Skip to contentSkip to conversation

A bug with multiple devices?

DISCUSSION Shen Feng 5 participants 12 messages Dec 30, 2008 – Jan 1, 2009 Btrfs file system

lore
Share & tools
lore

Shen Feng

author
#0 lore raw

Hi,

I create a raid-1 btrfs with the following command.

[root@localhost ~]# fdisk -l /dev/sdb

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xb44829ea

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        4863    39062016   83  Linux
/dev/sdb2            4864        9726    39062047+  83  Linux
/dev/sdb3            9727       38905   234375905+   f  W95 Ext'd (LBA)
/dev/sdb5            9727       14590    39063374   83  Linux
/dev/sdb6           14590       19453    39068690+   7  HPFS/NTFS
/dev/sdb7           19454       29178    78116031   83  Linux
/dev/sdb8           29179       31610    19535008+  83  Linux
/dev/sdb9           31611       34041    19526976   83  Linux
/dev/sdb10          34042       36473    19535008+  83  Linux
/dev/sdb11          36474       38904    19526976   83  Linux

[root@localhost ~]# mkfs.btrfs -m raid1 /dev/sdb8 /dev/sdb9 /dev/sdb10 /dev/sdb11 adding device /dev/sdb9 id 2
adding device /dev/sdb10 id 3
adding device /dev/sdb11 id 4
fs created label (null) on /dev/sdb8

	nodesize 4096 leafsize 4096 sectorsize 4096 size 74.50GB

Btrfs v0.16-29-g0d53b21

[root@localhost ~]# mount -t btrfs /dev/sdb8 /mnt/btrfs[root@localhost ~]# df
Filesystem 1K-blocks Used Available Use% Mounted on
...
/dev/sdb8 78123968 28 78123940 1% /mnt/btrfs

I think the partition size is no correct since this is a raid-1 partition. The size should be half.
Is this a bug?

-Shen

#1 lore raw
Quoted 2 lines · Shen Feng

I think the partition size is no correct since this is a raid-1 partition. The size should be half.

I've just run into this myself and so can confirm this issue on a btrfs filesystem with 2 devices, where it is created by doing:

mkfs.btrfs -m raid1 /dev/sda10 /dev/sda11

modprobe btrfs

btrfsctl -a

mount /dev/sda10 /home

The df command shows it has twice the space I was expecting (61GB rather than 30GB). The btrfs-show command shows that it has two devices but doesn't
appear to contain any way to show the RAID level implemented. I get the
same outcome if I mount /dev/sda11 instead of sda10.

Any ideas ?

Chris

Signature · 4 lines
 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP
#2 lore raw
Quoted 1 line · Chris Samuel

mkfs.btrfs -m raid1 /dev/sda10 /dev/sda11

Even doing what appears to be the correct method of:

mkfs.btrfs -d raid1 -m raid1 /dev/sda10 /dev/sda11

doesn't give any love, mkfs.btrfs still tells me the filesystem will be 60GB (and the kernel agrees when it is mounted).

But mkfs.btrfs does correctly set data_profile to include BTRFS_BLOCK_GROUP_RAID1 and does indeed call create_one_raid_group() with BTRFS_BLOCK_GROUP_DATA in create_raid_groups() in mkfs.c.

cheers,
Chris

Signature · 4 lines
 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP
#4 lore raw
In reply to Chris Samuel

2008/12/30 Chris Samuel <[email protected]>:

Quoted 14 lines · Shen Feng
Quoted 3 lines

I think the partition size is no correct since this is a raid-1 partition. The size should be half.

I've just run into this myself and so can confirm this issue on a btrfs filesystem with 2 devices, where it is created by doing:

mkfs.btrfs -m raid1 /dev/sda10 /dev/sda11

modprobe btrfs

btrfsctl -a

Quoted 9 lines

mount /dev/sda10 /home

The df command shows it has twice the space I was expecting (61GB rather than 30GB). The btrfs-show command shows that it has two devices but doesn't
appear to contain any way to show the RAID level implemented. I get the
same outcome if I mount /dev/sda11 instead of sda10.

Any ideas ?

This is a known bug. In btrfs, chunks are created dynamically and may have different RAID configurations. So it's difficult to compute the space in advance.

Regards
Yan Zheng

#5 lore raw
Quoted 3 lines · Yan Zheng

This is a known bug. In btrfs, chunks are created dynamically and may have different RAID configurations.  So it's difficult to compute the space in advance.

Thanks Yan!

So mkfs.btrfs -d raid1 just sets the default value ?

