Skip to contentSkip to conversation

Add W90P1board based on W90P710 ARM SoC

PATCH New Vovk Konstantin 2 participants 2 messages Feb 9, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 3/3 Add W90P1board based on W90P710 ARM SoC

W90P1 board support NAND and NOR Flash, IDE interface, optional LED for visualization. Changed makefile in /examples folder for support W90P710 SoC.

---
  MAINTAINERS                 |   13 ++-
  MAKEALL                     |    1 +
  Makefile                    |    3 +
  board/w90p1/Makefile        |   53 ++++++++++
  board/w90p1/config.mk       |   24 +++++
  board/w90p1/ide.c           |  120 +++++++++++++++++++++
  board/w90p1/led.c           |   61 +++++++++++
  board/w90p1/lowlevel_init.S |  124 ++++++++++++++++++++++
  board/w90p1/nand.c          |  106 +++++++++++++++++++
  board/w90p1/u-boot.lds      |   69 ++++++++++++
  board/w90p1/w90p1.c         |   95 +++++++++++++++++
  examples/Makefile           |    8 +-
  include/configs/W90P1.h     |  240 +++++++++++++++++++++++++++++++++++++++++++
  13 files changed, 908 insertions(+), 9 deletions(-)

create mode 100644 board/w90p1/Makefile
create mode 100644 board/w90p1/config.mk
create mode 100644 board/w90p1/ide.c
create mode 100644 board/w90p1/led.c
create mode 100644 board/w90p1/lowlevel_init.S
create mode 100644 board/w90p1/nand.c
create mode 100644 board/w90p1/u-boot.lds
create mode 100644 board/w90p1/w90p1.c
create mode 100644 include/configs/W90P1.h

MAINTAINERS +8 -5
index 38feac8..95b59dc 100644
@@ -62,7 +62,7 @@ Joe D'Abbraccio <[email protected]>
 
  	MPC837xERDB	MPC837x
 
-K?ri Dav??sson <[email protected]>
+K???ri Dav??????sson <[email protected]>
 
  	FLAGADM		MPC823
 
@@ -516,7 +516,7 @@ Peter Figuli <[email protected]>
 
  	wepep250	xscale
 
-Marius Gr?ger <[email protected]>
+Marius Gr???ger <[email protected]>
 
  	impa7		ARM720T (EP7211)
  	ep7312		ARM720T (EP7312)
@@ -566,7 +566,7 @@ Nishanth Menon <[email protected]>
 
  	omap3_zoom1	ARM CORTEX-A8 (OMAP3xx SoC)
 
-David M?ller <[email protected]>
+David M???ller <[email protected]>
 
  	smdk2410	ARM920T
  	VCMA9		ARM920T
@@ -646,7 +646,7 @@ Richard Woodruff <[email protected]>
 
  	omap2420h4	ARM1136EJS
 
-Alex Z?pke <[email protected]>
+Alex Z???pke <[email protected]>
 
  	lart		SA1100
  	dnp1110		SA1110
@@ -655,6 +655,9 @@ Sergey Lapin <[email protected]>
 
  	afeb9260	ARM926EJS (AT91SAM9260 SoC)
 
+Konstantin Vovk <[email protected]>
+	w90p1		ARM720T (W90P710 SoC)
+
  -------------------------------------------------------------------------
 
  Unknown / orphaned boards:
@@ -671,7 +674,7 @@ Unknown / orphaned boards:
  #	Board		CPU						#
  #########################################################################
 
-Daniel Engstr?m <[email protected]>
+Daniel Engstr???m <[email protected]>
 
  	sc520_cdp	x86
 
MAKEALL +1 -0
index cf05133..02b8595 100755
@@ -481,6 +481,7 @@ LIST_ARM7="		\
  	lpc2292sodimm	\
  	modnet50	\
  	SMN42		\
+	w90p1		\
  "
 
  #########################################################################
Makefile +3 -0
index 787c5f2..bbc62bb 100644
@@ -2916,6 +2916,9 @@ lpc2292sodimm_config:	unconfig
  SMN42_config	:	unconfig
  	@$(MKCONFIG) $(@:_config=) arm arm720t SMN42 siemens lpc2292
 
+W90P1_config	:	unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm720t w90p1
+
  #########################################################################
  ## ARM CORTEX Systems
  #########################################################################
board/w90p1/Makefile new file +53 -0

53 lines not on this page · raw message

board/w90p1/config.mk new file +24 -0
new file mode 100644
index 0000000..34f8978
@@ -0,0 +1,24 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x01FC0000
board/w90p1/ide.c new file +120 -0

120 lines not on this page · raw message

board/w90p1/led.c new file +61 -0

61 lines not on this page · raw message

board/w90p1/lowlevel_init.S new file +124 -0

124 lines not on this page · raw message

board/w90p1/nand.c new file +106 -0

106 lines not on this page · raw message

board/w90p1/u-boot.lds new file +69 -0

69 lines not on this page · raw message

board/w90p1/w90p1.c new file +95 -0

95 lines not on this page · raw message

examples/Makefile +4 -4
index 927010d..86636b5 100644
@@ -33,10 +33,10 @@ ifeq ($(ARCH),arm)
  ifeq ($(BOARD),omap2420h4)
  LOAD_ADDR = 0x80300000
  else
-ifeq ($(CPU),omap3)
-LOAD_ADDR = 0x80300000
-else
-LOAD_ADDR = 0xc100000
+ ifeq ($(BOARD),w90p1)
+  LOAD_ADDR = 0x00001000
+ else
+  LOAD_ADDR = 0xc100000
  endif
  endif
  endif
include/configs/W90P1.h new file +240 -0

240 lines not on this page · raw message

Signature · 1 line
1.5.4.3
#1 lore raw

PATCH 3/3 Add W90P1board based on W90P710 ARM SoC

Quoted 33 lines · Vovk Konstantin

W90P1 board support NAND and NOR Flash, IDE interface, optional LED for visualization. Changed makefile in /examples folder for support W90P710 SoC.

---
  MAINTAINERS                 |   13 ++-
  MAKEALL                     |    1 +
  Makefile                    |    3 +
  board/w90p1/Makefile        |   53 ++++++++++
  board/w90p1/config.mk       |   24 +++++
  board/w90p1/ide.c           |  120 +++++++++++++++++++++
  board/w90p1/led.c           |   61 +++++++++++
  board/w90p1/lowlevel_init.S |  124 ++++++++++++++++++++++
  board/w90p1/nand.c          |  106 +++++++++++++++++++
  board/w90p1/u-boot.lds      |   69 ++++++++++++
  board/w90p1/w90p1.c         |   95 +++++++++++++++++
  examples/Makefile           |    8 +-
  include/configs/W90P1.h     |  240 +++++++++++++++++++++++++++++++++++++++++++
  13 files changed, 908 insertions(+), 9 deletions(-)

create mode 100644 board/w90p1/Makefile
create mode 100644 board/w90p1/config.mk
create mode 100644 board/w90p1/ide.c
create mode 100644 board/w90p1/led.c
create mode 100644 board/w90p1/lowlevel_init.S
create mode 100644 board/w90p1/nand.c
create mode 100644 board/w90p1/u-boot.lds
create mode 100644 board/w90p1/w90p1.c
create mode 100644 include/configs/W90P1.h

MAINTAINERS +0 -0
index 38feac8..95b59dc 100644

MAINTAINERS Joe D'Abbraccio <[email protected]> · line 65

Quoted 5 lines
MAINTAINERS +1 -1
@@ -62,7 +62,7 @@ Joe D'Abbraccio <[email protected]>
 
  	MPC837xERDB	MPC837x
 
-K?ri Dav??sson <[email protected]>
+K???ri Dav??????sson <[email protected]>

??

MAINTAINERS Peter Figuli <[email protected]> · line 519

Quoted 9 lines
MAINTAINERS +1 -1
  	FLAGADM		MPC823
 
@@ -516,7 +516,7 @@ Peter Figuli <[email protected]>
 
  	wepep250	xscale
 
-Marius Gr?ger <[email protected]>
+Marius Gr???ger <[email protected]>

??

MAINTAINERS Nishanth Menon <[email protected]> · line 569

Quoted 9 lines
MAINTAINERS +1 -1
  	impa7		ARM720T (EP7211)
  	ep7312		ARM720T (EP7312)
@@ -566,7 +566,7 @@ Nishanth Menon <[email protected]>
 
  	omap3_zoom1	ARM CORTEX-A8 (OMAP3xx SoC)
 
-David M?ller <[email protected]>
+David M???ller <[email protected]>

??

