Skip to contentSkip to conversation

Trouble moving custom MPC8548 board to U-boot 1.3

U-Boot Pieter 2 participants 2 messages Jan 12, 2009

lore
Share & tools
lore

Pieter

author
#0 lore raw

Hi all,

Quoted 11 lines
Quoted 8 lines

I have spent quite some time trying to move from U-Boot 1.2 to a newer version.. I am stuck at the initialization of the ram. The ram checksum fails and gives me a "total memory of 0". (the board has 512MB and work when booting uboot 1.2)

can anyone pls. point me in the right direction?

This is your root cause: Unable to get the SPD information for the DDR DIMM in slot 0 of controller 0.

Quoted 7 lines

What part are you using? Does it support SPD?
Is your I2C to it hooked up correctly?
Can you dump the SPD information that is read?
Does it match the part specs?

HTH,
jdl

I have managed to read the SPD data for the dram. I also confirmed that the dram control and timing settings correspond to the settings that worked in the previous uboot.
I am now able to run uboot up to the "relocate_code". The new Stack pointer is set to 0x0FF8DF58 witch is close enough to what i expected. This is however where the board hangs. (The board also hang when running the "testram"). I tried reading the data at the new stack pointer but get "SAP: read access failed" i get the same error when trying to read any address within the RAM or any address of other devices. This leads me to think that my LAW or TLB setup is incorrect.

Looking at LAW setup: (based on board sbc8548)

/* LAW(Local Access Window) configuration:

    * 0x0000_0000     0x1fff_ffff     DDR             512M/Auto
    * 0x8000_0000     0xbfff_ffff     PCI1 MEM        1G
    * 0xc000_0000     0xcfff_ffff     PCI1 IO         16M
    * 0xe000_0000     0xffff_ffff      LBC                       512M */
   struct law_entry law_table[] = {
   #ifndef CONFIG_SPD_EEPROM
           SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAWAR_SIZE_512M,
   LAWAR_TRGT_IF_DDR),
   #endif
           SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAWAR_SIZE_1G,
   LAWAR_TRGT_IF_PCI1 ),
           SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAWAR_SIZE_16M,
   LAWAR_TRGT_IF_PCI1),
           SET_LAW(CONFIG_SYS_LBC_BASE, LAWAR_SIZE_512M, LAWAR_TRGT_IF_LBC)
   };

Since my board uses SPD_EEPROM, where does the LAW entry for DDR get initilized or should the #ifndef statement be removed?

Am I on the right track to solving my problem?
thanks pieter

#1 lore raw

Hi Pieter,

Quoted 1 line

I have managed to read the SPD data for the dram. I also confirmed that the

dram control and timing settings correspond to the settings that worked in the >

Quoted 1 line

previous uboot.

So it mean that you r using a DIMM, where the configurations are available on the EEPROM.
Make sure u've decoded those values and put in below registers CS0_BNDS
CS1_BNDS
CS2_BNDS
CS3_BNDS
CS0_CONFIG
CS1_CONFIG
CS2_CONFIG
CS3_CONFIG
TIMING_CFG_3(EXT_REFREC)
TIMING_CFG_0
TIMING_CFG_1
TIMING_CFG_2
DDR_CFG
DDR_CFG_2
DDR_MODE
DDR_MODE_2
DDR_INTERVAL
DDR_CLK_CNTL
;DELAY 200
DDR_CFG

Quoted 1 line

I am now able to run uboot up to the "relocate_code". The new Stack pointer

is set to 0x0FF8DF58 witch is close enough to what i expected.

Quoted 1 line

This is however where the board hangs. (The board also hang when running

the "testram"). I tried reading the data at the new stack pointer but get "SAP: read >

Quoted 1 line

access failed" i get the same error when trying to read any address within

the RAM or any address of other devices. This leads me to think that my LAW or >

Quoted 1 line

TLB setup is incorrect.

After initializing the ram, the next thing u-boot does is relocating the monitor code from the Flast to the ram. If this fails then it might be some problem in accessing ram. This happens when the LAW is not properly initialized and the memory is not mapped properly. Make sure you map ur DDR.

Thanks,
Ajeesh Kumar

-----Original Message-----
From: [email protected] [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Pieter
Sent: Monday, January 12, 2009 1:45 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] Trouble moving custom MPC8548 board to U-boot 1.3

Hi all,

Quoted 11 lines
Quoted 8 lines

I have spent quite some time trying to move from U-Boot 1.2 to a newer version.. I am stuck at the initialization of the ram. The ram checksum fails and gives me a "total memory of 0". (the board has 512MB and work when booting uboot 1.2)

can anyone pls. point me in the right direction?

This is your root cause: Unable to get the SPD information for the DDR DIMM in slot 0 of controller 0.

Quoted 7 lines

What part are you using? Does it support SPD?
Is your I2C to it hooked up correctly?
Can you dump the SPD information that is read?
Does it match the part specs?

HTH,
jdl

I have managed to read the SPD data for the dram. I also confirmed that the dram control and timing settings correspond to the settings that worked in the previous uboot.
I am now able to run uboot up to the "relocate_code". The new Stack pointer is set to 0x0FF8DF58 witch is close enough to what i expected. This is however where the board hangs. (The board also hang when running the "testram"). I tried reading the data at the new stack pointer but get "SAP:
read access failed" i get the same error when trying to read any address within the RAM or any address of other devices. This leads me to think that my LAW or TLB setup is incorrect.

Looking at LAW setup: (based on board sbc8548)

/* LAW(Local Access Window) configuration:

    * 0x0000_0000     0x1fff_ffff     DDR             512M/Auto
    * 0x8000_0000     0xbfff_ffff     PCI1 MEM        1G
    * 0xc000_0000     0xcfff_ffff     PCI1 IO         16M
    * 0xe000_0000     0xffff_ffff      LBC                       512M */
   struct law_entry law_table[] = {
   #ifndef CONFIG_SPD_EEPROM
           SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAWAR_SIZE_512M,
   LAWAR_TRGT_IF_DDR),
   #endif
           SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAWAR_SIZE_1G,
   LAWAR_TRGT_IF_PCI1 ),
           SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAWAR_SIZE_16M,
   LAWAR_TRGT_IF_PCI1),
           SET_LAW(CONFIG_SYS_LBC_BASE, LAWAR_SIZE_512M, LAWAR_TRGT_IF_LBC)
   };

Since my board uses SPD_EEPROM, where does the LAW entry for DDR get initilized or should the #ifndef statement be removed?

Am I on the right track to solving my problem?
thanks pieter
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments contained in it.