All the best,
Chris

Signature · 4 lines
 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP
#6 lore raw
In reply to Yan Zheng
Quoted 1 line · Yan Zheng

So it's difficult to compute the space in advance.

One thought would be to choose the most conservative RAID configuration for the
number of devices in the system. But then you have the opposite issue of
potentially showing too little space in some situations.

But my guess is that for most (>50%) people once they set a default RAID level then most will have everything in that state.

cheers,
Chris

Signature · 4 lines
 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP
#3 lore raw
In reply to Chris Samuel
Quoted 6 lines · Chris Samuel
Quoted 1 line · Chris Samuel

mkfs.btrfs -m raid1 /dev/sda10 /dev/sda11

Even doing what appears to be the correct method of:

Quoted 8 lines

mkfs.btrfs -d raid1 -m raid1 /dev/sda10 /dev/sda11

doesn't give any love, mkfs.btrfs still tells me the filesystem will be 60GB (and the kernel agrees when it is mounted).

But mkfs.btrfs does correctly set data_profile to include BTRFS_BLOCK_GROUP_RAID1 and does indeed call create_one_raid_group() with BTRFS_BLOCK_GROUP_DATA in create_raid_groups() in mkfs.c.

This is one of those things I've left for later.

Basically df tells you the total storage in the FS. This storage might be raid0, raid1 or single spindle duplication, so the usable space may be different from the total storage.

In the future we'll have the data sent to df give better estimates of usable space.

Changing btrfs-show to show the chunks too is a good idea.

-chris

author
#7 lore raw
In reply to Shen Feng
Quoted 28 lines · Shen Feng

Hi,

I create a raid-1 btrfs with the following command.

[root@localhost ~]# fdisk -l /dev/sdb

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xb44829ea

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        4863    39062016   83  Linux
/dev/sdb2            4864        9726    39062047+  83  Linux
/dev/sdb3            9727       38905   234375905+   f  W95 Ext'd (LBA)
/dev/sdb5            9727       14590    39063374   83  Linux
/dev/sdb6           14590       19453    39068690+   7  HPFS/NTFS
/dev/sdb7           19454       29178    78116031   83  Linux
/dev/sdb8           29179       31610    19535008+  83  Linux
/dev/sdb9           31611       34041    19526976   83  Linux
/dev/sdb10          34042       36473    19535008+  83  Linux
/dev/sdb11          36474       38904    19526976   83  Linux

[root@localhost ~]# mkfs.btrfs -m raid1 /dev/sdb8 /dev/sdb9 /dev/sdb10 /dev/sdb11 adding device /dev/sdb9 id 2
adding device /dev/sdb10 id 3
adding device /dev/sdb11 id 4
fs created label (null) on /dev/sdb8

Quoted 8 lines
	nodesize 4096 leafsize 4096 sectorsize 4096 size 74.50GB

Btrfs v0.16-29-g0d53b21

[root@localhost ~]# mount -t btrfs /dev/sdb8 /mnt/btrfs[root@localhost ~]# df
Filesystem 1K-blocks Used Available Use% Mounted on
...
/dev/sdb8 78123968 28 78123940 1% /mnt/btrfs

More test:

[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 28K 75G 1% /mnt/btrfs
[root@localhost btrfs]# dd if=/dev/zero of=/mnt/btrfs/file bs=1024 count=1024 1024+0 records in
1024+0 records out
1048576 bytes (1.0 MB) copied, 0.0481317 s, 21.8 MB/s [root@localhost btrfs]# sync
[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 1.1M 75G 1% /mnt/btrfs

With raid-1, the used space may be double (about 2.2M), I think.

Quoted 11 lines

I think the partition size is no correct since this is a raid-1 partition. The size should be half.
Is this a bug?

-Shen
--
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 13 lines
Best Regards,
--------------------------------------------------
Shen Feng
Development Dept.I
Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST)
8/F., Civil Defense Building, No.189 Guangzhou Road,
Nanjing, 210029, China
PHONE: +86-25-86630566-950
COINS: 79955-950
FAX: +86-25-83317685
MAIL: [email protected]
-------------------------------------------------
This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited.  If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed.
#8 lore raw

mkfs.btrfs -m raid1 just means 'meta data' works as raid1

You should try mkfs.btrfs -d raid1

This maybe help:
mkfs.btrfs [-A <offset>] [-b <size>] [-l <size>] [-n <size>] [-l <label>] [-s <size>] [-m raid0|raid1|raid10|single] [-d raid0|raid1|raid10|single] <device>

2008/12/31 Shen Feng <[email protected]>:

Quoted 89 lines
Quoted 28 lines · Shen Feng

Hi,

I create a raid-1 btrfs with the following command.

[root@localhost ~]# fdisk -l /dev/sdb

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xb44829ea

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        4863    39062016   83  Linux
/dev/sdb2            4864        9726    39062047+  83  Linux
/dev/sdb3            9727       38905   234375905+   f  W95 Ext'd (LBA)
/dev/sdb5            9727       14590    39063374   83  Linux
/dev/sdb6           14590       19453    39068690+   7  HPFS/NTFS
/dev/sdb7           19454       29178    78116031   83  Linux
/dev/sdb8           29179       31610    19535008+  83  Linux
/dev/sdb9           31611       34041    19526976   83  Linux
/dev/sdb10          34042       36473    19535008+  83  Linux
/dev/sdb11          36474       38904    19526976   83  Linux

[root@localhost ~]# mkfs.btrfs -m raid1 /dev/sdb8 /dev/sdb9 /dev/sdb10 /dev/sdb11 adding device /dev/sdb9 id 2
adding device /dev/sdb10 id 3
adding device /dev/sdb11 id 4
fs created label (null) on /dev/sdb8

Quoted 8 lines
      nodesize 4096 leafsize 4096 sectorsize 4096 size 74.50GB

Btrfs v0.16-29-g0d53b21

[root@localhost ~]# mount -t btrfs /dev/sdb8 /mnt/btrfs[root@localhost ~]# df
Filesystem 1K-blocks Used Available Use% Mounted on
...
/dev/sdb8 78123968 28 78123940 1% /mnt/btrfs

More test:

[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 28K 75G 1% /mnt/btrfs
[root@localhost btrfs]# dd if=/dev/zero of=/mnt/btrfs/file bs=1024 count=1024 1024+0 records in
1024+0 records out
1048576 bytes (1.0 MB) copied, 0.0481317 s, 21.8 MB/s [root@localhost btrfs]# sync
[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 1.1M 75G 1% /mnt/btrfs

With raid-1, the used space may be double (about 2.2M), I think.

Quoted 11 lines

I think the partition size is no correct since this is a raid-1 partition. The size should be half.
Is this a bug?

-Shen
--
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
Best Regards,
--------------------------------------------------
Shen Feng
Development Dept.I
Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST)
8/F., Civil Defense Building, No.189 Guangzhou Road,
Nanjing, 210029, China
PHONE: +86-25-86630566-950
COINS: 79955-950
FAX: +86-25-83317685
MAIL: [email protected]
-------------------------------------------------
This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited. If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed. --
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 3 lines
Thanks & Best Regards
Liu Hui
--
author
#9 lore raw
Quoted 8 lines · Liu Hui

mkfs.btrfs -m raid1 just means 'meta data' works as raid1

You should try mkfs.btrfs -d raid1

This maybe help:
mkfs.btrfs [-A <offset>] [-b <size>] [-l <size>] [-n <size>] [-l <label>] [-s <size>] [-m raid0|raid1|raid10|single] [-d raid0|raid1|raid10|single] <device>

Thanks.

The problem still exists with -d option.

[root@localhost ~]# mkfs.btrfs -m raid1 -d raid1 /dev/sdb8 /dev/sdb9 /dev/sdb10 /dev/sdb11 adding device /dev/sdb9 id 2
adding device /dev/sdb10 id 3
adding device /dev/sdb11 id 4
fs created label (null) on /dev/sdb8

	nodesize 4096 leafsize 4096 sectorsize 4096 size 74.50GB

Btrfs v0.16-29-g0d53b21
[root@localhost ~]# btrfsctl -a
Scanning for Btrfs filesystems
[root@localhost ~]# mount -t btrfs /dev/sdb8 /mnt/btrfs [root@localhost ~]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 28K 75G 1% /mnt/btrfs
[root@localhost ~]# dd if=/dev/zero of=/mnt/btrfs/file bs=1024 count=1024 1024+0 records in
1024+0 records out
1048576 bytes (1.0 MB) copied, 0.0199063 s, 52.7 MB/s [root@localhost ~]# sync
[root@localhost ~]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 1.1M 75G 1% /mnt/btrfs

Quoted 91 lines

2008/12/31 Shen Feng <[email protected]>:

Quoted 86 lines
Quoted 28 lines · Shen Feng

Hi,

I create a raid-1 btrfs with the following command.

[root@localhost ~]# fdisk -l /dev/sdb

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xb44829ea

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        4863    39062016   83  Linux
/dev/sdb2            4864        9726    39062047+  83  Linux
/dev/sdb3            9727       38905   234375905+   f  W95 Ext'd (LBA)
/dev/sdb5            9727       14590    39063374   83  Linux
/dev/sdb6           14590       19453    39068690+   7  HPFS/NTFS
/dev/sdb7           19454       29178    78116031   83  Linux
/dev/sdb8           29179       31610    19535008+  83  Linux
/dev/sdb9           31611       34041    19526976   83  Linux
/dev/sdb10          34042       36473    19535008+  83  Linux
/dev/sdb11          36474       38904    19526976   83  Linux

[root@localhost ~]# mkfs.btrfs -m raid1 /dev/sdb8 /dev/sdb9 /dev/sdb10 /dev/sdb11 adding device /dev/sdb9 id 2
adding device /dev/sdb10 id 3
adding device /dev/sdb11 id 4
fs created label (null) on /dev/sdb8

Quoted 8 lines
      nodesize 4096 leafsize 4096 sectorsize 4096 size 74.50GB

Btrfs v0.16-29-g0d53b21

[root@localhost ~]# mount -t btrfs /dev/sdb8 /mnt/btrfs[root@localhost ~]# df
Filesystem 1K-blocks Used Available Use% Mounted on
...
/dev/sdb8 78123968 28 78123940 1% /mnt/btrfs

More test:

[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 28K 75G 1% /mnt/btrfs
[root@localhost btrfs]# dd if=/dev/zero of=/mnt/btrfs/file bs=1024 count=1024 1024+0 records in
1024+0 records out
1048576 bytes (1.0 MB) copied, 0.0481317 s, 21.8 MB/s [root@localhost btrfs]# sync
[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 1.1M 75G 1% /mnt/btrfs

With raid-1, the used space may be double (about 2.2M), I think.

Quoted 11 lines

I think the partition size is no correct since this is a raid-1 partition. The size should be half.
Is this a bug?

-Shen
--
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
Best Regards,
--------------------------------------------------
Shen Feng
Development Dept.I
Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST)
8/F., Civil Defense Building, No.189 Guangzhou Road,
Nanjing, 210029, China
PHONE: +86-25-86630566-950
COINS: 79955-950
FAX: +86-25-83317685
MAIL: [email protected]
-------------------------------------------------
This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited. If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed. --
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 13 lines
Best Regards,
--------------------------------------------------
Shen Feng
Development Dept.I
Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST)
8/F., Civil Defense Building, No.189 Guangzhou Road,
Nanjing, 210029, China
PHONE: +86-25-86630566-950
COINS: 79955-950
FAX: +86-25-83317685
MAIL: [email protected]
-------------------------------------------------
This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited.  If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed.
author
#11 lore raw
In reply to Liu Hui
Quoted 8 lines · Liu Hui

mkfs.btrfs -m raid1 just means 'meta data' works as raid1

You should try mkfs.btrfs -d raid1

This maybe help:
mkfs.btrfs [-A <offset>] [-b <size>] [-l <size>] [-n <size>] [-l <label>] [-s <size>] [-m raid0|raid1|raid10|single] [-d raid0|raid1|raid10|single] <device>

Thanks.
I update the usage message of mkfs.btrfs with the following patch.

From: Shen Feng <[email protected]>

Improve the the mkfs.btrfs usage message according to
http://btrfs.wiki.kernel.org/index.php/Mkfs.btrfs

---
 mkfs.c |    6 +++++-
 1 files changed, 5 insertions(+), 1 deletions(-)
mkfs.c +5 -1
index 89de8ac..be93aaa 100644
@@ -263,9 +263,13 @@ static void print_usage(void)
 {
 	fprintf(stderr, "usage: mkfs.btrfs [options] dev [ dev ... ]\n");
 	fprintf(stderr, "options:\n");
+	fprintf(stderr, "\t -A --alloc-start the offset to start the FS\n");
 	fprintf(stderr, "\t -b --byte-count total number of bytes in the FS\n");
+	fprintf(stderr, "\t -d --data data profile, raid0, raid1, raid10 or single\n");
 	fprintf(stderr, "\t -l --leafsize size of btree leaves\n");
-	fprintf(stderr, "\t -n --nodesize size of btree leaves\n");
+	fprintf(stderr, "\t -L --label set a label\n");
+	fprintf(stderr, "\t -m --metadata metadata profile, values like data profile\n");
+	fprintf(stderr, "\t -n --nodesize size of btree nodes\n");
 	fprintf(stderr, "\t -s --sectorsize min block allocation\n");
 	fprintf(stderr, "%s\n", BTRFS_BUILD_VERSION);
 	exit(1);

-- 1.6.0.6

Quoted 91 lines

2008/12/31 Shen Feng <[email protected]>:

Quoted 86 lines
Quoted 28 lines · Shen Feng

Hi,

I create a raid-1 btrfs with the following command.

