Skip to contentSkip to conversation

dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller

PATCH Superseded Nicolas Ferre 3 participants 8 messages Oct 17, 2008 – Dec 4, 2008

Subsystems (5)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller

This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip.
On other products, it will be used also for peripheral DMA transfer (slave API support to come).

I used dmatest client without problem in different configurations to test it.

Full documentation for this controller can be found in the SAM9RL datasheet :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

---

arch/arm/mach-at91/at91sam9rl_devices.c |   47 ++
drivers/dma/Kconfig                     |    8 +
drivers/dma/Makefile                    |    1 +
drivers/dma/at_hdmac.c                  |  989 +++++++++++++++++++++++++++++++
drivers/dma/at_hdmac_regs.h             |  377 ++++++++++++
include/linux/at_hdmac.h                |   26 +
6 files changed, 1448 insertions(+), 0 deletions(-)
arch/arm/mach-at91/at91sam9rl_devices.c +0 -0
index 87deb1e..ad596ff 100644
@@ -9,6 +9,7 @@

#include <asm/mach/arch.h>
#include <asm/mach/map.h>

+#include <linux/at_hdmac.h>
#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
@@ -26,6 +27,51 @@

/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */ +
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE) +static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 2,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9RL_ID_DMA,
+ .end = AT91SAM9RL_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
+/* --------------------------------------------------------------------
* USB HS Device (Gadget)
* -------------------------------------------------------------------- */

@@ -1114,6 +1160,7 @@ void __init at91_add_device_serial(void) {}
*/
static int __init at91_add_standard_devices(void)
{

+	at91_add_device_hdmac();
	at91_add_device_rtc();
	at91_add_device_rtt();
	at91_add_device_watchdog();
drivers/dma/Kconfig +0 -0
index cd30390..03bfd8f 100644
@@ -47,6 +47,14 @@ config DW_DMAC

Support the Synopsys DesignWare AHB DMA controller. This can be integrated in chips such as the Atmel AT32ap7000.

+config AT_HDMAC
+ tristate "Atmel AHB DMA support"
+ depends on ARCH_AT91 && ARCH_AT91SAM9RL
+ select DMA_ENGINE
+ help
+ Support the Atmel AHB DMA controller. This can be integrated in
+ chips such as the Atmel AT91SAM9RL.
+
config FSL_DMA
bool "Freescale MPC85xx/MPC83xx DMA support" depends on PPC

drivers/dma/Makefile +0 -0
index 14f5952..9c8ce35 100644
@@ -7,3 +7,4 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o

obj-$(CONFIG_FSL_DMA) += fsldma.o
obj-$(CONFIG_MV_XOR) += mv_xor.o
obj-$(CONFIG_DW_DMAC) += dw_dmac.o
+obj-$(CONFIG_AT_HDMAC) += at_hdmac.o

drivers/dma/at_hdmac.c new file +989 -0

989 lines not on this page · raw message

drivers/dma/at_hdmac_regs.h new file +377 -0

377 lines not on this page · raw message

include/linux/at_hdmac.h new file +26 -0
new file mode 100644
index 0000000..21a5554
@@ -0,0 +1,26 @@
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_H
+#define AT_HDMAC_H
+
+#include <linux/dmaengine.h>
+
+/**
+ * struct at_dma_platform_data - Controller configuration parameters
+ * @nr_channels: Number of channels supported by hardware (max 8)
+ * @cap_mask: dma_capability flags supported by the platform
+ */
+struct at_dma_platform_data {
+	unsigned int	nr_channels;
+	dma_cap_mask_t  cap_mask;
+};
+
+#endif /* AT_HDMAC_H */
Signature · 1 line
1.5.3.7
#1 lore raw
Quoted 8 lines · Nicolas Ferre

This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip.
On other products, it will be used also for peripheral DMA transfer (slave API support to come).

Quoted 8 lines

I used dmatest client without problem in different configurations to test it.

Full documentation for this controller can be found in the SAM9RL datasheet :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

---

Hi Nicolas,

A few comments below.

Also, checkpatch reported:

total: 4 errors, 45 warnings, 1475 lines checked

...mostly 80 column warnings (some you may want to take a look at).

Regards,
Dan

Quoted 6 lines
 arch/arm/mach-at91/at91sam9rl_devices.c |   47 ++
 drivers/dma/Kconfig                     |    8 +
 drivers/dma/Makefile                    |    1 +
 drivers/dma/at_hdmac.c                  |  989 +++++++++++++++++++++++++++++++
 drivers/dma/at_hdmac_regs.h             |  377 ++++++++++++
 include/linux/at_hdmac.h                |   26 +

...this header should be moved somewhere under arch/arm/include.

Quoted 176 lines
 6 files changed, 1448 insertions(+), 0 deletions(-)
arch/arm/mach-at91/at91sam9rl_devices.c +47 -0
index 87deb1e..ad596ff 100644
@@ -9,6 +9,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include <linux/at_hdmac.h>
 #include <linux/dma-mapping.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
@@ -26,6 +27,51 @@
 
 
 /* --------------------------------------------------------------------
+ *  HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+       .nr_channels    = 2,
+};
+
+static struct resource hdmac_resources[] = {
+       [0] = {
+               .start  = AT91_BASE_SYS + AT91_DMA,
+               .end    = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+               .flags  = IORESOURCE_MEM,
+       },
+       [2] = {
+               .start  = AT91SAM9RL_ID_DMA,
+               .end    = AT91SAM9RL_ID_DMA,
+               .flags  = IORESOURCE_IRQ,
+       },
+};
+
+static struct platform_device at_hdmac_device = {
+       .name           = "at_hdmac",
+       .id             = -1,
+       .dev            = {
+                               .dma_mask               = &hdmac_dmamask,
+                               .coherent_dma_mask      = DMA_BIT_MASK(32),
+                               .platform_data          = &atdma_pdata,
+       },
+       .resource       = hdmac_resources,
+       .num_resources  = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+       dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+       platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
+/* --------------------------------------------------------------------
  *  USB HS Device (Gadget)
  * -------------------------------------------------------------------- */
 
@@ -1114,6 +1160,7 @@ void __init at91_add_device_serial(void) {}
  */
 static int __init at91_add_standard_devices(void)
 {
+       at91_add_device_hdmac();
        at91_add_device_rtc();
        at91_add_device_rtt();
        at91_add_device_watchdog();
drivers/dma/Kconfig +8 -0
index cd30390..03bfd8f 100644
@@ -47,6 +47,14 @@ config DW_DMAC
          Support the Synopsys DesignWare AHB DMA controller.  This
          can be integrated in chips such as the Atmel AT32ap7000.
 
+config AT_HDMAC
+       tristate "Atmel AHB DMA support"
+       depends on ARCH_AT91 && ARCH_AT91SAM9RL
+       select DMA_ENGINE
+       help
+         Support the Atmel AHB DMA controller.  This can be integrated in
+         chips such as the Atmel AT91SAM9RL.
+
 config FSL_DMA
        bool "Freescale MPC85xx/MPC83xx DMA support"
        depends on PPC
drivers/dma/Makefile +1 -0
index 14f5952..9c8ce35 100644
@@ -7,3 +7,4 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o
 obj-$(CONFIG_FSL_DMA) += fsldma.o
 obj-$(CONFIG_MV_XOR) += mv_xor.o
 obj-$(CONFIG_DW_DMAC) += dw_dmac.o
+obj-$(CONFIG_AT_HDMAC) += at_hdmac.o
drivers/dma/at_hdmac.c new file +68 -0
new file mode 100644
index 0000000..2f0a386
@@ -0,0 +1,989 @@
+/*
+ * Driver for the Atmel AHB DMA Controller (aka HDMA or DMAC on AT91 systems)
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ *
+ * This supports the Atmel AHB DMA Controller,
+ *
+ * The driver has currently been tested with the Atmel AT91SAM9RL
+ * and AT91SAM9M10.
+ */
+
+#include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "at_hdmac_regs.h"
+
+/*
+ * Glossary
+ * --------
+ *
+ * at_hdmac            : Name of the ATmel AHB DMA Controller
+ * at_dma_ / atdma     : ATmel DMA controller entity related
+ * atc_        / atchan        : ATmel DMA Channel entity related
+ */
+
+#define        ATC_DEFAULT_CFG         (ATC_FIFOCFG_HALFFIFO)
+#define        ATC_DEFAULT_CTRLA       (0)
+#define        ATC_DEFAULT_CTRLB       ( ATC_SIF(0)    \
+                               | ATC_DIF(1))
+
+/*
+ * Initial number of descriptors to allocate for each channel. This could
+ * be increased of this amount during dma usage.
+ */
+#define INIT_NR_DESCS_PER_CHANNEL      16
+
+/* prototypes */
+static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx);
+
+
+/*----------------------------------------------------------------------*/
+
+static struct at_desc *atc_first_active(struct at_dma_chan *atchan)
+{
+       return list_first_entry(&atchan->active_list, struct at_desc, desc_node);
+}
+
+static struct at_desc *atc_first_queued(struct at_dma_chan *atchan)
+{
+       return list_first_entry(&atchan->queue, struct at_desc, desc_node);
+}
+
+/**
+ * atc_alloc_descriptor - allocate and return an initilized descriptor
+ * @chan: the channel to allocate descriptors for
+ * @gfp_flags: GFP allocation flags
+ */

drivers/dma/at_hdmac.c line 78

Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+static struct at_desc *atc_alloc_descriptor(struct dma_chan *chan,
+                                           gfp_t gfp_flags)
+{
+       struct at_desc  *desc = NULL;
+       struct at_dma   *atdma = to_at_dma(chan->device);
+       dma_addr_t phys;
+
+       desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys);
+       if (desc) {
+               BUG_ON(phys & 0x3UL); /* descriptors have to be word aligned */

hmm, yes this is a bug but can't we trust that dma_pool_alloc does its job correctly?

drivers/dma/at_hdmac.c line 81

Quoted 3 lines
drivers/dma/at_hdmac.c new file +3 -0
+               memset(desc, 0, sizeof(struct at_desc));
+               dma_async_tx_descriptor_init(&desc->txd, chan);
+               async_tx_ack(&desc->txd);

the DMA_CTRL_ACK bit is under control of the client. It should be read-only to the driver (except for extra descriptors that the driver creates on behalf of the client).

