8xx: add support for new keymile kmsupx4 board.
Subsystems (3)
PATCH 12/12 8xx: add support for new keymile kmsupx4 board.
This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C bitbang
Signed-off-by Heiko Schocher <[email protected]>
--- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 ++ board/keymile/common/common.c | 6 ++++- board/keymile/km8xx/km8xx.c | 7 +++++- cpu/mpc8xx/cpu_init.c | 2 + cpu/mpc8xx/start.S | 3 +- drivers/hwmon/lm75.c | 2 + drivers/i2c/soft_i2c.c | 3 ++ include/commproc.h | 8 +++--- include/configs/km8xx.h | 46 ++++++++++++++++++++++++++++++++--------- include/configs/kmsupx4.h | 38 +++++++++++++++++++++++++++++++++ include/configs/mgsuvd.h | 1 + lib_ppc/board.c | 3 +- 14 files changed, 106 insertions(+), 18 deletions(-) create mode 100644 include/configs/kmsupx4.h
MAINTAINERS +1 -0
@@ -380,6 +380,7 @@ Heiko Schocher <[email protected]> ids8247 MPC8247 jupiter MPC5200 kmeter1 MPC8360 + kmsupx4 MPC852T mgcoge MPC8247 mgsuvd MPC852 mucmc52 MPC5200
MAKEALL +1 -0
@@ -117,6 +117,7 @@ LIST_8xx=" \ KUP4X \ LANTEC \ lwmon \ + kmsupx4 \ MBX \ MBX860T \ mgsuvd \
Makefile +3 -0
@@ -921,6 +921,9 @@ IVMS8_config: unconfig } @$(MKCONFIG) -a IVMS8 ppc mpc8xx ivm +kmsupx4_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc8xx km8xx keymile + KUP4K_config : unconfig @$(MKCONFIG) $(@:_config=) ppc mpc8xx kup4k kup
board/keymile/common/common.c +5 -1
@@ -295,11 +295,14 @@ int ivm_analyze_eeprom (unsigned char *buf, int len)int ivm_read_eeprom (void ) { +#if defined(CONFIG_I2C_MUX )I2C_MUX_DEVICE *dev =NULL ; +#endif uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN ];uchar *buf;unsigned dev_addr =CONFIG_SYS_IVM_EEPROM_ADR ; +#if defined(CONFIG_I2C_MUX )/* First init the Bus, select the Bus */ #if defined(CONFIG_SYS_I2C_IVM_BUS ) dev =i2c_mux_ident_muxstring ((uchar *)CONFIG_SYS_I2C_IVM_BUS );
@@ -313,6 +316,7 @@ int ivm_read_eeprom (void) return -1; }i2c_set_bus_num (dev->busid); +#endif buf = (unsigned char *)getenv ("EEprom_ivm_addr" );if (buf !=NULL )
@@ -390,7 +394,7 @@ static void setports (int gpio)#endif #endif -#if defined(CONFIG_MGSUVD ) +#if defined(CONFIG_KM8XX )static void set_sda (int state) {I2C_SDA (state);
board/keymile/km8xx/km8xx.c +6 -1
@@ -61,7 +61,12 @@ const uint sdram_table[] =int checkboard (void ) { -puts ("Board: Keymile mgsuvd" ); +puts ("Board: Keymile " ); +#if defined(CONFIG_KMSUPX4 ) +puts ("kmsupx4" ); +#else +puts ("mgsuvd" ); +#endif if (ethernet_present ())puts (" with PIGGY." );puts ("\n" );
cpu/mpc8xx/cpu_init.c +2 -0
@@ -119,11 +119,13 @@ void cpu_init_f (volatile immap_t * immr)* Memory Controller: */ +#if !defined(CONFIG_KMSUPX4 )/* perform BR0 reset that MPC850 Rev. A can't guarantee */ reg = memctl->memc_br0; reg &=BR_PS_MSK ;/* Clear everything except Port Size bits */ reg |=BR_V ;/* then add just the "Bank Valid" bit */ memctl->memc_br0 = reg; +#endif /* Map banks 0 (and maybe 1) to the FLASH banks 0 (and 1) at * preliminary addresses - these have to be modified later
cpu/mpc8xx/start.S +2 -1
