Skip to contentSkip to conversation

bootm command: is there any load address limitation for fdt?

U-Boot Richard Retanubun 3 participants 4 messages Dec 10, 2008 – Dec 11, 2008

lore
Share & tools
lore
#0 lore raw

Hi,

I am using u-boot version 2008.10 + git commit 13d36ec849785453953d00220b2c7dc66644a3c2

The board is a custom MPC8360E, similar to MPC8360EMDS from freescale.

My DDR-SDRAM is at address 0x0 - 0x1FFFFFFF

I am trying to limit the amount of memory needed to load and boot a linux kernel (2.6.26)

to do this I loaded my fdt at address 0x20_0000 and uImage at 0x_30_0000

When I run bootm, I both the kernel and fdt passed their checksum tests, and then I got this error.

ERROR: image is not a fdt - must RESET the board to recover.

However, if I loaded my fdt at address 0x40_0000 and uImage at 0x50_0000, bootm works fine.

Is there a reason why fdt must be loaded at a specific offset from the start of RAM?

Thank you for all your time

- Richard Retanubun.

#1 lore raw

Dear Richard Retanubun,

Quoted 6 lines · In message <[email protected]> you wrote:

I am trying to limit the amount of memory needed to load and boot a linux kernel (2.6.26) to do this I loaded my fdt at address 0x20_0000 and uImage at 0x_30_0000

When I run bootm, I both the kernel and fdt passed their checksum tests, and then I got this error.
ERROR: image is not a fdt - must RESET the board to recover.

...so the uncompressed Linux kernel image was written on top of your FDT image, corrupting it.

Quoted 1 line

However, if I loaded my fdt at address 0x40_0000 and uImage at 0x50_0000, bootm works fine.

Makes sense.

Quoted 1 line

Is there a reason why fdt must be loaded at a specific offset from the start of RAM?

Yes, there is - you need free space to load the uncompressed Linux kernel to low memory.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Dealing with failure is easy: work hard to improve. Success  is  also
easy  to  handle:  you've  solved  the  wrong  problem.  Work hard to
improve.
#2 lore raw
Quoted 5 lines · Wolfgang Denk

Dear Richard Retanubun,

Quoted 2 lines · In message <[email protected]> you wrote:

I am trying to limit the amount of memory needed to load and boot a linux kernel (2.6.26) to do this I loaded my fdt at address 0x20_0000 and uImage at 0x_30_0000

FWIIW, your FDT blob should be a whole lot less than 1MB, like 4K-16K. I've taken to loading it 0x8000 (32K) before my linux image.

[snip Wolfgang's diagnosis of the overwrite problem]

Best regards,
gvb

#3 lore raw
Quoted 11 lines · Jerry Van Baren
Quoted 5 lines · Wolfgang Denk

Dear Richard Retanubun,

Quoted 2 lines · In message <[email protected]> you wrote:

I am trying to limit the amount of memory needed to load and boot a linux kernel (2.6.26) to do this I loaded my fdt at address 0x20_0000 and uImage at 0x_30_0000

FWIIW, your FDT blob should be a whole lot less than 1MB, like 4K-16K. I've taken to loading it 0x8000 (32K) before my linux image.

[snip Wolfgang's diagnosis of the overwrite problem]

Dear Wolfgang and Jerry,

D'oh! I forgot that my uImage is compressed. Thank you for the prompt diagnosis.

My FDT blob is a whole lot less than 1MB, thanks for the 32K recommendation.

- Richard Retanubun.