Quoted 30 lines
drivers/dma/at_hdmac.c new file +30 -0
+               desc->txd.tx_submit = atc_tx_submit;
+               INIT_LIST_HEAD(&desc->txd.tx_list);
+               desc->txd.phys = phys;
+       }
+
+       return desc;
+}
+
+/**
+ * atc_desc_get - get a unsused descriptor from free_list
+ * @atchan: channel we want a new descriptor for
+ */
+static struct at_desc *atc_desc_get(struct at_dma_chan *atchan)
+{
+       struct at_desc *desc, *_desc;
+       struct at_desc *ret = NULL;
+       unsigned int i = 0;
+       LIST_HEAD(tmp_list);
+
+       spin_lock_bh(&atchan->lock);
+       list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) {
+               if (async_tx_test_ack(&desc->txd)) {
+                       list_del(&desc->desc_node);
+                       ret = desc;
+                       break;
+               }
+               dev_dbg(&atchan->chan_common.dev, "desc %p not ACKed\n", desc);
+               i++;
+       }
+       spin_unlock_bh(&atchan->lock);

drivers/dma/at_hdmac.c line 121

Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+
+       dev_vdbg(&atchan->chan_common.dev, "scanned %u descriptors on freelist\n", i);
+
+       /* no more descriptor available in initial pool : create some more */
+       if (!ret) {
+               for (i = 0; i < INIT_NR_DESCS_PER_CHANNEL; i++) {
+                       desc = atc_alloc_descriptor(&atchan->chan_common, GFP_KERNEL);
+                       if (!desc)
+                               break;
+                       /* return first descripor, queue others in free_list */

sp: descriptor

Quoted 316 lines
drivers/dma/at_hdmac.c new file +316 -0
+                       if (i)
+                               list_add_tail(&desc->desc_node, &tmp_list);
+                       else
+                               ret = desc;
+               }
+
+               spin_lock_bh(&atchan->lock);
+               atchan->descs_allocated += i;
+               list_splice(&tmp_list, &atchan->free_list);
+               spin_unlock_bh(&atchan->lock);
+       }
+
+       return ret;
+}
+
+/**
+ * atc_desc_put - move a descriptor, including any children, to the free list
+ * @atchan: channel we work on
+ * @desc: descriptor, at the head of a chain, to move to free list
+ */
+static void atc_desc_put(struct at_dma_chan *atchan, struct at_desc *desc)
+{
+       if (desc) {
+               struct at_desc *child;
+
+               spin_lock_bh(&atchan->lock);
+               list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+                       dev_vdbg(&atchan->chan_common.dev,
+                                       "moving child desc %p to freelist\n",
+                                       child);
+               list_splice_init(&desc->txd.tx_list, &atchan->free_list);
+               dev_vdbg(&atchan->chan_common.dev, "moving desc %p to freelist\n", desc);
+               list_add(&desc->desc_node, &atchan->free_list);
+               spin_unlock_bh(&atchan->lock);
+       }
+}
+
+/**
+ * atc_assign_cookie - compute and assign new cookie
+ * @atchan: channel we work on
+ * @desc: descriptor to asign cookie for
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static dma_cookie_t
+atc_assign_cookie(struct at_dma_chan *atchan, struct at_desc *desc)
+{
+       dma_cookie_t cookie = atchan->chan_common.cookie;
+
+       if (++cookie < 0)
+               cookie = 1;
+
+       atchan->chan_common.cookie = cookie;
+       desc->txd.cookie = cookie;
+
+       return cookie;
+}
+
+/**
+ * atc_dostart - starts the DMA engine for real
+ * @atchan: the channel we want to start
+ * @first: first descriptor in the list we want to begin with
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_dostart(struct at_dma_chan *atchan, struct at_desc *first)
+{
+       struct at_dma   *atdma = to_at_dma(atchan->chan_common.device);
+
+       /* ASSERT:  channel is idle */
+       if (atc_chan_is_enabled(atchan)) {
+               dev_err(&atchan->chan_common.dev,
+                       "BUG: Attempted to start non-idle channel\n");
+               dev_err(&atchan->chan_common.dev,
+                       "  channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+                       channel_readl(atchan, SADDR),
+                       channel_readl(atchan, DADDR),
+                       channel_readl(atchan, CTRLA),
+                       channel_readl(atchan, CTRLB),
+                       channel_readl(atchan, DSCR));
+
+               /* The tasklet will hopefully advance the queue... */
+               return;
+       }
+
+       vdbg_dump_regs(atchan);
+
+       /* clear any pending interrupt */
+       while (dma_readl(atdma, EBCISR))
+               cpu_relax();
+
+       channel_writel(atchan, SADDR, 0);
+       channel_writel(atchan, DADDR, 0);
+       channel_writel(atchan, CTRLA, 0);
+       channel_writel(atchan, CTRLB, 0);
+       channel_writel(atchan, DSCR, first->txd.phys);
+       dma_writel(atdma, CHER, atchan->mask);
+
+       vdbg_dump_regs(atchan);
+}
+
+/**
+ * atc_chain_complete - finish work for one transaction chain
+ * @atchan: channel we work on
+ * @desc: descriptor at the head of the chain we want do complete
+ *
+ * Called with atchan->lock held and bh disabled */
+static void
+atc_chain_complete(struct at_dma_chan *atchan, struct at_desc *desc)
+{
+       dma_async_tx_callback           callback;
+       void                            *param;
+       struct dma_async_tx_descriptor  *txd = &desc->txd;
+
+       dev_vdbg(&atchan->chan_common.dev, "descriptor %u complete\n", txd->cookie);
+
+       atchan->completed_cookie = txd->cookie;
+       callback = txd->callback;
+       param = txd->callback_param;
+
+       /* move children to free_list */
+       list_splice_init(&txd->tx_list, &atchan->free_list);
+       /* move myself to free_list */
+       list_move(&desc->desc_node, &atchan->free_list);
+
+       /*
+        * We use dma_unmap_page() regardless of how the buffers were
+        * mapped before they were submitted...
+        */
+       if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP))
+               dma_unmap_page(atchan->chan_common.dev.parent, desc->lli.daddr, desc->len,
+                               DMA_FROM_DEVICE);
+       if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP))
+               dma_unmap_page(atchan->chan_common.dev.parent, desc->lli.saddr, desc->len,
+                               DMA_TO_DEVICE);
+
+       /*
+        * The API requires that no submissions are done from a
+        * callback, so we don't need to drop the lock here
+        */
+       if (callback)
+               callback(param);
+}
+
+/**
+ * atc_complete_all - finish work for all transactions
+ * @atchan: channel to complete transactions for
+ *
+ * Eventually submit queued descriptors if any
+ *
+ * Assume channel is idle while calling this function
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_complete_all(struct at_dma_chan *atchan)
+{
+       struct at_desc *desc, *_desc;
+       LIST_HEAD(list);
+
+       dev_vdbg(&atchan->chan_common.dev, "complete all\n");
+
+       BUG_ON(atc_chan_is_enabled(atchan));
+
+       /*
+        * Submit queued descriptors ASAP, i.e. before we go through
+        * the completed ones.
+        */
+       if (!list_empty(&atchan->queue))
+               atc_dostart(atchan, atc_first_queued(atchan));
+       /* empty active_list now it is completed */
+       list_splice_init(&atchan->active_list, &list);
+       /* empty queue list by moving descriptors (if any) to active_list */
+       list_splice_init(&atchan->queue, &atchan->active_list);
+
+       list_for_each_entry_safe(desc, _desc, &list, desc_node)
+               atc_chain_complete(atchan, desc);
+}
+
+/**
+ * atc_cleanup_descriptors - cleanup up finished descriptors in active_list
+ * @atchan: channel to be cleaned up
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_cleanup_descriptors(struct at_dma_chan *atchan)
+{
+       struct at_desc  *desc, *_desc;
+       struct at_desc  *child;
+
+       dev_vdbg(&atchan->chan_common.dev, "cleanup descriptors\n");
+
+       list_for_each_entry_safe(desc, _desc, &atchan->active_list, desc_node) {
+               if (!(desc->lli.ctrla & ATC_DONE))
+                       /* This one is currently in progress */
+                       return;
+
+               list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+                       if (!(child->lli.ctrla & ATC_DONE))
+                               /* Currently in progress */
+                               return;
+
+               /*
+                * No descriptors so far seem to be in progress, i.e.
+                * this chain must be done.
+                */
+               atc_chain_complete(atchan, desc);
+       }
+}
+
+/**
+ * atc_advance_work - at the end of a transaction, move forward
+ * @atchan: channel where the transaction ended
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_advance_work(struct at_dma_chan *atchan)
+{
+       dev_vdbg(&atchan->chan_common.dev, "advance_work\n");
+
+       if (   list_empty(&atchan->active_list)
+           || list_is_singular(&atchan->active_list)) {
+               atc_complete_all(atchan);
+       } else {
+               atc_chain_complete(atchan, atc_first_active(atchan));
+               /* advance work */
+               atc_dostart(atchan, atc_first_active(atchan));
+       }
+}
+
+
+/**
+ * atc_handle_error - handle errors reported by DMA controller
+ * @atchan: channel where error occurs
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_handle_error(struct at_dma_chan *atchan)
+{
+       struct at_desc *bad_desc;
+       struct at_desc *child;
+
+       /*
+        * The descriptor currently at the head of the active list is
+        * broked. Since we don't have any way to report errors, we'll
+        * just have to scream loudly and try to carry on.
+        */
+       bad_desc = atc_first_active(atchan);
+       list_del_init(&bad_desc->desc_node);
+
+       /* As we are stopped, take advantage to push queued descriptors
+        * in active_list */
+       list_splice_init(&atchan->queue, atchan->active_list.prev);
+
+       /* Try to restart the controller */
+       if (!list_empty(&atchan->active_list))
+               atc_dostart(atchan, atc_first_active(atchan));
+
+       /*
+        * KERN_CRITICAL may seem harsh, but since this only happens
+        * when someone submits a bad physical address in a
+        * descriptor, we should consider ourselves lucky that the
+        * controller flagged an error instead of scribbling over
+        * random memory locations.
+        */
+       dev_crit(&atchan->chan_common.dev,
+                       "Bad descriptor submitted for DMA!\n");
+       dev_crit(&atchan->chan_common.dev,
+                       "  cookie: %d\n", bad_desc->txd.cookie);
+       atc_dump_lli(atchan, &bad_desc->lli);
+       list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node)
+               atc_dump_lli(atchan, &child->lli);
+
+       /* Pretend the descriptor completed successfully */
+       atc_chain_complete(atchan, bad_desc);
+}
+
+
+/*--  IRQ & Tasklet  ---------------------------------------------------*/
+
+static void atc_tasklet(unsigned long data)
+{
+       struct at_dma_chan *atchan = (struct at_dma_chan *)data;
+
+       /* Channel cannot be enabled here */
+       if (atc_chan_is_enabled(atchan)) {
+               dev_err(&atchan->chan_common.dev,
+                       "BUG: channel enabled in tasklet\n");
+               return;
+       }
+
+       spin_lock(&atchan->lock);
+       if (test_and_clear_bit(0, &atchan->error_status))
+               atc_handle_error(atchan);
+       else
+               atc_advance_work(atchan);
+
+       spin_unlock(&atchan->lock);
+}
+
+static irqreturn_t at_dma_interrupt(int irq, void *dev_id)
+{
+       struct at_dma           *atdma = (struct at_dma *)dev_id;
+       struct at_dma_chan      *atchan;
+       int                     i;
+       u32                     status, pending, imr;
+       int                     ret = IRQ_NONE;
+
+       do {
+               imr = dma_readl(atdma, EBCIMR);
+               status = dma_readl(atdma, EBCISR);
+               pending = status & imr;
+
+               if (!pending)
+                       break;
+
+               dev_vdbg(atdma->dma_common.dev,
+                       "interrupt: status = 0x%08x, 0x%08x, 0x%08x\n",

drivers/dma/at_hdmac.c line 447

Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+                        status, imr, pending);
+
+               for (i = 0; i < atdma->dma_common.chancnt; i++) {
+                       atchan = &atdma->chan[i];
+                       if (pending & (AT_DMA_CBTC(i) | AT_DMA_ERR(i))) {
+                               if (pending & AT_DMA_ERR(i)) {
+                                       /*
+                                       spin_lock(atchan->lock);
+                                       atchan->error_status = 1;
+                                       spin_unlock(atchan->lock);

writing to an unsigned long should already be atomic, no?

Quoted 252 lines
drivers/dma/at_hdmac.c new file +252 -0
+                                       */
+                                       /* Disable channel on AHB error */
+                                       dma_writel(atdma, CHDR, atchan->mask);
+                                       /* Give information to tasklet */
+                                       set_bit(0, &atchan->error_status);
+                               }
+                               tasklet_schedule(&atchan->tasklet);
+                               ret = IRQ_HANDLED;
+                       }
+               }
+
+       } while (pending);
+
+       return ret;
+}
+
+
+/*--  DMA Engine API  --------------------------------------------------*/
+
+/**
+ * atc_tx_submit - set the prepared descriptor(s) to be executed by the engine
+ * @desc: descriptor at the head of the transaction chain
+ *
+ * Queue chain if DMA engine is working already
+ *
+ * Cookie increment and adding to active_list or queue must be atomic
+ */
+static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+       struct at_desc          *desc = txd_to_at_desc(tx);
+       struct at_dma_chan      *atchan = to_at_dma_chan(tx->chan);
+       dma_cookie_t            cookie;
+
+       spin_lock_bh(&atchan->lock);
+       cookie = atc_assign_cookie(atchan, desc);
+
+       if (list_empty(&atchan->active_list)) {
+               dev_vdbg(&tx->chan->dev, "tx_submit: started %u\n",
+                               desc->txd.cookie);
+               atc_dostart(atchan, desc);
+               list_add_tail(&desc->desc_node, &atchan->active_list);
+       } else {
+               dev_vdbg(&tx->chan->dev, "tx_submit: queued %u\n",
+                               desc->txd.cookie);
+               list_add_tail(&desc->desc_node, &atchan->queue);
+       }
+
+       spin_unlock_bh(&atchan->lock);
+
+       return cookie;
+}
+
+/**
+ * atc_prep_dma_memcpy - prepare a memcpy operation
+ * @chan: the channel to prepare operation on
+ * @dest: operation virtual destination address
+ * @src: operation virtual source address
+ * @len: operation length
+ * @flags: tx descriptor status flags
+ */
+static struct dma_async_tx_descriptor *
+atc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
+               size_t len, unsigned long flags)
+{
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+       struct at_desc          *desc = NULL;
+       struct at_desc          *first = NULL;
+       struct at_desc          *prev = NULL;
+       size_t                  xfer_count;
+       size_t                  offset;
+       unsigned int            src_width;
+       unsigned int            dst_width;
+       u32                     ctrla;
+       u32                     ctrlb;
+
+       dev_vdbg(&chan->dev, "prep_dma_memcpy: d0x%x s0x%x l0x%zx f0x%lx\n",
+                       dest, src, len, flags);
+
+       if (unlikely(!len)) {
+               dev_dbg(&chan->dev, "prep_dma_memcpy: length is zero!\n");
+               return NULL;
+       }
+
+       ctrla =   ATC_DEFAULT_CTRLA;
+       ctrlb =   ATC_DEFAULT_CTRLB
+               | ATC_SRC_ADDR_MODE_INCR
+               | ATC_DST_ADDR_MODE_INCR
+               | ATC_FC_MEM2MEM;
+
+       /*
+        * We can be a lot more clever here, but this should take care
+        * of the most common optimization.
+        */
+       if (!((src | dest  | len) & 3)) {
+               ctrla |= ATC_SRC_WIDTH_WORD | ATC_DST_WIDTH_WORD;
+               src_width = dst_width = 2;
+       } else if (!((src | dest | len) & 1)) {
+               ctrla |= ATC_SRC_WIDTH_HALFWORD | ATC_DST_WIDTH_HALFWORD;
+               src_width = dst_width = 1;
+       } else {
+               ctrla |= ATC_SRC_WIDTH_BYTE | ATC_DST_WIDTH_BYTE;
+               src_width = dst_width = 0;
+       }
+
+       for (offset = 0; offset < len; offset += xfer_count << src_width) {
+               xfer_count = min_t(size_t, (len - offset) >> src_width,
+                               ATC_BTSIZE_MAX);
+
+               desc = atc_desc_get(atchan);
+               if (!desc)
+                       goto err_desc_get;
+
+               desc->lli.saddr = src + offset;
+               desc->lli.daddr = dest + offset;
+               desc->lli.ctrla = ctrla | xfer_count;
+               desc->lli.ctrlb = ctrlb;
+
+               desc->txd.cookie = 0;
+               async_tx_ack(&desc->txd);
+
+               if (!first) {
+                       first = desc;
+               } else {
+                       /* inform the HW lli about chaining */
+                       prev->lli.dscr = desc->txd.phys;
+                       /* insert the link descriptor to the LD ring */
+                       list_add_tail(&desc->desc_node,
+                                       &first->txd.tx_list);
+               }
+               prev = desc;
+       }
+
+       /* First descriptor of the chain embedds additional information */
+       first->txd.flags = flags; /* client is in control of this ack */
+       first->txd.cookie = -EBUSY;
+       first->len = len;
+
+       /* set end-of-link to the last link descriptor of list*/
+       set_desc_eol(desc);
+
+       return &first->txd;
+
+err_desc_get:
+       atc_desc_put(atchan, first);
+       return NULL;
+}
+
+/**
+ * atc_is_tx_complete - poll for transaction completion
+ * @chan: DMA channel
+ * @cookie: transaction identifier to check status of
+ * @done: if not %NULL, updated with last completed transaction
+ * @used: if not %NULL, updated with last used transaction
+ *
+ * If @done and @used are passed in, upon return they reflect the driver
+ * internal state and can be used with dma_async_is_complete() to check
+ * the status of multiple cookies without re-checking hardware state.
+ */
+static enum dma_status
+atc_is_tx_complete(struct dma_chan *chan,
+               dma_cookie_t cookie,
+               dma_cookie_t *done, dma_cookie_t *used)
+{
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+       dma_cookie_t            last_used;
+       dma_cookie_t            last_complete;
+       enum dma_status         ret;
+
+       dev_vdbg(&chan->dev, "is_tx_complete: %d (d%d, u%d)\n",
+                       cookie, done ? *done : 0, used ? *used : 0);
+
+       spin_lock_bh(atchan->lock);
+
+       last_complete = atchan->completed_cookie;
+       last_used = chan->cookie;
+
+       ret = dma_async_is_complete(cookie, last_complete, last_used);
+       if (ret != DMA_SUCCESS) {
+               atc_cleanup_descriptors(atchan);
+
+               last_complete = atchan->completed_cookie;
+               last_used = chan->cookie;
+
+               ret = dma_async_is_complete(cookie, last_complete, last_used);
+       }
+
+       spin_unlock_bh(atchan->lock);
+
+       if (done)
+               *done = last_complete;
+       if (used)
+               *used = last_used;
+
+       return ret;
+}
+
+/**
+ * atc_issue_pending - try to finish work
+ * @chan: target DMA channel
+ */
+static void atc_issue_pending(struct dma_chan *chan)
+{
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+
+       dev_vdbg(&chan->dev, "issue_pending\n");
+
+       if (!atc_chan_is_enabled(atchan)) {
+               spin_lock_bh(&atchan->lock);
+               atc_advance_work(atchan);
+               spin_unlock_bh(&atchan->lock);
+       }
+}
+
+/**
+ * atc_alloc_chan_resources - allocate resources for DMA channel
+ * @chan: allocate descriptor resources for this channel
+ * @client: current client requesting the channel be ready for requests
+ *
+ * return - the number of allocated descriptors
+ */
+static int atc_alloc_chan_resources(struct dma_chan *chan,
+                                   struct dma_client *client)
+{
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+       struct at_dma           *atdma = to_at_dma(chan->device);
+       struct at_desc          *desc;
+       int                     i;
+       LIST_HEAD(tmp_list);
+
+       dev_vdbg(&chan->dev, "alloc_chan_resources\n");
+
+       /* ASSERT:  channel is idle */
+       if (atc_chan_is_enabled(atchan)) {
+               dev_dbg(&chan->dev, "DMA channel not idle ?\n");
+               return -EIO;
+       }
+
+       /* have we already been set up? */
+       if (!list_empty(&atchan->free_list))
+               return atchan->descs_allocated;
+
+       /* Allocate initial pool of descriptors */
+       for (i = 0; i < INIT_NR_DESCS_PER_CHANNEL; i++) {
+               desc = atc_alloc_descriptor(chan, GFP_KERNEL);
+               if (!desc) {
+                       dev_err(atdma->dma_common.dev,
+                               "Only %d initial descriptors\n", i);
+                       break;
+               }
+               list_add_tail(&desc->desc_node, &tmp_list);
+       }
+