[root@localhost ~]# fdisk -l /dev/sdb

Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xb44829ea

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        4863    39062016   83  Linux
/dev/sdb2            4864        9726    39062047+  83  Linux
/dev/sdb3            9727       38905   234375905+   f  W95 Ext'd (LBA)
/dev/sdb5            9727       14590    39063374   83  Linux
/dev/sdb6           14590       19453    39068690+   7  HPFS/NTFS
/dev/sdb7           19454       29178    78116031   83  Linux
/dev/sdb8           29179       31610    19535008+  83  Linux
/dev/sdb9           31611       34041    19526976   83  Linux
/dev/sdb10          34042       36473    19535008+  83  Linux
/dev/sdb11          36474       38904    19526976   83  Linux

[root@localhost ~]# mkfs.btrfs -m raid1 /dev/sdb8 /dev/sdb9 /dev/sdb10 /dev/sdb11 adding device /dev/sdb9 id 2
adding device /dev/sdb10 id 3
adding device /dev/sdb11 id 4
fs created label (null) on /dev/sdb8

Quoted 8 lines
      nodesize 4096 leafsize 4096 sectorsize 4096 size 74.50GB

Btrfs v0.16-29-g0d53b21

[root@localhost ~]# mount -t btrfs /dev/sdb8 /mnt/btrfs[root@localhost ~]# df
Filesystem 1K-blocks Used Available Use% Mounted on
...
/dev/sdb8 78123968 28 78123940 1% /mnt/btrfs

More test:

[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 28K 75G 1% /mnt/btrfs
[root@localhost btrfs]# dd if=/dev/zero of=/mnt/btrfs/file bs=1024 count=1024 1024+0 records in
1024+0 records out
1048576 bytes (1.0 MB) copied, 0.0481317 s, 21.8 MB/s [root@localhost btrfs]# sync
[root@localhost btrfs]# df -h /dev/sdb8
Filesystem Size Used Avail Use% Mounted on
/dev/sdb8 75G 1.1M 75G 1% /mnt/btrfs

With raid-1, the used space may be double (about 2.2M), I think.

Quoted 11 lines

I think the partition size is no correct since this is a raid-1 partition. The size should be half.
Is this a bug?

-Shen
--
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
Best Regards,
--------------------------------------------------
Shen Feng
Development Dept.I
Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST)
8/F., Civil Defense Building, No.189 Guangzhou Road,
Nanjing, 210029, China
PHONE: +86-25-86630566-950
COINS: 79955-950
FAX: +86-25-83317685
MAIL: [email protected]
-------------------------------------------------
This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited. If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed. --
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 13 lines
Best Regards,
--------------------------------------------------
Shen Feng
Development Dept.I
Nanjing Fujitsu Nanda Software Tech. Co., Ltd.(FNST)
8/F., Civil Defense Building, No.189 Guangzhou Road,
Nanjing, 210029, China
PHONE: +86-25-86630566-950
COINS: 79955-950
FAX: +86-25-83317685
MAIL: [email protected]
-------------------------------------------------
This communication is for use by the intended recipient(s) only and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you are not an intended recipient of this communication, you are hereby notified that any dissemination, distribution or copying hereof is strictly prohibited.  If you have received this communication in error, please notify me by reply e-mail, permanently delete this communication from your system, and destroy any hard copies you may have printed.
#10 lore raw
In reply to Shen Feng
Quoted 1 line · Shen Feng

The problem still exists with -d option.

As Chris Mason wrote in response to my query on this it's a known issue that's a consequence of different chunks potentially having different RAID levels.

The RAID level itself does appear to work - I tested it by copying a kernel image onto it, unmounted it, used debug-tree to work out the offset for it on one device of the RAID and blew a section away with dd. I remounted it and verified that the MD5 checksums still agreed with the original and there were kernel messages complaining about checksum mismatches showing that the damage had been detected and worked around.

cheers,
Chris

Signature · 4 lines
 Chris Samuel  :  http://www.csamuel.org/  :  Melbourne, VIC

This email may come with a PGP signature as a file. Do not panic.
For more info see: http://en.wikipedia.org/wiki/OpenPGP