Skip to contentSkip to conversation

EHCI last patch

U-Boot michael 2 participants 4 messages Dec 12, 2008 – Dec 17, 2008

lore
Share & tools
lore

michael

author
#0 lore raw

Hi all,

In the last ehci patch I add myself in the author of the code. I'm not sure if it possible. I change
the codes and test it but I don't know if the change are sufficient.

Regards Michael

#1 lore raw

Hi Michael,

Quoted 3 lines · michael

In the last ehci patch I add myself in the author of the code. I'm not sure if it possible. I change
the codes and test it but I don't know if the change are sufficient.

You added yourself not as author but you added your Copyright. With all the work you have done to this code lately I'm pretty sure that this is ok.

Thanks for all your work on this. And please don't forget to add the EHCI-PCI support as well.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

author
#2 lore raw

Hi all,

Quoted 9 lines · Stefan Roese

Hi Michael,

Quoted 4 lines · michael

In the last ehci patch I add myself in the author of the code. I'm not sure if it possible. I change
the codes and test it but I don't know if the change are sufficient.

Quoted 6 lines

You added yourself not as author but you added your Copyright. With all the work you have done to this code lately I'm pretty sure that this is ok.

Thanks for all your work on this. And please don't forget to add the EHCI-PCI support as well.

I have rewrite and clean the support for ehci-pci but I don't have any hardware to test on it. My
code is like this:

int ehci_hcd_init(void)

{
        pci_dev_t pdev;
        uint32_t addr;

        pdev = pci_find_devices(ehci_pci_ids, CONFIG_PCI_EHCI_DEVICE);
        if (dev == -1) {
                printf("EHCI host controller not found\n");
                return -1;
        }

        pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &addr);
        hccr = (struct ehci_hccr *)addr;
        hcor = (struct ehci_hcor *)((uint32_t) hccr +
                        HC_LENGTH(ehci_readl(&hccr->cr_capbase)));

        return 0;
}

and the CONFIG_PCI_EHCI_DEVICE. I notice that there is a table in usb_ohci too. Is there any
reason?

#ifdef CONFIG_PCI_EHCI_DEVICE

static struct pci_device_id ehci_pci_ids[] = {
        /* Please add supported PCI EHCI controller ids here */
        {0, 0}
};

#endif

It is very simple. The problem is thath currently I don't have any other hardware to test the code.
I have done some cleanup and I have the ixp4xx usb host support ready too. Are there people with ehci
hardware running u-boot?

Michael

#3 lore raw

Hi Michael,

Quoted 28 lines · michael

I have rewrite and clean the support for ehci-pci but I don't have any hardware to test on it. My
code is like this:

int ehci_hcd_init(void)

{
        pci_dev_t pdev;
        uint32_t addr;

        pdev = pci_find_devices(ehci_pci_ids, CONFIG_PCI_EHCI_DEVICE);
        if (dev == -1) {
                printf("EHCI host controller not found\n");
                return -1;
        }

        pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &addr);
        hccr = (struct ehci_hccr *)addr;
        hcor = (struct ehci_hcor *)((uint32_t) hccr +
                        HC_LENGTH(ehci_readl(&hccr->cr_capbase)));

        return 0;
}

and the CONFIG_PCI_EHCI_DEVICE. I notice that there is a table in usb_ohci too. Is there any
reason?

#ifdef CONFIG_PCI_EHCI_DEVICE

Quoted 8 lines
static struct pci_device_id ehci_pci_ids[] = {
        /* Please add supported PCI EHCI controller ids here */
        {0, 0}
};

#endif

It is very simple. The problem is thath currently I don't have any other hardware to test the code.

That's ok for now. I will test on one of my systems and add the needed PCI ID(s).

Quoted 3 lines

I have done some cleanup and I have the ixp4xx usb host support ready too. Are there people with ehci
hardware running u-boot?

There are many, I'm sure. For example some PPC4xx variants which could use this EHCI support. So I'm pretty sure that patches for supporting other EHCI controllers will follow soon once your patches hit mainline (next merge window I suspect).

Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================