drivers/dma/at_hdmac.c line 709

Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+       spin_lock_bh(&atchan->lock);
+       atchan->descs_allocated = i;
+       list_splice(&tmp_list, &atchan->free_list);
+       atchan->completed_cookie = chan->cookie = 1;
+       spin_unlock_bh(&atchan->lock);
+
+       /* channel parameters */
+       channel_writel(atchan, CFG, ATC_DEFAULT_CFG);
+
+       tasklet_init(&atchan->tasklet, atc_tasklet, (unsigned long)atchan);

This routine may be called while the channel is already active, potentially causing tasklet_init() to be called while a tasklet is pending. Can this move to at_dma_probe()?

drivers/dma/at_hdmac.c line 713

Quoted 4 lines
drivers/dma/at_hdmac.c new file +4 -0
+       /* clear any pending interrupt */
+       while (dma_readl(atdma, EBCISR))
+               cpu_relax();
+       atc_enable_irq(atchan);

ditto.

Quoted 698 lines
drivers/dma/at_hdmac.c new file +276 -0
+
+       dev_dbg(&chan->dev,
+               "alloc_chan_resources: allocated %d descriptors\n",
+               atchan->descs_allocated);
+
+       return atchan->descs_allocated;
+}
+
+/**
+ * atc_free_chan_resources - free all channel resources
+ * @chan: DMA channel
+ */
+static void atc_free_chan_resources(struct dma_chan *chan)
+{
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+       struct at_dma           *atdma = to_at_dma(chan->device);
+       struct at_desc          *desc, *_desc;
+       LIST_HEAD(list);
+
+       dev_dbg(&chan->dev, "free_chan_resources: (descs allocated=%u)\n",
+                       atchan->descs_allocated);
+
+       /* ASSERT:  channel is idle */
+       BUG_ON(!list_empty(&atchan->active_list));
+       BUG_ON(!list_empty(&atchan->queue));
+       BUG_ON(atc_chan_is_enabled(atchan));
+
+       /* Disable interrupts */
+       atc_disable_irq(atchan);
+       tasklet_disable(&atchan->tasklet);
+
+       list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) {
+               dev_vdbg(&chan->dev, "  freeing descriptor %p\n", desc);
+               list_del(&desc->desc_node);
+               /* free link descriptor */
+               dma_pool_free(atdma->dma_desc_pool, desc, desc->txd.phys);
+       }
+       list_splice_init(&atchan->free_list, &list);
+       atchan->descs_allocated = 0;
+
+       dev_vdbg(&chan->dev, "free_chan_resources: done\n");
+}
+
+
+/*--  Module Management  -----------------------------------------------*/
+
+/**
+ * at_dma_off - disable DMA controller
+ * @atdma: the Atmel HDAMC device
+ */
+static void at_dma_off(struct at_dma *atdma)
+{
+       dma_writel(atdma, EN, 0);
+
+       /* disable all interrupts */
+       dma_writel(atdma, EBCIDR, -1L);
+
+       /* confirm that all channels are disabled */
+       while (dma_readl(atdma, CHSR) & atdma->all_chan_mask)
+               cpu_relax();
+}
+
+static int __init at_dma_probe(struct platform_device *pdev)
+{
+       struct at_dma_platform_data *pdata;
+       struct resource         *io;
+       struct at_dma           *atdma;
+       size_t                  size;
+       int                     irq;
+       int                     err;
+       int                     i;
+
+       /* get DMA Controller parameters from platform */
+       pdata = pdev->dev.platform_data;
+       if (!pdata || pdata->nr_channels > AT_DMA_MAX_NR_CHANNELS)
+               return -EINVAL;
+
+       io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+       if (!io)
+               return -EINVAL;
+
+       irq = platform_get_irq(pdev, 0);
+       if (irq < 0)
+               return irq;
+
+       size = sizeof(struct at_dma);
+       size += pdata->nr_channels * sizeof(struct at_dma_chan);
+       atdma = kzalloc(size, GFP_KERNEL);
+       if (!atdma)
+               return -ENOMEM;
+
+       /* discover transaction capabilites from the platform data */
+       atdma->dma_common.cap_mask = pdata->cap_mask;
+       atdma->all_chan_mask = (1 << pdata->nr_channels) - 1;
+
+       size = io->end - io->start + 1;
+       if (!request_mem_region(io->start, size, pdev->dev.driver->name)) {
+               err = -EBUSY;
+               goto err_kfree;
+       }
+
+       atdma->regs = ioremap(io->start, size);
+       if (!atdma->regs) {
+               err = -ENOMEM;
+               goto err_release_r;
+       }
+
+       atdma->clk = clk_get(&pdev->dev, "dma_clk");
+       if (IS_ERR(atdma->clk)) {
+               err = PTR_ERR(atdma->clk);
+               goto err_clk;
+       }
+       clk_enable(atdma->clk);
+
+       /* force dma off, just in case */
+       at_dma_off(atdma);
+
+       err = request_irq(irq, at_dma_interrupt, 0, "at_hdmac", atdma);
+       if (err)
+               goto err_irq;
+
+       platform_set_drvdata(pdev, atdma);
+
+       /* creates a pool of consistent memory blocks for hardware descriptors */
+       atdma->dma_desc_pool = dma_pool_create("at_hdmac_desc_pool",
+                       &pdev->dev, sizeof(struct at_desc),
+                       4 /* word alignment */, 0);
+       if (!atdma->dma_desc_pool) {
+               dev_err(&pdev->dev, "No memory for descriptors dma pool\n");
+               err = -ENOMEM;
+               goto err_pool_create;
+       }
+
+       /* initialize channels related values */
+       INIT_LIST_HEAD(&atdma->dma_common.channels);
+       for (i = 0; i < pdata->nr_channels; i++, atdma->dma_common.chancnt++) {
+               struct at_dma_chan      *atchan = &atdma->chan[i];
+
+               atchan->chan_common.device = &atdma->dma_common;
+               atchan->chan_common.cookie = atchan->completed_cookie = 1;
+               atchan->chan_common.chan_id = i;
+               list_add_tail(&atchan->chan_common.device_node, &atdma->dma_common.channels);
+
+               atchan->ch_regs = atdma->regs + ch_regs(i);
+               spin_lock_init(&atchan->lock);
+               atchan->mask = 1 << i;
+
+               INIT_LIST_HEAD(&atchan->active_list);
+               INIT_LIST_HEAD(&atchan->queue);
+               INIT_LIST_HEAD(&atchan->free_list);
+       }
+
+       /* set base routines */
+       atdma->dma_common.device_alloc_chan_resources = atc_alloc_chan_resources;
+       atdma->dma_common.device_free_chan_resources = atc_free_chan_resources;
+       atdma->dma_common.device_is_tx_complete = atc_is_tx_complete;
+       atdma->dma_common.device_issue_pending = atc_issue_pending;
+       atdma->dma_common.dev = &pdev->dev;
+
+       /* set prep routines based on capability */
+       if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask))
+               atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy;
+
+       dma_writel(atdma, EN, AT_DMA_ENABLE);
+
+       dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n",
+         dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask) ? "cpy " : "",
+         dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)  ? "slave " : "",
+         atdma->dma_common.chancnt);
+
+       dma_async_device_register(&atdma->dma_common);
+
+       return 0;
+
+err_pool_create:
+       platform_set_drvdata(pdev, NULL);
+       free_irq(platform_get_irq(pdev, 0), atdma);
+err_irq:
+       clk_disable(atdma->clk);
+       clk_put(atdma->clk);
+err_clk:
+       iounmap(atdma->regs);
+       atdma->regs = NULL;
+err_release_r:
+       release_mem_region(io->start, size);
+err_kfree:
+       kfree(atdma);
+       return err;
+}
+
+static int __exit at_dma_remove(struct platform_device *pdev)
+{
+       struct at_dma           *atdma = platform_get_drvdata(pdev);
+       struct dma_chan         *chan, *_chan;
+       struct resource         *io;
+
+       at_dma_off(atdma);
+       dma_async_device_unregister(&atdma->dma_common);
+
+       dma_pool_destroy(atdma->dma_desc_pool);
+       platform_set_drvdata(pdev, NULL);
+       free_irq(platform_get_irq(pdev, 0), atdma);
+
+       list_for_each_entry_safe(chan, _chan, &atdma->dma_common.channels,
+                       device_node) {
+               tasklet_kill(&(to_at_dma_chan(chan)->tasklet));
+               list_del(&chan->device_node);
+       }
+
+       clk_disable(atdma->clk);
+       clk_put(atdma->clk);
+
+       iounmap(atdma->regs);
+       atdma->regs = NULL;
+
+       io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+       release_mem_region(io->start, io->end - io->start + 1);
+
+       kfree(atdma);
+
+       return 0;
+}
+
+static void at_dma_shutdown(struct platform_device *pdev)
+{
+       struct at_dma   *atdma = platform_get_drvdata(pdev);
+
+       at_dma_off(platform_get_drvdata(pdev));
+       clk_disable(atdma->clk);
+}
+
+static int at_dma_suspend_late(struct platform_device *pdev, pm_message_t mesg)
+{
+       struct at_dma   *atdma = platform_get_drvdata(pdev);
+
+       at_dma_off(platform_get_drvdata(pdev));
+       clk_disable(atdma->clk);
+       return 0;
+}
+
+static int at_dma_resume_early(struct platform_device *pdev)
+{
+       struct at_dma   *atdma = platform_get_drvdata(pdev);
+
+       clk_enable(atdma->clk);
+       dma_writel(atdma, EN, AT_DMA_ENABLE);
+       return 0;
+
+}
+
+static struct platform_driver at_dma_driver = {
+       .remove         = __exit_p(at_dma_remove),
+       .shutdown       = at_dma_shutdown,
+       .suspend_late   = at_dma_suspend_late,
+       .resume_early   = at_dma_resume_early,
+       .driver = {
+               .name   = "at_hdmac",
+       },
+};
+
+static int __init at_dma_init(void)
+{
+       return platform_driver_probe(&at_dma_driver, at_dma_probe);
+}
+module_init(at_dma_init);
+
+static void __exit at_dma_exit(void)
+{
+       platform_driver_unregister(&at_dma_driver);
+}
+module_exit(at_dma_exit);
+
+MODULE_DESCRIPTION("Atmel AHB DMA Controller driver");
+MODULE_AUTHOR("Nicolas Ferre <[email protected]>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:at_hdmac");
drivers/dma/at_hdmac_regs.h new file +377 -0
new file mode 100644
index 0000000..294f625
@@ -0,0 +1,377 @@
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_REGS_H
+#define        AT_HDMAC_REGS_H
+
+#include <linux/at_hdmac.h>
+
+#define        AT_DMA_MAX_NR_CHANNELS  8
+
+
+#define        AT_DMA_GCFG     0x00    /* Global Configuration Register */
+#define                AT_DMA_IF_BIGEND(i)     (0x1 << (i))    /* AHB-Lite Interface i in Big-endian mode */
+#define                AT_DMA_ARB_CFG  (0x1 << 4)      /* Arbiter mode. */
+#define                        AT_DMA_ARB_CFG_FIXED            (0x0 << 4)
+#define                        AT_DMA_ARB_CFG_ROUND_ROBIN      (0x1 << 4)
+
+#define        AT_DMA_EN       0x04    /* Controller Enable Register */
+#define                AT_DMA_ENABLE   (0x1 << 0)
+
+#define        AT_DMA_SREQ     0x08    /* Software Single Request Register */
+#define                AT_DMA_SSREQ(x) (0x1 << ((x) << 1))             /* Request a source single transfer on channel x */
+#define                AT_DMA_DSREQ(x) (0x1 << (1 + ((x) << 1)))       /* Request a destination single transfer on channel x */
+
+#define        AT_DMA_CREQ     0x0C    /* Software Chunk Transfer Request Register */
+#define                AT_DMA_SCREQ(x) (0x1 << ((x) << 1))             /* Request a source chunk transfer on channel x */
+#define                AT_DMA_DCREQ(x) (0x1 << (1 + ((x) << 1)))       /* Request a destination chunk transfer on channel x */
+
+#define        AT_DMA_LAST     0x10    /* Software Last Transfer Flag Register */
+#define                AT_DMA_SLAST(x) (0x1 << ((x) << 1))             /* This src rq is last tx of buffer on channel x */
+#define                AT_DMA_DLAST(x) (0x1 << (1 + ((x) << 1)))       /* This dst rq is last tx of buffer on channel x */
+
+#define        AT_DMA_SYNC     0x14    /* Request Synchronization Register */
+#define                AT_DMA_SYR(h)   (0x1 << (h))                    /* Synchronize handshake line h */
+
+/* Error, Chained Buffer transfer completed and Buffer transfer completed Interrupt registers */
+#define        AT_DMA_EBCIER   0x18    /* Enable register */
+#define        AT_DMA_EBCIDR   0x1C    /* Disable register */
+#define        AT_DMA_EBCIMR   0x20    /* Mask Register */
+#define        AT_DMA_EBCISR   0x24    /* Status Register */
+#define                AT_DMA_CBTC_OFFSET      8
+#define                AT_DMA_ERR_OFFSET       16
+#define                AT_DMA_BTC(x)   (0x1 << (x))
+#define                AT_DMA_CBTC(x)  (0x1 << (AT_DMA_CBTC_OFFSET + (x)))
+#define                AT_DMA_ERR(x)   (0x1 << (AT_DMA_ERR_OFFSET + (x)))
+
+#define        AT_DMA_CHER     0x28    /* Channel Handler Enable Register */
+#define                AT_DMA_ENA(x)   (0x1 << (x))
+#define                AT_DMA_SUSP(x)  (0x1 << ( 8 + (x)))
+#define                AT_DMA_KEEP(x)  (0x1 << (24 + (x)))
+
+#define        AT_DMA_CHDR     0x2C    /* Channel Handler Disable Register */
+#define                AT_DMA_DIS(x)   (0x1 << (x))
+#define                AT_DMA_RES(x)   (0x1 << ( 8 + (x)))
+
+#define        AT_DMA_CHSR     0x30    /* Channel Handler Status Register */
+#define                AT_DMA_EMPT(x)  (0x1 << (16 + (x)))
+#define                AT_DMA_STAL(x)  (0x1 << (24 + (x)))
+
+
+#define        AT_DMA_CH_REGS_BASE     0x3C    /* Channel registers base address */
+#define        ch_regs(x)      (AT_DMA_CH_REGS_BASE + (x) * 0x28) /* Channel x base addr */
+
+/* Hardware register offset for each channel */
+#define        ATC_SADDR_OFFSET        0x00    /* Source Address Register */
+#define        ATC_DADDR_OFFSET        0x04    /* Destination Address Register */
+#define        ATC_DSCR_OFFSET         0x08    /* Descriptor Address Register */
+#define        ATC_CTRLA_OFFSET        0x0C    /* Control A Register */
+#define        ATC_CTRLB_OFFSET        0x10    /* Control B Register */
+#define        ATC_CFG_OFFSET          0x14    /* Configuration Register */
+#define        ATC_SPIP_OFFSET         0x18    /* Src PIP Configuration Register */
+#define        ATC_DPIP_OFFSET         0x1C    /* Dst PIP Configuration Register */
+
+
+/* Bitfield definitions */
+
+/* Bitfields in DSCR */
+#define        ATC_DSCR_IF(i)          (0x3 & (i))     /* Dsc feched via AHB-Lite Interface i */
+
+/* Bitfields in CTRLA */
+#define        ATC_BTSIZE_MAX          0xFFFFUL        /* Maximum Buffer Transfer Size */
+#define        ATC_BTSIZE(x)           (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */
+#define        ATC_SCSIZE_MASK         (0x7 << 16)     /* Source Chunk Transfer Size */
+#define                ATC_SCSIZE_1            (0x0 << 16)
+#define                ATC_SCSIZE_4            (0x1 << 16)
+#define                ATC_SCSIZE_8            (0x2 << 16)
+#define                ATC_SCSIZE_16           (0x3 << 16)
+#define                ATC_SCSIZE_32           (0x4 << 16)
+#define                ATC_SCSIZE_64           (0x5 << 16)
+#define                ATC_SCSIZE_128          (0x6 << 16)
+#define                ATC_SCSIZE_256          (0x7 << 16)
+#define        ATC_DCSIZE_MASK         (0x7 << 20)     /* Destination Chunk Transfer Size */
+#define                ATC_DCSIZE_1            (0x0 << 20)
+#define                ATC_DCSIZE_4            (0x1 << 20)
+#define                ATC_DCSIZE_8            (0x2 << 20)
+#define                ATC_DCSIZE_16           (0x3 << 20)
+#define                ATC_DCSIZE_32           (0x4 << 20)
+#define                ATC_DCSIZE_64           (0x5 << 20)
+#define                ATC_DCSIZE_128          (0x6 << 20)
+#define                ATC_DCSIZE_256          (0x7 << 20)
+#define        ATC_SRC_WIDTH_MASK      (0x3 << 24)     /* Source Single Transfer Size */
+#define                ATC_SRC_WIDTH_BYTE      (0x0 << 24)
+#define                ATC_SRC_WIDTH_HALFWORD  (0x1 << 24)
+#define                ATC_SRC_WIDTH_WORD      (0x2 << 24)
+#define        ATC_DST_WIDTH_MASK      (0x3 << 28)     /* Destination Single Transfer Size */
+#define                ATC_DST_WIDTH_BYTE      (0x0 << 28)
+#define                ATC_DST_WIDTH_HALFWORD  (0x1 << 28)
+#define                ATC_DST_WIDTH_WORD      (0x2 << 28)
+#define        ATC_DONE                (0x1 << 31)     /* Tx Done (only written back in descriptor) */
+
+/* Bitfields in CTRLB */
+#define        ATC_SIF(i)              (0x3 & (i))     /* Src tx done via AHB-Lite Interface i */
+#define        ATC_DIF(i)              ((0x3 & (i)) <<  4)     /* Dst tx done via AHB-Lite Interface i */
+#define        ATC_SRC_PIP             (0x1 <<  8)     /* Source Picture-in-Picture enabled */
+#define        ATC_DST_PIP             (0x1 << 12)     /* Destination Picture-in-Picture enabled */
+#define        ATC_SRC_DSCR_DIS        (0x1 << 16)     /* Src Descriptor fetch disable */
+#define        ATC_DST_DSCR_DIS        (0x1 << 20)     /* Dst Descriptor fetch disable */
+#define        ATC_FC_MASK             (0x7 << 21)     /* Choose Flow Controller */
+#define                ATC_FC_MEM2MEM          (0x0 << 21)     /* Mem-to-Mem (DMA) */
+#define                ATC_FC_MEM2PER          (0x1 << 21)     /* Mem-to-Periph (DMA) */
+#define                ATC_FC_PER2MEM          (0x2 << 21)     /* Periph-to-Mem (DMA) */
+#define                ATC_FC_PER2PER          (0x3 << 21)     /* Periph-to-Periph (DMA) */
+#define                ATC_FC_PER2MEM_PER      (0x4 << 21)     /* Periph-to-Mem (Peripheral) */
+#define                ATC_FC_MEM2PER_PER      (0x5 << 21)     /* Mem-to-Periph (Peripheral) */
+#define                ATC_FC_PER2PER_PER      (0x6 << 21)     /* Periph-to-Periph (Src Peripheral) */
+#define        ATC_SRC_ADDR_MODE_MASK  (0x3 << 24)
+#define                ATC_SRC_ADDR_MODE_INCR  (0x0 << 24)     /* Incrementing Mode */
+#define                ATC_SRC_ADDR_MODE_DECR  (0x1 << 24)     /* Decrementing Mode */
+#define                ATC_SRC_ADDR_MODE_FIXED (0x2 << 24)     /* Fixed Mode */
+#define        ATC_DST_ADDR_MODE_MASK  (0x3 << 28)
+#define                ATC_DST_ADDR_MODE_INCR  (0x0 << 28)     /* Incrementing Mode */
+#define                ATC_DST_ADDR_MODE_DECR  (0x1 << 28)     /* Decrementing Mode */
+#define                ATC_DST_ADDR_MODE_FIXED (0x2 << 28)     /* Fixed Mode */
+#define        ATC_IEN                 (0x1 << 30)     /* BTC interrupt enable (active low) */
+#define        ATC_AUTO                (0x1 << 31)     /* Auto multiple buffer tx enable */
+
+/* Bitfields in CFG */
+#define        ATC_SRC_PER(h)          (0xFU & (h))    /* Channel src rq associated with periph handshaking ifc h */
+#define        ATC_DST_PER(h)          ((0xFU & (h)) <<  4)    /* Channel dst rq associated with periph handshaking ifc h */
+#define        ATC_SRC_REP             (0x1 <<  8)     /* Source Replay Mod */
+#define        ATC_SRC_H2SEL           (0x1 <<  9)     /* Source Handshaking Mod */
+#define                ATC_SRC_H2SEL_SW        (0x0 <<  9)
+#define                ATC_SRC_H2SEL_HW        (0x1 <<  9)
+#define        ATC_DST_REP             (0x1 << 12)     /* Destination Replay Mod */
+#define        ATC_DST_H2SEL           (0x1 << 13)     /* Destination Handshaking Mod */
+#define                ATC_DST_H2SEL_SW        (0x0 << 13)
+#define                ATC_DST_H2SEL_HW        (0x1 << 13)
+#define        ATC_SOD                 (0x1 << 16)     /* Stop On Done */
+#define        ATC_LOCK_IF             (0x1 << 20)     /* Interface Lock */
+#define        ATC_LOCK_B              (0x1 << 21)     /* AHB Bus Lock */
+#define        ATC_LOCK_IF_L           (0x1 << 22)     /* Master Interface Arbiter Lock */
+#define                ATC_LOCK_IF_L_CHUNK     (0x0 << 22)
+#define                ATC_LOCK_IF_L_BUFFER    (0x1 << 22)
+#define        ATC_AHB_PROT_MASK       (0x7 << 24)     /* AHB Protection */
+#define        ATC_FIFOCFG_MASK        (0x3 << 28)     /* FIFO Request Configuration */
+#define                ATC_FIFOCFG_LARGESTBURST        (0x0 << 28)
+#define                ATC_FIFOCFG_HALFFIFO            (0x1 << 28)
+#define                ATC_FIFOCFG_ENOUGHSPACE         (0x2 << 28)
+
+/* Bitfields in SPIP */
+#define        ATC_SPIP_HOLE(x)        (0xFFFFU & (x))
+#define        ATC_SPIP_BOUNDARY(x)    ((0x3FF & (x)) << 16)
+
+/* Bitfields in DPIP */
+#define        ATC_DPIP_HOLE(x)        (0xFFFFU & (x))
+#define        ATC_DPIP_BOUNDARY(x)    ((0x3FF & (x)) << 16)
+
+
+/*--  descriptors  -----------------------------------------------------*/
+
+/* LLI == Linked List Item; aka DMA buffer descriptor */
+struct at_lli {
+       /* values that are not changed by hardware */
+       dma_addr_t      saddr;
+       dma_addr_t      daddr;
+       /* value that may get written back: */
+       u32             ctrla;
+       /* more values that are not changed by hardware */
+       u32             ctrlb;
+       dma_addr_t      dscr;   /* chain to next lli */
+};
+
+/**
+ * struct at_desc - software descriptor
+ * @at_lli: hardware lli structure
+ * @txd: support for the async_tx api
+ * @desc_node: node on the channed descriptors list
+ * @len: total transaction bytecount
+ */
+struct at_desc {
+       /* FIRST values the hardware uses */
+       struct at_lli                   lli;
+
+       /* THEN values for driver housekeeping */
+       struct dma_async_tx_descriptor  txd;
+       struct list_head                desc_node;
+       size_t                          len;
+};
+
+static inline struct at_desc *
+txd_to_at_desc(struct dma_async_tx_descriptor *txd)
+{
+       return container_of(txd, struct at_desc, txd);
+}
+
+
+/*--  Channels  --------------------------------------------------------*/
+
+/**
+ * struct at_dma_chan - internal representation of an Atmel HDMAC channel
+ * @chan_common: common dmaengine channel object members
+ * @device: parent device
+ * @ch_regs: memory mapped register base
+ * @mask: channel index in a mask
+ * @error_status: transmit error status information from irq handler
+ *                to tasklet (use atomic operations)
+ * @tasklet: bottom half to finish transaction work
+ * @lock: serializes enqueue/dequeue operations to descriptors lists
+ * @completed_cookie: identifier for the most recently completed operation
+ * @active_list: list of descriptors dmaengine is being running on
+ * @queue: list of descriptors ready to be submitted to engine
+ * @free_list: list of descriptors usable by the channel
+ * @descs_allocated: records the actual size of the descriptor pool
+ */
+struct at_dma_chan {
+       struct dma_chan         chan_common;
+       struct at_dma           *device;
+       void __iomem            *ch_regs;
+       u8                      mask;
+       unsigned long           error_status;
+       struct tasklet_struct   tasklet;
+
+       spinlock_t              lock;
+
+       /* these other elements are all protected by lock */
+       dma_cookie_t            completed_cookie;
+       struct list_head        active_list;
+       struct list_head        queue;
+       struct list_head        free_list;
+       unsigned int            descs_allocated;
+};
+
+#define        channel_readl(atchan, name) \
+       __raw_readl((atchan)->ch_regs + ATC_##name##_OFFSET)
+
+#define        channel_writel(atchan, name, val) \
+       __raw_writel((val), (atchan)->ch_regs + ATC_##name##_OFFSET)
+
+static inline struct at_dma_chan *to_at_dma_chan(struct dma_chan *dchan)
+{
+       return container_of(dchan, struct at_dma_chan, chan_common);
+}
+
+
+/*--  Controller  ------------------------------------------------------*/
+
+/**
+ * struct at_dma - internal representation of an Atmel HDMA Controller
+ * @chan_common: common dmaengine dma_device object members
+ * @ch_regs: memory mapped register base
+ * @clk: dma controller clock
+ * @all_chan_mask: all channels availlable in a mask
+ * @dma_desc_pool: base of DMA descriptor region (DMA address)
+ * @chan: channels table to store at_dma_chan structures
+ */
+struct at_dma {
+       struct dma_device       dma_common;
+       void __iomem            *regs;
+       struct clk              *clk;
+
+       u8                      all_chan_mask;
+
+       struct dma_pool         *dma_desc_pool;
+       /* AT THE END channels table */
+       struct at_dma_chan      chan[0];
+};
+
+#define        dma_readl(atdma, name) \
+       __raw_readl((atdma)->regs + AT_DMA_##name)
+#define        dma_writel(atdma, name, val) \
+       __raw_writel((val), (atdma)->regs + AT_DMA_##name)
+
+static inline struct at_dma *to_at_dma(struct dma_device *ddev)
+{
+       return container_of(ddev, struct at_dma, dma_common);
+}
+
+
+/*--  Helper functions  ------------------------------------------------*/
+
+#if defined(VERBOSE_DEBUG)
+static void vdbg_dump_regs(struct at_dma_chan *atchan)
+{
+       struct at_dma   *atdma = to_at_dma(atchan->chan_common.device);
+
+       dev_err(&atchan->chan_common.dev,
+               "  channel %d : imr = 0x%x, chsr = 0x%x\n",
+               atchan->chan_common.chan_id,
+               dma_readl(atdma, EBCIMR),
+               dma_readl(atdma, CHSR));
+
+       dev_err(&atchan->chan_common.dev,
+               "  channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+               channel_readl(atchan, SADDR),
+               channel_readl(atchan, DADDR),
+               channel_readl(atchan, CTRLA),
+               channel_readl(atchan, CTRLB),
+               channel_readl(atchan, DSCR));
+}
+#else
+static void vdbg_dump_regs(struct at_dma_chan *atchan) {}
+#endif
+
+static void atc_dump_lli(struct at_dma_chan *atchan, struct at_lli *lli)
+{
+       dev_printk(KERN_CRIT, &atchan->chan_common.dev,
+                       "  desc: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+                       lli->saddr, lli->daddr,
+                       lli->ctrla, lli->ctrlb, lli->dscr);
+}
+
+
+static void atc_setup_irq(struct at_dma_chan *atchan, int on)
+{
+       struct at_dma   *atdma = to_at_dma(atchan->chan_common.device);
+       u32             ebci;
+
+       /* enable interrupts on buffer chain completion & error */
+       ebci =    AT_DMA_CBTC(atchan->chan_common.chan_id)
+               | AT_DMA_ERR(atchan->chan_common.chan_id);
+       if (on)
+               dma_writel(atdma, EBCIER, ebci);
+       else
+               dma_writel(atdma, EBCIDR, ebci);
+}
+
+static inline void atc_enable_irq(struct at_dma_chan *atchan)
+{
+       atc_setup_irq(atchan, 1);
+}
+
+static inline void atc_disable_irq(struct at_dma_chan *atchan)
+{
+       atc_setup_irq(atchan, 0);
+}
+
+
+/**
+ * atc_chan_is_enabled - test if given channel is enabled
+ * @atchan: channel we want to test status
+ */
+static inline int atc_chan_is_enabled(struct at_dma_chan *atchan)
+{
+       struct at_dma   *atdma = to_at_dma(atchan->chan_common.device);
+
+       return !!(dma_readl(atdma, CHSR) & atchan->mask);
+}
+
+
+/**
+ * set_desc_eol - set end-of-link to descriptor so it will end transfer
+ * @desc: descriptor, signle or at the end of a chain, to end chain on
+ */
+static void set_desc_eol(struct at_desc *desc)
+{
+       desc->lli.ctrlb |= ATC_SRC_DSCR_DIS | ATC_DST_DSCR_DIS;
+       desc->lli.dscr = 0;
+}
+
+#endif /* AT_HDMAC_REGS_H */
include/linux/at_hdmac.h new file +26 -1
new file mode 100644
index 0000000..21a5554
@@ -0,0 +1,26 @@
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_H
+#define AT_HDMAC_H
+
+#include <linux/dmaengine.h>
+
+/**
+ * struct at_dma_platform_data - Controller configuration parameters
+ * @nr_channels: Number of channels supported by hardware (max 8)
+ * @cap_mask: dma_capability flags supported by the platform
+ */
+struct at_dma_platform_data {
+       unsigned int    nr_channels;
+       dma_cap_mask_t  cap_mask;
+};
+
+#endif /* AT_HDMAC_H */
--

1.5.3.7

Acked-by on v1 1/1
#6 lore raw
In reply to Nicolas Ferre
Quoted 15 lines · Nicolas Ferre

This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip.
On other products, it will be used also for peripheral DMA transfer (slave API
support to come).

I used dmatest client without problem in different configurations to test
it.

Quoted 6 lines

Full documentation for this controller can be found in the SAM9RL datasheet :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

---

Hi Nicolas,
I have walked through the code and I do not see any serious problems here.

#7 lore raw

Sosnowski, Maciej :

Quoted 16 lines
Quoted 15 lines · Nicolas Ferre

This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip.
On other products, it will be used also for peripheral DMA transfer (slave API support to come).

I used dmatest client without problem in different configurations to test it.

Full documentation for this controller can be found in the SAM9RL datasheet :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

Quoted 6 lines
Quoted 2 lines

---

Hi Nicolas,
I have walked through the code and I do not see any serious problems here.

Great !
Thanks for your feedback.

Quoted 2 lines

Kind regards,

Signature · 1 line
Nicolas Ferre
#2 lore raw
In reply to Dan Williams

Hi Dan,

Thanks a lot for your feedback.

Dan Williams :

Quoted 20 lines · Nicolas Ferre
Quoted 8 lines

This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip.
On other products, it will be used also for peripheral DMA transfer (slave API support to come).

Quoted 8 lines

I used dmatest client without problem in different configurations to test it.

Full documentation for this controller can be found in the SAM9RL datasheet :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

---

Hi Nicolas,

Quoted 7 lines

A few comments below.

Also, checkpatch reported:

total: 4 errors, 45 warnings, 1475 lines checked

...mostly 80 column warnings (some you may want to take a look at).

I reviewed this and manage to reduce most of 80 column warnings. An error remains but it is a space in "if" statement and it is for alignment purpose.

Quoted 11 lines

Regards,
Dan

Quoted 6 lines
 arch/arm/mach-at91/at91sam9rl_devices.c |   47 ++
 drivers/dma/Kconfig                     |    8 +
 drivers/dma/Makefile                    |    1 +
 drivers/dma/at_hdmac.c                  |  989 +++++++++++++++++++++++++++++++
 drivers/dma/at_hdmac_regs.h             |  377 ++++++++++++
 include/linux/at_hdmac.h                |   26 +

...this header should be moved somewhere under arch/arm/include.

This is where dw_dmac.h resides. Moreover, if one day this IP is implemented on a different architecture, it will be good not to reach it through arch/arm path.

[..]

Quoted 10 lines
Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+/**
+ * atc_alloc_descriptor - allocate and return an initilized descriptor
+ * @chan: the channel to allocate descriptors for
+ * @gfp_flags: GFP allocation flags
+ */
+static struct at_desc *atc_alloc_descriptor(struct dma_chan *chan,
+                                           gfp_t gfp_flags)
+{
+       struct at_desc  *desc = NULL;
+       struct at_dma   *atdma = to_at_dma(chan->device);
Quoted 8 lines

drivers/dma/at_hdmac.c line 78

Quoted 5 lines
drivers/dma/at_hdmac.c new file +5 -0
+       dma_addr_t phys;
+
+       desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys);
+       if (desc) {
+               BUG_ON(phys & 0x3UL); /* descriptors have to be word aligned */

hmm, yes this is a bug but can't we trust that dma_pool_alloc does its job correctly?

Indeed, it was mainly for debugging purpose, I remove it.

Quoted 7 lines

drivers/dma/at_hdmac.c line 81

Quoted 3 lines
drivers/dma/at_hdmac.c new file +3 -0
+               memset(desc, 0, sizeof(struct at_desc));
+               dma_async_tx_descriptor_init(&desc->txd, chan);
+               async_tx_ack(&desc->txd);

the DMA_CTRL_ACK bit is under control of the client. It should be read-only to the driver (except for extra descriptors that the driver creates on behalf of the client).

This is precisely where the descriptors are been created so, I thought it should be ok to initialize this bit. Am I right ?

[..]

Quoted 22 lines
Quoted 22 lines
drivers/dma/at_hdmac.c new file +22 -0
+static irqreturn_t at_dma_interrupt(int irq, void *dev_id)
+{
+       struct at_dma           *atdma = (struct at_dma *)dev_id;
+       struct at_dma_chan      *atchan;
+       int                     i;
+       u32                     status, pending, imr;
+       int                     ret = IRQ_NONE;
+
+       do {
+               imr = dma_readl(atdma, EBCIMR);
+               status = dma_readl(atdma, EBCISR);
+               pending = status & imr;
+
+               if (!pending)
+                       break;
+
+               dev_vdbg(atdma->dma_common.dev,
+                       "interrupt: status = 0x%08x, 0x%08x, 0x%08x\n",
+                        status, imr, pending);
+
+               for (i = 0; i < atdma->dma_common.chancnt; i++) {
+                       atchan = &atdma->chan[i];
Quoted 8 lines

drivers/dma/at_hdmac.c line 447

Quoted 6 lines
drivers/dma/at_hdmac.c new file +6 -0
+                       if (pending & (AT_DMA_CBTC(i) | AT_DMA_ERR(i))) {
+                               if (pending & AT_DMA_ERR(i)) {
+                                       /*
+                                       spin_lock(atchan->lock);
+                                       atchan->error_status = 1;
+                                       spin_unlock(atchan->lock);

writing to an unsigned long should already be atomic, no?

On ARM yes, on other architectures, I do not know... Anyway, I removed those commented lines.

[..]

Quoted 10 lines
Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+/**
+ * atc_alloc_chan_resources - allocate resources for DMA channel
+ * @chan: allocate descriptor resources for this channel
+ * @client: current client requesting the channel be ready for requests
+ *
+ * return - the number of allocated descriptors
+ */
+static int atc_alloc_chan_resources(struct dma_chan *chan,
+                                   struct dma_client *client)
+{
Quoted 8 lines

drivers/dma/at_hdmac.c line 678

Quoted 8 lines
drivers/dma/at_hdmac.c new file +8 -0
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+       struct at_dma           *atdma = to_at_dma(chan->device);
+       struct at_desc          *desc;
+       int                     i;
+       LIST_HEAD(tmp_list);
+
+       dev_vdbg(&chan->dev, "alloc_chan_resources\n");
+

[TAG]

Quoted 5 lines

drivers/dma/at_hdmac.c line 683

Quoted 5 lines
drivers/dma/at_hdmac.c new file +5 -0
+       /* ASSERT:  channel is idle */
+       if (atc_chan_is_enabled(atchan)) {
+               dev_dbg(&chan->dev, "DMA channel not idle ?\n");
+               return -EIO;
+       }

[/TAG]

Quoted 22 lines
Quoted 22 lines
drivers/dma/at_hdmac.c new file +22 -0
+
+       /* have we already been set up? */
+       if (!list_empty(&atchan->free_list))
+               return atchan->descs_allocated;
+
+       /* Allocate initial pool of descriptors */
+       for (i = 0; i < INIT_NR_DESCS_PER_CHANNEL; i++) {
+               desc = atc_alloc_descriptor(chan, GFP_KERNEL);
+               if (!desc) {
+                       dev_err(atdma->dma_common.dev,
+                               "Only %d initial descriptors\n", i);
+                       break;
+               }
+               list_add_tail(&desc->desc_node, &tmp_list);
+       }
+
+       spin_lock_bh(&atchan->lock);
+       atchan->descs_allocated = i;
+       list_splice(&tmp_list, &atchan->free_list);
+       atchan->completed_cookie = chan->cookie = 1;
+       spin_unlock_bh(&atchan->lock);
+
Quoted 8 lines

drivers/dma/at_hdmac.c line 709

Quoted 4 lines
drivers/dma/at_hdmac.c new file +4 -0
+       /* channel parameters */
+       channel_writel(atchan, CFG, ATC_DEFAULT_CFG);
+
+       tasklet_init(&atchan->tasklet, atc_tasklet, (unsigned long)atchan);

This routine may be called while the channel is already active, potentially causing tasklet_init() to be called while a tasklet is pending. Can this move to at_dma_probe()?