MAINTAINERS Richard Woodruff <[email protected]> · line 649

Quoted 9 lines
MAINTAINERS +1 -1
  	smdk2410	ARM920T
  	VCMA9		ARM920T
@@ -646,7 +646,7 @@ Richard Woodruff <[email protected]>
 
  	omap2420h4	ARM1136EJS
 
-Alex Z?pke <[email protected]>
+Alex Z???pke <[email protected]>

??

Quoted 14 lines
MAINTAINERS +3 -0
  	lart		SA1100
  	dnp1110		SA1110
@@ -655,6 +655,9 @@ Sergey Lapin <[email protected]>
 
  	afeb9260	ARM926EJS (AT91SAM9260 SoC)
 
+Konstantin Vovk <[email protected]>
+	w90p1		ARM720T (W90P710 SoC)
+
  -------------------------------------------------------------------------
 
  Unknown / orphaned boards:

MAINTAINERS Unknown / orphaned boards: · line 677

Quoted 5 lines
MAINTAINERS +1 -1
@@ -671,7 +674,7 @@ Unknown / orphaned boards:
  #	Board		CPU						#
  #########################################################################
 
-Daniel Engstr?m <[email protected]>
+Daniel Engstr???m <[email protected]>

??

Quoted 54 lines
MAINTAINERS +0 -0
  	sc520_cdp	x86
 
MAKEALL +1 -0
index cf05133..02b8595 100755
@@ -481,6 +481,7 @@ LIST_ARM7="		\
  	lpc2292sodimm	\
  	modnet50	\
  	SMN42		\
+	w90p1		\
  "
 
  #########################################################################
Makefile +3 -0
index 787c5f2..bbc62bb 100644
@@ -2916,6 +2916,9 @@ lpc2292sodimm_config:	unconfig
  SMN42_config	:	unconfig
  	@$(MKCONFIG) $(@:_config=) arm arm720t SMN42 siemens lpc2292
 
+W90P1_config	:	unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm720t w90p1
+
  #########################################################################
  ## ARM CORTEX Systems
  #########################################################################
board/w90p1/Makefile new file +19 -0
new file mode 100644
index 0000000..d4d1cba
@@ -0,0 +1,53 @@
+
+#
+# (C) Copyright 2000-2008
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License

board/w90p1/Makefile line 29

Quoted 10 lines
board/w90p1/Makefile new file +10 -0
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y := $(BOARD).o
+COBJS-$(CONFIG_CMD_NAND)   += nand.o

please use tab

board/w90p1/Makefile line 30

Quoted 1 line
board/w90p1/Makefile new file +1 -0
+COBJS-$(CONFIG_CMD_IDE)    += ide.o

please use tab

Quoted 107 lines
board/w90p1/Makefile new file +23 -0
+COBJS-$(CONFIG_STATUS_LED) += led.o
+
+SOBJS := lowlevel_init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+#########################################################################
board/w90p1/config.mk new file +24 -0
new file mode 100644
index 0000000..34f8978
@@ -0,0 +1,24 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x01FC0000
board/w90p1/ide.c new file +48 -0
new file mode 100644
index 0000000..0c370b5
@@ -0,0 +1,120 @@
+/*
+ * (C) Copyright 2008
+ * KSL Embedded Development Team <www.kslemb.com>
+ * Konstantin Vovk <[email protected]>
+ *
+ * IDE interface for Winbond W90P710 ARM7 SoC
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+#include <common.h>
+#include <asm/hardware.h>
+
+#if defined(CONFIG_CMD_IDE)
+#include <ata.h>
+#include <ide.h>
+
+/*
+ * Define the start address of the IDE_CS0 region (0x73000000 but we wr/rd to
+ * the 0xF3000000 for disable internal cache memory MSB=1)
+ * Start Address for IDE CS0 - mapped to the EBI ECS1
+ */
+#define EXT1_BASE	0xF3000000
+/* Define the start address of the IDE_CS1 region (0x74000000 but we wr/rd to
+ * the 0xF4000000 for disable internal cache memory MSB=1)
+ * Start Address for IDE CS1 - mapped to the EBI ECS2
+ */
+#define EXT2_BASE	0xF4000000
+
+/* Config bits for ECS1 and ECS2 */
+
+#define SIZE_256k	(0 << 16)	/* Memory size is 256K */

board/w90p1/ide.c line 58

Quoted 10 lines
board/w90p1/ide.c new file +10 -0
+#define SIZE_512k	(1 << 16)	/* Memory size is 512K */
+#define SIZE_1M		(2 << 16)	/* Memory size is 1M   */
+#define SIZE_16M	(6 << 16)	/* Memory size is 16M  */
+#define SIZE_32M	(7 << 16)	/* Memory size is 32M  */
+
+#define ADRS		(1 << 15)
+#define tACC		(15 << 11)	/* Access cycles of external I/O bank */
+#define tCOH		(7 << 8)	/* Chip selection hold time */
+#define tACS		(7 << 5)	/* Address set-up before nECS */
+#define tCOS		(7 << 2)	/* Chip selection setup time */

please use upppercase
please move this to the header

Quoted 15 lines
board/w90p1/ide.c new file +15 -0
+
+#define BUS16		(2)		/* 16-bit bus width for IDE */
+#define BUS08		(1)		/* 8-bit bus width for IDE  */
+
+#define BUS_SETTINGS	(SIZE_256k | ADRS | tACC | tCOH | tACS | tCOS)
+#define BUS_16BIT	(BUS_SETTINGS |	BUS16)
+#define BUS_8BIT	(BUS_SETTINGS |	BUS08)
+
+/* IDE_CS0 with 16bit data bus */
+#define ENABLE16()   PUT_REG(REG_EXT1CON, ((EXT1_BASE << 1) | BUS_16BIT))
+/* IDE_CS0 with 8bit data bus */
+#define DISABLE16()  PUT_REG(REG_EXT1CON, ((EXT1_BASE << 1) | BUS_8BIT))
+
+void outb (unsigned char val, volatile unsigned char *addr)
+{

board/w90p1/ide.c line 83

Quoted 10 lines
board/w90p1/ide.c new file +10 -0
+ 	*(addr) = val;
+}
+
+unsigned char inb (volatile unsigned char *addr)
+{
+ 	volatile unsigned char c;
+
+ 	c = *(addr);
+ 	return c;
+}

please use the asm version of it

Quoted 14 lines
board/w90p1/ide.c new file +14 -0
+
+/*  IDE work with Data Port via 16-bit BUS that's why we must first of all
+ *  enable 16-bit bus on ECS1, read/write data to the Data Port, and finaly
+ *  disable 16-bit wide data bus
+ */
+void insw (unsigned short *addr, unsigned short *sect_buf, int words)
+{
+	int i;
+
+	ENABLE16 ();
+	for (i = 0; i < words; i++)
+		*(sect_buf + i) = *(addr);
+	DISABLE16 ();
+}

board/w90p1/ide.c line 107

Quoted 10 lines
board/w90p1/ide.c new file +10 -0
+
+void outsw (unsigned short *addr, unsigned short *sect_buf, int words)
+{
+	int i;
+
+	ENABLE16 ();
+	for (i = 0; i < words; i++)
+		*(addr) = *(sect_buf + i);
+	DISABLE16 ();
+}

ditto

Quoted 65 lines
board/w90p1/ide.c new file +13 -0
+
+int ide_preinit (void)
+{
+	/* Init IDE_CS0 with 8bit data bus */
+	PUT_REG (REG_EXT1CON, ((EXT1_BASE << 1) | BUS_8BIT));
+	/* Init IDE_CS1 with 8bit data bus */
+	PUT_REG (REG_EXT2CON, ((EXT2_BASE << 1) | BUS_8BIT));
+	/* Enable nWE as a write strob for ECS1 and ECS2 */
+	PUT_REG (REG_EBICON, GET_REG(REG_EBICON) | (1 << 25) | (1 << 26));
+
+	return 0;
+}
+#endif
board/w90p1/lowlevel_init.S new file +45 -0
new file mode 100644
index 0000000..83c40a3
@@ -0,0 +1,124 @@
+/*
+ * (C) Copyright 2008
+ * KSL Embedded Development Team <www.kslemb.com>
+ * Konstantin Vovk <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/hardware.h>
+
+/*
+ * Configure Memory Map
+ *
+ * This memory map allows us to relocate from FLASH to SRAM.  After
+ * power-on reset the CPU only knows about the FLASH memory at address
+ * 0x00000000.	After lowlevel_init completes the memory map will be:
+ *
+ * Memory Addr
+ * 0x00000000 to 0x02000000 - 32MB on board SDRAM via DD6 and DD7
+ * 0x7F000000 to 0x7F200000 - 2MB(16Bit) on board Flash M29W320ET via DD8
+ *
+ * Load all 6 memory registers with the STMIA instruction since
+ * memory access is disabled once these registers are written.
+ * The last register written re-enables memory access.
+ */
+
+/* Clock Skew Control register  */

board/w90p1/lowlevel_init.S line 55

Quoted 10 lines
board/w90p1/lowlevel_init.S new file +10 -0
+#define	CKSKEW	0xFFF01F00
+
+.globl lowlevel_init
+lowlevel_init:
+
+	/* Check version number of W90P710 to set the clock skew
+	 * The clock skew of W90P710 ver A = 0x7A
+	 * The clock skew of W90P710 ver B = 0x39
+	 */
+	LDR	r0, =REG_PDID

please do not use uppercase for ldr and ands

Quoted 63 lines
board/w90p1/lowlevel_init.S new file +19 -0
+	LDR	r0, [r0]
+	LDR	r1, =0x0F000000
+	ANDS	r0,r0,r1
+	BEQ	ver0
+	LDR	r1, =0x01000000
+	CMP	r0, r1
+	BEQ	ver1
+	B	unknow_version
+ver0:
+	LDR	r0, =0x0FF007A
+	B	skew_update
+ver1:
+	LDR	r0, =0x0FF0039
+skew_update:
+	LDR	r1, =CKSKEW
+	STR	r0,[r1]
+unknow_version:
+	/* Nothing to do */
+
board/w90p1/nand.c new file +37 -0
new file mode 100644
index 0000000..ea36123
@@ -0,0 +1,106 @@
+/*
+ * (C) Copyright 2008
+ * KSL Embedded Development Team <www.kslemb.com>
+ * Konstantin Vovk <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+
+     Date     Version               Description
+  16.01.2009   v1.1      Updated  w90p710_nand_hwcontrol function.
+                         for support new U-Boot 2009
+ */
+#include <asm/io.h>
+#include <common.h>
+#include <asm/hardware.h>
+
+#if defined(CONFIG_CMD_NAND)
+#include <nand.h>
+
+/* W90P710 EBI Config bits */
+#define	SIZE_256k	(0 << 16)	/* Memory size is 256K */
+#define	SIZE_512k	(1 << 16)	/* Memory size is 512K */

board/w90p1/nand.c line 47

Quoted 10 lines
board/w90p1/nand.c new file +10 -0
+#define	SIZE_1M		(2 << 16)	/* Memory size is 1M  */
+#define	SIZE_16M	(6 << 16)	/* Memory size is 16M */
+#define	SIZE_32M	(7 << 16)	/* Memory size is 32M */
+
+#define	ADRS		(1 << 15)	/* Bus alignment to the byte address */
+#define	tACC		(7 << 11)	/* Access cycles of external I/O bank */
+#define	tCOH		(7 << 8)	/* Chip selection hold time */
+#define	tACS		(7 << 5)	/* Address set-up before nECS */
+#define	tCOS		(7 << 2)	/* Chip selection setup time */
+#define	BUS08		(1)		/* Bus is 8 bit wide */

please move to header

Quoted 27 lines
board/w90p1/nand.c new file +27 -0
+
+#define BUS_SETTINGS	(SIZE_16M | ADRS | tACC | tCOH | tACS | tCOS | BUS08)
+/*
+ * Define the start address of the CS0 region (0x72000000 but we wr/rd to the
+ * 0xF2000000 for disable internal cache memory)
+ */
+#define	EXT0_BASE	0xF2000000
+
+/* Hardware specific access to control-lines */
+void w90p710_nand_hwcontrol (struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	ulong base = (ulong) this->IO_ADDR_W;
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		if (ctrl & NAND_CLE)
+			base = (base | W90P710_NAND_CLE);
+		else
+			base = (base & ~W90P710_NAND_CLE);
+		if (ctrl & NAND_ALE)
+			base = (base | W90P710_NAND_ALE);
+		else
+			base = (base & ~W90P710_NAND_ALE);
+
+		this->IO_ADDR_W = (void __iomem *) ( base );
+	}
+

board/w90p1/nand.c line 84

Quoted 10 lines
board/w90p1/nand.c new file +10 -0
+	this->IO_ADDR_R = this->IO_ADDR_W;
+
+	if (cmd != NAND_CMD_NONE)
+		writeb (cmd, this->IO_ADDR_W);
+}
+
+/* We use nWait pin that's why we don't think abot ready */
+int w90p710_nand_ready(struct mtd_info *mtd)
+{
+	return (1);

please use return x not return (x)

board/w90p1/nand.c

Quoted 6 lines
board/w90p1/nand.c new file +4 -0
+}
+
 
 
+DECLARE_GLOBAL_DATA_PTR;
+#define MACH_W90X700 1861

please do not add it use the mach file

Quoted 16 lines
board/w90p1/nand.c new file +16 -0
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+int board_init (void)
+{
+	/* arch number MACH_TYPE_W90P710 */
+	gd->bd->bi_arch_number = MACH_W90X700;
+
+	/* location of boot parameters */
+	gd->bd->bi_boot_params = 0x00000800;
+
+#ifdef CONFIG_STATUS_LED
+	status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
+#endif
+	return (0);
+}

board/w90p1/nand.c

Quoted 10 lines
board/w90p1/nand.c new file +10 -0
+
+int dram_init (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+#if CONFIG_NR_DRAM_BANKS == 2
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+#endif

is it not possible to detect it

Quoted 36 lines
board/w90p1/nand.c new file +30 -0
+
+	return (0);
+}
+
+#if defined(CONFIG_DRIVER_W90P710_ETH)
+int board_eth_init (bd_t *bis)
+{
+	return W90P710_EMC_initialize (bis);
+}
+#endif
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+	PHY_Reset ();
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+/* miscellaneous platform dependent initialisations */
+int misc_init_r (void)
+{
+#ifdef CONFIG_CMD_IDE
+	extern int ide_preinit (void);
+	/* Init ECS1 and ECS2 for working with memory mapped IDE */
+	ide_preinit ();
+#endif
+	return (0);
+}
+#endif
examples/Makefile +0 -0
index 927010d..86636b5 100644
@@ -33,10 +33,10 @@ ifeq ($(ARCH),arm)
  ifeq ($(BOARD),omap2420h4)

examples/Makefile ifeq ($(ARCH),arm) · line 39

Quoted 10 lines
examples/Makefile +4 -4
  LOAD_ADDR = 0x80300000
  else
-ifeq ($(CPU),omap3)
-LOAD_ADDR = 0x80300000
-else
-LOAD_ADDR = 0xc100000
+ ifeq ($(BOARD),w90p1)
+  LOAD_ADDR = 0x00001000
+ else
+  LOAD_ADDR = 0xc100000

nack please do not remove other laod addr

Quoted 104 lines
examples/Makefile +0 -0
  endif
  endif
  endif
include/configs/W90P1.h new file +95 -0
new file mode 100644
index 0000000..6e218ae
@@ -0,0 +1,240 @@
+/*
+ * (C) Copyright 2008
+ * KSL Embedded Development Team <www.kslemb.com>
+ * Konstantin Vovk <[email protected]>
+ *
+ * Configuation settings for W90P1 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start u-boot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ *
+ * #define CONFIG_SKIP_LOWLEVEL_INIT
+ */
+
+/*
+ * High Level Configuration Options
+ *
+ */
+#define CONFIG_ARM7		1	/* This is a ARM7 CPU	 */
+#define CONFIG_ARM_THUMB	1	/* this is an ARM7TDMI	 */
+#define CONFIG_W90P710		1	/* it's a W90P710 chip	 */
+#define CONFIG_W90P1		1	/* on an W90P1 Board	 */
+
+#define CONFIG_IDENT_STRING	"\nKSL uBoot port for W90P710 SoC v1.1"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE	128
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_DRIVER_W90P710_ETH	1
+#define CONFIG_DRIVER_W90P710_UART	1
+#define CONFIG_DRIVER_W90P710_FLASH	1
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL1		1	/* UART0 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE		115200
+
+/*
+ * BOOTP options
+ */
+
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+/*
+ * Board miscellaneous initializations: Init ECS1 and ECS2 for work with IDE bus
+ */
+#define CONFIG_MISC_INIT_R	1
+
+/* Enable NAND Flash support */
+#define CONFIG_CMD_NAND		1
+
+/* Enable IDE support */
+#define CONFIG_CMD_IDE		1

include/configs/W90P1.h line 105

Quoted 10 lines
include/configs/W90P1.h new file +10 -0
+
+/* Enable status LED */
+#define CONFIG_STATUS_LED	1
+
+/* If board support NAND flash */
+#if defined (CONFIG_CMD_NAND)
+
+#define NAND_MAX_CHIPS			1
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define W90P710_NAND_BASE		0xF2000000

is it exist multiple bank to use it?

