serial base baud misdetected in 2.6.27
I'm running an ATCA7101 board. This board has two 16550 ports that get detected as ttyS4 and ttyS5.
With a much earlier kernel (2.6.14) the serial port base speed is correctly detected as 230400, which gives the desired 115200 when I specify that on the kernel commandline.
With 2.6.16 and 2.6.27 (not sure about the intervening kernels) the serial port base speed is detected as 921600, which means that I need to specify 460800 on the commandline to get a real speed of 115200 (as verified by an external terminal server).
Any ideas what could be causing this misdetection? I'm having lab issues right now so I can't track it down, but I'll have a go at it eventually.
Thanks,
Chris
Quoted 8 lines · On Tue, 04 Nov 2008 12:24:45 -0600 "Chris Friesen" <[email protected]> wrote:
I'm running an ATCA7101 board. This board has two 16550 ports that get detected as ttyS4 and ttyS5.
With a much earlier kernel (2.6.14) the serial port base speed is correctly detected as 230400, which gives the desired 115200 when I specify that on the kernel commandline.
Quoted 8 lines
With 2.6.16 and 2.6.27 (not sure about the intervening kernels) the serial port base speed is detected as 921600, which means that I need to specify 460800 on the commandline to get a real speed of 115200 (as verified by an external terminal server).
Any ideas what could be causing this misdetection? I'm having lab issues right now so I can't track it down, but I'll have a go at it eventually.
If this is a PCI card it may be matching against a PCI entry for a similar card with different crystals and need the right svid/sdid adding.
Quoted 5 lines · Alan Cox
Quoted 2 lines · On Tue, 04 Nov 2008 12:24:45 -0600 "Chris Friesen" <[email protected]> wrote:
I'm running an ATCA7101 board. This board has two 16550 ports that get detected as ttyS4 and ttyS5.
Quoted 8 lines
Quoted 5 lines
With a much earlier kernel (2.6.14) the serial port base speed is correctly detected as 230400, which gives the desired 115200 when I specify that on the kernel commandline.
With 2.6.16 and 2.6.27 (not sure about the intervening kernels) the serial port base speed is detected as 921600, which means that I need to specify 460800 on the commandline to get a real speed of 115200 (as verified by an external terminal server).
Any ideas what could be causing this misdetection? I'm having lab issues right now so I can't track it down, but I'll have a go at it eventually.
If this is a PCI card it may be matching against a PCI entry for a similar card with different crystals and need the right svid/sdid adding.
This is an ATCA board, so it's not a separate PCI card, but it does look like it's hanging off the PCI bus. The vendor/device matches to an Exar Corp. XR17C152, which is given a base_baud of 921600 in drivers/serial/8250_pci.c.
According to the chip specs, 921600 is correct with the default crystal and control register values. However, other crystals can be used and there's also a control register bit to enable a prescalar which cuts the baud rate by a factor of four. I suspect that one of these has been done on our boards.
The confusing thing is that the 2.6.14 code seems to also use a value of 921600, but somehow it works. I wonder if our kernel vendor has tweaked something in the code to adjust this value later on.
Chris
Quoted 9 lines
like it's hanging off the PCI bus. The vendor/device matches to an Exar Corp. XR17C152, which is given a
base_baudof 921600 indrivers/serial/8250_pci.c.According to the chip specs, 921600 is correct with the default crystal and control register values. However, other crystals can be used and there's also a control register bit to enable a prescalar which cuts the baud rate by a factor of four. I suspect that one of these has been done on our boards.
Probably. Did your vendor have the sense to set subvendor/subdevice identifiers that can be used to identify that specific unit ?
Quoted 6 lines · Alan Cox
Quoted 3 lines
like it's hanging off the PCI bus. The vendor/device matches to an Exar Corp. XR17C152, which is given a
base_baudof 921600 indrivers/serial/8250_pci.c.According to the chip specs, 921600 is correct with the default crystal and control register values. However, other crystals can be used and there's also a control register bit to enable a prescalar which cuts the baud rate by a factor of four. I suspect that one of these has been done on our boards.
Probably. Did your vendor have the sense to set subvendor/subdevice identifiers that can be used to identify that specific unit ?
No idea, but I'll look into it. Thanks for the help.
Chris