFG_MAX_FLASH_BANKS 2
...
You need to change the addresses for your 32MB version though.
Hope this helps.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
Dear Stefan Roese,
Quoted 8 lines · In message <[email protected]> you wrote:
This will not work. Take a look at the lwmon5 configuration. It has a similar Intel FLASH which has two chips inside:
#define CFG_FLASH0 0xFC000000 #define CFG_FLASH1 0xF8000000 #define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }
Quoted 5 lines
#define
CFG_MAX_FLASH_BANKS2...
You need to change the addresses for your 32MB version though.
Please note that I really dislike such static configurations which will break as soon as the size of the flash banks changes.
Right from the begining U-Boot was always designed to allow for dynamic adjustment to the actual memory sizes found on the boards, and we should just use this capability.
Assuming a 32 bit configuration, above should rather be written as:
#define CFG_FLASH0 (0 - flash_info[0].size)
#define CFG_FLASH1 (CFG_FLASH0 - flash_info[1].size)
#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }
...
This may require a preliminary mapping of the flash banks that is then fixed after the CFI driver determined the real size; see for example how this was done for the TQM8xx* boards (of course this needs to be adapted for 4xx, but you get the idea).
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "We don't care. We don't have to. We're the Phone Company."
Hi, Stefan
Quoted 28 lines · Stefan Roese
Quoted 6 lines · Felix Radensky
I'm running U-Boot 1.3.4 on custom 460EX based board, equipped with 64M P33 flash (similar to Intel P30). See
http://www.numonyx.com/Documents/Datasheets/314749_P33_Discrete_DS.pdfThis flash is comprised internally of two 32M flashes.
Then you have to define 2 physical chips in your U-Boot configuration.
Quoted 8 lines
I have the following declarations in configuration file:
#define
CFG_FLASH_CFI/* The flash is CFI compatible */
#defineCFG_FLASH_CFI_DRIVER/* Use common CFI driver */#define
CFG_FLASH_BANKS_LIST{CFG_FLASH_BASE}
#defineCFG_MAX_FLASH_BANKS1 /* max number of memory banks */This will not work. Take a look at the lwmon5 configuration. It has a similar Intel FLASH which has two chips inside:
#define CFG_FLASH0 0xFC000000 #define CFG_FLASH1 0xF8000000 #define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }
Quoted 6 lines
#define
CFG_MAX_FLASH_BANKS2...
You need to change the addresses for your 32MB version though.
Using 2 flash banks works fine. Thanks a lot for a prompt reply.
Felix.
Hi,
I have a similar p30 intel 64M flash.When I try to initialize both banks at 0x20000000 and 0x22000000, u-boot crashes while initializing second bank at 0x22000000, i debugged and found out that u-boot couldn't sucessfully write to second bank. But when i plug in the debugger to my board i can see and use the second bank starting at 0x22000000.
Though if i initialize only first bank everything runs normal but i am left with 32Mb of space.
I am going bonkers over this, please help .
Quoted 83 lines · Felix Radensky
Hi,
I'm running U-Boot 1.3.4 on custom 460EX based board, equipped with 64M P33 flash (similar to Intel P30). See
http://www.numonyx.com/Documents/Datasheets/314749_P33_Discrete_DS.pdfThis flash is comprised internally of two 32M flashes. I have the following declarations in configuration file:
#define
CFG_FLASH_CFI/* The flash is CFI compatible */
#defineCFG_FLASH_CFI_DRIVER/* Use common CFI driver */#define
CFG_FLASH_BANKS_LIST{CFG_FLASH_BASE}
#defineCFG_MAX_FLASH_BANKS1 /* max number of memory banks
*/
#defineCFG_MAX_FLASH_SECT518 /* max number of sectors on one
chip */#define
CFG_FLASH_USE_BUFFER_WRITE1 /* use buffered writes (20x
faster) */
#defineCFG_FLASH_PROTECTION1 /* use hardware flash
protection */
#defineCFG_FLASH_EMPTY_INFO/* print 'E' for empty sector on
flinfo */U-Boot identifies this flash as 32M flash. Below is debug output from CFI driver:
FLASH: flash detect cfi
fwc addrfc000000cmd f0 f0 8bit x 8 bit
fwc addrfc000000cmd ff ff 8bit x 8 bit
fwc addrfc000055cmd 98 98 8bit x 8 bit
is= cmd 51(Q) addrfc000010is= 0 51
fwc addrfc000555cmd 98 98 8bit x 8 bit
is= cmd 51(Q) addrfc000010is= 0 51
fwc addrfc000000cmd f0 f0f0 16bit x 8 bit
fwc addrfc000000cmd ff ffff 16bit x 8 bit
fwc addrfc0000aacmd 98 9898 16bit x 8 bit
is= cmd 51(Q) addrfc000020is= 0051 5151
fwc addrfc000aaacmd 98 9898 16bit x 8 bit
is= cmd 51(Q) addrfc000020is= 0051 5151
fwc addrfc000000cmd f0 00f0 16bit x 16 bit
fwc addrfc000000cmd ff 00ff 16bit x 16 bit
fwc addrfc0000aacmd 98 0098 16bit x 16 bit
is= cmd 51(Q) addrfc000020is= 0051 0051
is= cmd 52(R) addrfc000022is= 0052 0052
is= cmd 59(Y) addrfc000024is= 0059 0059
device interface is 1
found port 2 chip 2 port 16 bits chip 16 bits00 : 51 52 59 01 00 0a 01 00 00 00 00 23 36 85 95 08 QRY........#6... 10 : 09 0a 00 01 01 02 00 19 01 00 06 00 02 03 00 80 ................ 20 : 00 fe 00 00 02 00 00 00 00 ff ff ff ff fc 36 a4 ..............6.fwc addr
fc000000cmd ff 00ff 16bit x 16 bit fwc addrfc000000cmd 90 0090 16bit x 16 bit fwc addrfc000000cmd ff 00ff 16bit x 16 bit fwc addrfc0000aacmd 98 0098 16bit x 16 bit manufacturer is 1
manufacturer id is0x89
device id is0x22
device id2 is0x0
cfi version is0x3135size_ratio1 port 16 bits chip 16 bits found 2 erase regions
erase region 0:0x00800003erase_region_count= 4erase_region_size= 32768 erase region 1:0x020000feerase_region_count= 255erase_region_size= 131072 fwc addrfc000000cmd ff 00ff 16bit x 16 bit 32 MBWhat should I change in configuration/driver to get all 64M of flash detected ?
Thanks a lot.
Felix.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 2 lines
View this message in context: http://www.nabble.com/-U-Boot--CFI-driver-and-P33-64M-flash-tp19669949p24815971.html Sent from the Uboot - Users mailing list archive at Nabble.com.