Quoted 13 lines
include/configs/W90P1.h new file +13 -0
+#define W90P710_NAND_CLE		(1 << 20)	/* CLE Address line */
+#define W90P710_NAND_ALE		(1 << 21)	/* ALE Address line */
+/* Base Address of the memory mapped NAND flash interface */
+#define CONFIG_SYS_NAND_BASE		W90P710_NAND_BASE
+
+#endif /* CONFIG_CMD_NAND */
+
+/* If board support IDE interface */
+#if defined (CONFIG_CMD_IDE)
+
+#define CONFIG_DOS_PARTITION	1
+
+/* W90P710 memory mapped IDE/ATA stuff */

include/configs/W90P1.h line 128

Quoted 10 lines
include/configs/W90P1.h new file +10 -0
+#undef  CONFIG_IDE_8xx_DIRECT	/* no pcmcia interface required */
+#undef  CONFIG_IDE_LED		/* no led for ide supported     */
+#undef  CONFIG_IDE_RESET	/* no reset for ide supported   */
+
+#define CONFIG_SYS_IDE_MAXBUS		1	/* max is 1 IDE bus */
+/* max 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS * 1)
+
+/* W90P1 board implements work with Data and registers via ECS1*/
+#define CONFIG_SYS_ATA_BASE_ADDR	0xF3000000

maybe use macro for ECS1 & co

Quoted 27 lines
include/configs/W90P1.h new file +27 -0
+#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000		/* Offset for data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET	0x0000		/* Offset for normal register accesses */
+/* CONFIG_SYS_ATA_ALT_OFFSET is used for work with Control Block [CBR]
+ * registers with A0...A2 = 0x6,0x7
+ * uBoot used only 0x6 - Alter Status/Device Control register
+ * W90P1 board implements work with CBR via ECS2
+ */
+/* Offset for alternate registers must be identical to (EXT2_BASE-EXT1_BASE) */
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x01000000	
+
+#endif /* CONFIG_CMD_IDE */
+
+/* If board support Status LED */
+#if defined (CONFIG_STATUS_LED)
+
+#define CONFIG_BOARD_SPECIFIC_LED 1
+
+#define STATUS_LED_BIT		0x00000004		/* GPIO2 pin 60 */
+#define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 4)	/* 250ms */
+#define STATUS_LED_STATE	STATUS_LED_BLINKING
+#define STATUS_LED_ACTIVE	0		/* LED on for bit is '0' */
+#define STATUS_LED_BOOT		0		/* LED 0 used for boot status */
+#define STATUS_LED_DIR		0xFFF83004	/* GPIO Direction register */
+#define STATUS_LED_PORT		0xFFF83008	/* GPIO Data output register */
+
+#endif /* CONFIG_STATUS_LED */

include/configs/W90P1.h line 165

Quoted 10 lines
include/configs/W90P1.h new file +10 -0
+
+/* Enable Ping command */
+#define CONFIG_CMD_PING
+/* Enable one or more MAC's support */
+#define CONFIG_NET_MULTI
+
+#define CONFIG_ETHADDR		00:40:95:36:35:33
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_IPADDR		192.168.0.84
+#define CONFIG_SERVERIP		192.168.0.4

please remove network CONFIG_

Quoted 7 lines
include/configs/W90P1.h new file +7 -0
+
+/* Enable PHY Reset after MAC Init */
+/*#define CONFIG_RESET_PHY_R*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+#define CONFIG_BOOTDELAY	2	/* delay for automatic boot */
+/*#define CONFIG_SYS_AUTOLOAD	"no"*/	/*rarpb, bootp or dhcp commands will perform only*/

include/configs/W90P1.h line 182

Quoted 10 lines
include/configs/W90P1.h new file +10 -0
+
+#define CONFIG_LOADADDR		0x8000	/* default load address */
+#define CONFIG_BOOTCOMMAND	"bootm 0x7F090000" /* Start uClinux from NOR Flash */
+/*#define CONFIG_BOOTCOMMAND	"tftp 0x8000 uImage"*/
+
+#define CONFIG_BOOTARGS		"console=ttyS0,115200 root=/dev/hda1 rw"
+
+/*
+ * Miscellaneous configurable options
+ */

Best Regards,
J.