Oh, really ? In [TAG] above, I protect the call of this function when channel is enabled. Is the code at [TAG] ok ?

Ok, so I move all this.

Quoted 6 lines

drivers/dma/at_hdmac.c line 713

Quoted 4 lines
drivers/dma/at_hdmac.c new file +4 -0
+       /* clear any pending interrupt */
+       while (dma_readl(atdma, EBCISR))
+               cpu_relax();
+       atc_enable_irq(atchan);

ditto.

Ok.

I will regenerate a new patch as soon as you acknowledge my comments.

Thanks for your help, kind regards,

Signature · 1 line
Nicolas Ferre
#3 lore raw
Quoted 7 lines · Nicolas Ferre
Quoted 3 lines
Quoted 1 line
 include/linux/at_hdmac.h                |   26 +

...this header should be moved somewhere under arch/arm/include.

This is where dw_dmac.h resides. Moreover, if one day this IP is implemented on a different architecture, it will be good not to reach it through arch/arm path.

Ok, I won't gate acceptance on this since dw_dmac already set the precedent, but shouldn't the header move after the IP has been duplicated? Just my 2cents.

Quoted 11 lines
Quoted 7 lines

drivers/dma/at_hdmac.c line 81

Quoted 3 lines
drivers/dma/at_hdmac.c new file +3 -0
+               memset(desc, 0, sizeof(struct at_desc));
+               dma_async_tx_descriptor_init(&desc->txd, chan);
+               async_tx_ack(&desc->txd);

the DMA_CTRL_ACK bit is under control of the client. It should be read-only to the driver (except for extra descriptors that the driver creates on behalf of the client).

This is precisely where the descriptors are been created so, I thought it should be ok to initialize this bit. Am I right ?

They will be acknowledged by client code. Calls like async_memcpy assume that the the ack bit is clear by default so they can specify some actions to run at completion time. By setting it early, at descriptor allocation time, async_tx will get confused.

Quoted 61 lines
Quoted 10 lines
Quoted 10 lines
drivers/dma/at_hdmac.c new file +10 -0
+/**
+ * atc_alloc_chan_resources - allocate resources for DMA channel
+ * @chan: allocate descriptor resources for this channel
+ * @client: current client requesting the channel be ready for requests
+ *
+ * return - the number of allocated descriptors
+ */
+static int atc_alloc_chan_resources(struct dma_chan *chan,
+                                   struct dma_client *client)
+{
Quoted 8 lines

drivers/dma/at_hdmac.c line 678

Quoted 8 lines
drivers/dma/at_hdmac.c new file +8 -0
+       struct at_dma_chan      *atchan = to_at_dma_chan(chan);
+       struct at_dma           *atdma = to_at_dma(chan->device);
+       struct at_desc          *desc;
+       int                     i;
+       LIST_HEAD(tmp_list);
+
+       dev_vdbg(&chan->dev, "alloc_chan_resources\n");
+

[TAG]

Quoted 5 lines

drivers/dma/at_hdmac.c line 683

Quoted 5 lines
drivers/dma/at_hdmac.c new file +5 -0
+       /* ASSERT:  channel is idle */
+       if (atc_chan_is_enabled(atchan)) {
+               dev_dbg(&chan->dev, "DMA channel not idle ?\n");
+               return -EIO;
+       }

[/TAG]

Quoted 23 lines
Quoted 23 lines
drivers/dma/at_hdmac.c new file +23 -0
+
+       /* have we already been set up? */
+       if (!list_empty(&atchan->free_list))
+               return atchan->descs_allocated;
+
+       /* Allocate initial pool of descriptors */
+       for (i = 0; i < INIT_NR_DESCS_PER_CHANNEL; i++) {
+               desc = atc_alloc_descriptor(chan, GFP_KERNEL);
+               if (!desc) {
+                       dev_err(atdma->dma_common.dev,
+                               "Only %d initial descriptors\n", i);
+                       break;
+               }
+               list_add_tail(&desc->desc_node, &tmp_list);
+       }
+
+       spin_lock_bh(&atchan->lock);
+       atchan->descs_allocated = i;
+       list_splice(&tmp_list, &atchan->free_list);
+       atchan->completed_cookie = chan->cookie = 1;
+       spin_unlock_bh(&atchan->lock);
+
+       /* channel parameters */
Quoted 8 lines
Quoted 4 lines
drivers/dma/at_hdmac.c new file +3 -0
+       channel_writel(atchan, CFG, ATC_DEFAULT_CFG);
+
+       tasklet_init(&atchan->tasklet, atc_tasklet, (unsigned

long)atchan);

This routine may be called while the channel is already active, potentially causing tasklet_init() to be called while a tasklet is pending. Can this move to at_dma_probe()?

Quoted 2 lines

Oh, really ? In [TAG] above, I protect the call of this function when channel is enabled. Is the code at [TAG] ok ?

Yes, but it still feels like something that should be moved to the probe routine. In any event with the dmaengine rework I posted recently [1] ->device_alloc_chan_resources() will no longer be called multiple times without a ->free_chan_resources() inbetween.

Quoted 3 lines

I will regenerate a new patch as soon as you acknowledge my comments.

Thanks for your help, kind regards,

Thanks Nicolas.

Regards,
Dan

[1] http://marc.info/?l=linux-kernel&m=122669881026508&w=2

#4 lore raw

Dan Williams :

Quoted 10 lines · Nicolas Ferre
Quoted 5 lines
Quoted 2 lines
Quoted 1 line
 include/linux/at_hdmac.h                |   26 +

...this header should be moved somewhere under arch/arm/include.

This is where dw_dmac.h resides. Moreover, if one day this IP is implemented on a different architecture, it will be good not to reach it through arch/arm path.

Ok, I won't gate acceptance on this since dw_dmac already set the precedent, but shouldn't the header move after the IP has been duplicated? Just my 2cents.

Ok, I follow your advice.

Quoted 6 lines
Quoted 6 lines
Quoted 6 lines

drivers/dma/at_hdmac.c line 81

Quoted 3 lines
drivers/dma/at_hdmac.c new file +3 -0
+               memset(desc, 0, sizeof(struct at_desc));
+               dma_async_tx_descriptor_init(&desc->txd, chan);
+               async_tx_ack(&desc->txd);

the DMA_CTRL_ACK bit is under control of the client. It should be read-only to the driver (except for extra descriptors that the driver creates on behalf of the client).

Quoted 8 lines
Quoted 3 lines

This is precisely where the descriptors are been created so, I thought it should be ok to initialize this bit. Am I right ?

They will be acknowledged by client code. Calls like async_memcpy assume that the the ack bit is clear by default so they can specify some actions to run at completion time. By setting it early, at descriptor allocation time, async_tx will get confused.

This ack bit is annoying me : I cannot figure out how it is used for plain memcopy/slave offload calls...

Moreover, at recycle time, if I keep a descriptor chain as a whole, I have to introduce another state for my descriptors : consumed but not freed yet (with another linked list management). If I only take care of the ACK flag for releasing descriptors, I loose the dependency in my descriptor chain (in a multi-descriptor memcpy case).

Can I only consider this information without taking care of the chaining dependency (and loose this information in a multi-descriptor operation) ? Or, may I drop this DMA_CTRL_ACK bit management as I do not have the usefulness of redoing an operations on one descriptor (no xor engine) ?

Kind regards,

Signature · 1 line
Nicolas Ferre
#5 lore raw
Quoted 6 lines · Nicolas Ferre
Quoted 5 lines

They will be acknowledged by client code. Calls like async_memcpy assume that the the ack bit is clear by default so they can specify some actions to run at completion time. By setting it early, at descriptor allocation time, async_tx will get confused.

Quoted 8 lines

This ack bit is annoying me : I cannot figure out how it is used for plain memcopy/slave offload calls...

Moreover, at recycle time, if I keep a descriptor chain as a whole, I have to introduce another state for my descriptors : consumed but not freed yet (with another linked list management).
If I only take care of the ACK flag for releasing descriptors, I loose the dependency in my descriptor chain (in a multi-descriptor memcpy case).

Maybe I misread your driver... in the multi-descriptor memcpy case it is perfectly fine to set the ack-bit in the driver for all but the last descriptor in the chain. The client is only expected to attach dependencies at the end of the chain.

Quoted 2 lines

Can I only consider this information without taking care of the chaining dependency (and loose this information in a multi-descriptor operation) ?

You can lose it for all but the last descriptor.

Quoted 3 lines

Or, may I drop this DMA_CTRL_ACK bit management as I do not have the usefulness of redoing an operations on one descriptor (no xor engine) ?

If you will never need to run async_memcpy and don't want to handle the bit then you could set DMA_PRIVATE and the channels would never be picked up by the async_tx api. But, I am not convinced we need to take that step yet.

Quoted 4 lines

Kind regards,
--
Nicolas Ferre

Thanks,
Dan