@@ -142,7 +142,8 @@ boot_warm: lis r3, IDC_DISABLE at h /* Disable data cache */ mtspr DC_CST, r3 -#if !(defined(CONFIG_IP860) || defined(CONFIG_PCU_E) || defined (CONFIG_FLAGADM)) +#if !(defined(CONFIG_IP860) || defined(CONFIG_PCU_E) || \ + defined (CONFIG_FLAGADM) || defined(CONFIG_KMSUPX4)) /* On IP860 and PCU E, * we cannot enable IC yet */
drivers/hwmon/lm75.c +2 -0
@@ -159,6 +159,7 @@ int dtt_init (void)/* switch to correct I2C bus */ old_bus =I2C_GET_BUS (); +#if defined(CONFIG_I2C_MUX )if ((gd->flags &GD_FLG_RELOC ) !=GD_FLG_RELOC ) {uchar *tmp = (uchar *)getenv ("dtt_bus" );if (tmp ==NULL )
@@ -170,6 +171,7 @@ int dtt_init (void) } else {I2C_SET_BUS (CONFIG_SYS_DTT_BUS_NUM ); } +#endif for (i =0 ; i <sizeof (sensors); i++) {if (_dtt_init (sensors[i]) !=0 )
drivers/i2c/soft_i2c.c +3 -0
@@ -43,6 +43,9 @@#ifdef CONFIG_MPC866 /* only valid for MPC866 */ #include <asm/io.h> #endif +#ifdef CONFIG_MPC852T /* only valid for MPC852T */ +#include <asm/io.h> +#endif #include <i2c.h> /* #define DEBUG_I2C */
include/commproc.h +4 -4
@@ -1122,11 +1122,11 @@ typedef struct scc_enet {#define SICR_ENET_CLKRT ((uint)0x0000003d)#endif /* CONFIG_MBX */ -/*** MGSUVD *********************************************************/ +/*** KM8XX *********************************************************/ -/* The MGSUVD Service Module uses SCC3 for Ethernet */ +/* The KM8XX Service Module uses SCC3 for Ethernet */ -#ifdef CONFIG_MGSUVD +#ifdef CONFIG_KM8XX #define PROFF_ENET PROFF_SCC3/* Ethernet on SCC3 */ #define CPM_CR_ENET CPM_CR_CH_SCC3#define SCC_ENET 2
@@ -1145,7 +1145,7 @@ typedef struct scc_enet {*/ #define SICR_ENET_MASK ((uint)0x00FF0000)#define SICR_ENET_CLKRT ((uint)0x00250000) -#endif /* CONFIG_MGSUVD */ +#endif /* CONFIG_KM8XX */ /*** MHPC ********************************************************/
include/configs/km8xx.h +36 -10
108 lines not on this page · raw message
include/configs/kmsupx4.h new file +38 -0
@@ -0,0 +1,38 @@ +/* +* (C) Copyright 2009 +* Heiko Schocher, DENX Software Engineering, hs at denx.de. +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +/* +* board/config.h - configuration options, board specific +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MPC852T 1/* This is a MPC852T CPU */ +#define CONFIG_KMSUPX4 1/* ...on a kmsupx4 board */ +#define CONFIG_HOSTNAME kmsupx4 + +/* include common defines/options for all Keymile 8xx boards */ +#include "km8xx.h" + +#endif /* __CONFIG_H */
include/configs/mgsuvd.h +1 -0
@@ -28,6 +28,7 @@#ifndef __CONFIG_H#define __CONFIG_H +#define CONFIG_MPC866 1/* This is a MPC866 CPU */ #define CONFIG_MGSUVD 1/* ...on a mgsuvd board */ #define CONFIG_HOSTNAME mgsuvd
lib_ppc/board.c +2 -1
@@ -737,7 +737,8 @@ void board_init_r (gd_t *id, ulong dest_addr)WATCHDOG_RESET ();#if defined(CONFIG_IP860 ) || defined(CONFIG_PCU_E ) || \ - defined (CONFIG_FLAGADM ) || defined(CONFIG_MPC83XX ) + defined (CONFIG_FLAGADM ) || defined(CONFIG_MPC83XX ) || \ + defined (CONFIG_KMSUPX4 )icache_enable ();/* it's time to enable the instruction cache */ #endif
Signature · 5 lines
1.6.0.6 -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany